Low Voltage PLL Clock Driver
MPC9351
PRODUCT DISCONTINUATION NOTICE - LAST TIME BUY EXPIRES SEPTEMBER 7, 2016
DATA SHEET
The MPC9351 is a 2.5V and 3.3V compatible, PLL based clock generator
targeted for high performance clock distribution systems. With output
frequencies of up to 200 MHz and a maximum output skew of 150ps, the
MPC9351 is an ideal solution for the most demanding clock tree designs. The
device offers 9 low-skew clock outputs, each is configurable to support the
clocking needs of the various high-performance microprocessors including the
PowerQUICC II integrated communication microprocessor. The extended
temperature range of the MPC9351 supports telecommunication and networking
requirements.The device employs a fully differential PLL design to minimize
cycle-to-cycle and long-term jitter.
MPC9351
LOW VOLTAGE
2.5 V AND 3.3 V PLL
CLOCK GENERATOR
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
9 Outputs LVCMOS PLL Clock Generator
25 – 200MHz Output Frequency Range
Fully Integrated PLL
2.5V and 3.3V Compatible
Compatible to Various Microprocessors Such as PowerQuicc II
Supports Networking, Telecommunications and Computer Applications
Configurable Outputs: Divide-by-2, 4 and 8 of VCO Frequency
LVPECL and LVCMOS Compatible Inputs
External Feedback Enables Zero-Delay Configurations
Output Enable/disable and Static Test Mode (PLL Enable/Disable)
Low Skew Characteristics: Maximum 150ps Output-to-Output
Cycle-to-Cycle Jitter Max. 22ps RMS
32-Lead LQFP Package, Pb-Free
Ambient Temperature Range -40°C to +85°C
For functional replacement use 8T49N285
AC SUFFIX
32-LEAD LQFP PACKAGE
Pb-FREE PACKAGE
CASE 873A-03
Functional Description
The MPC9351 utilizes PLL technology to frequency and phase lock its outputs onto an input reference clock. Normal operation
of the MPC9351 requires a connection of one of the device outputs to the EXT_FB input to close the PLL feedback path. The
reference clock frequency and the output divider for the feedback path determine the VCO frequency. Both must be selected to
match the VCO frequency range. With available output dividers of divide-by-2, divide-by-4 and divide-by-8, the internal VCO of
the MPC9351 is running at either 2x, 4x or 8x of the reference clock frequency. The frequency of the QA, QB, QC and QD outputs
is either the one-half, one-fourth or one-eighth of the selected VCO frequency and can be configured for each output bank using
the FSELA, FSELB, FSELC and FSELD pins, respectively. The available output-to-input frequency ratios are 4:1, 2:1, 1:1, 1:2
and 1:4. The REF_SEL pin selects the differential LVPECL (PCLK and PCLK) or the LVCMOS compatible reference input
(TCLK). The MPC9351 also provides a static test mode when the PLL enable pin (PLL_EN) is pulled to logic low state. In test
mode, the selected input reference clock is routed directly to the output dividers bypassing the PLL. The test mode is intended
for system diagnostics, test and debug purposes. This test mode is fully static and the minimum clock frequency specification
does not apply. The outputs can be disabled by deasserting the OE pin (logic high state). In PLL mode, deasserting OE causes
the PLL to loose lock due to no feedback signal presence at EXT_FB. Asserting OE will enable the outputs and close the phase
locked loop, also enabling the PLL to recover to normal operation. The MPC9351 is fully 2.5 V and 3.3 V compatible and requires
no external loop filter components. All inputs except PCLK and PCLK accept LVCMOS signals, while the outputs provide
LVCMOS compatible levels with the capability to drive terminated 50 transmission lines. For series terminated transmission
lines, each of the MPC9351 outputs can drive one or two traces giving the device an effective fanout of 1:18. The device is packaged in a 7x7 mm2 32-lead LQFP package.
Application Information
The fully integrated PLL of the MPC9351 allows the low-skew outputs to lock onto a clock input and distribute it with essentially
zero propagation delay to multiple components on the board. In zero-delay buffer mode, the PLL minimizes phase offset between
the outputs and the reference signal.
MPC9351 REVISION 7 3/14/16
1
©2016 Integrated Device Technology, Inc.
MPC9351 DATA SHEET
PCLK
PCLK
TCLK
(Pullup)
(Pulldown)
REF_SEL
(Pulldown)
EXT_FB
(Pulldown)
0
0
2
Ref
1
1
PLL
0
4
D
Q
QA
D
Q
QB
1
8
FB
0
200 – 400 MHz
1
PLL_EN
(Pullup)
QC0
0
FSELA
FSELB
(Pulldown)
FSELC
(Pulldown)
FSELD
(Pulldown)
D
Q
QC1
1
(Pulldown)
QD0
QD1
0
D
Q
QD2
1
QD3
QD4
OE
(Pulldown)
The MPC9351 requires an external RC filter for the analog power supply pin VCCA. Please see application section for details.
QC0
VCCO
QC1
GND
QD0
VCCO
QD1
GND
Figure 1. MPC9351 Logic Diagram
24
23
22
21
20
19
18
17
GND
25
16
QD2
QB
26
15
VCCO
VCCO
27
14
QD3
QA
28
13
GND
GND
29
12
QD4
TCLK
30
11
VCCO
PLL_EN
31
10
OE
REF_SEL
32
MPC9351
2
3
4
5
6
7
8
VCCA
EXT_FB
FSELA
FSELB
FSELC
FSELD
GND
PCLK
9
1
PCLK
Figure 2. Pinout: 32-Lead Package Pinout (Top View)
LOW VOLTAGE PLL CLOCK DRIVER
2
REVISION 7 3/14/16
MPC9351 DATA SHEET
Table 1. Pin Descriptions
Number
Name
Type
Description
PCLK, PCLK
Input
LVPECL
Differential clock reference
Low voltage positive ECL input
TCLK
Input
LVCMOS
Single ended reference clock signal or test clock
EXT_FB
Input
LVCMOS
Feedback signal input, connect to a QA, QB, QC, QD output
REF_SEL
Input
LVCMOS
Selects input reference clock
FSELA
Input
LVCMOS
Output A divider selection
FSELB
Input
LVCMOS
Output B divider selection
FSELC
Input
LVCMOS
Outputs C divider selection
FSELD
Input
LVCMOS
Outputs D divider selection
OE
Input
LVCMOS
Output enable/disable
QA
Output
LVCMOS
Bank A clock output
QB
Output
LVCMOS
Bank B clock output
QC0, QC1
Output
LVCMOS
Bank C clock outputs
QD0 – QD4
Output
LVCMOS
Bank D clock outputs
VCCA
Supply
VCC
Positive power supply for the PLL
VCC
Supply
VCC
Positive power supply for I/O and core
GND
Supply
Ground
Negative power supply
Table 2. Function Table
Control
Default
0
1
REF_SEL
0
Selects PCLK as reference clock
Selects TCLK as reference clock
PLL_EN
1
Test mode with PLL disabled. The input clock is
directly routed to the output dividers
PLL enabled. The VCO output is routed to the
output dividers
OE
0
Outputs enabled
Outputs disabled, PLL loop is open
VCO is forced to its minimum frequency
FSELA
0
QA = VCO 2
QA = VCO 4
FSELB
0
QB = VCO 4
QB = VCO 8
FSELC
0
QC = VCO 4
QC = VCO 8
FSELD
0
QD = VCO 4
QD = VCO 8
Table 3. Absolute Maximum Ratings(1)
Symbol
Characteristics
Min
Max
Unit
VCC
Supply Voltage
–0.3
4.6
V
VIN
DC Input Voltage
–0.3
VCC+0.3
V
DC Output Voltage
–0.3
VCC+0.3
V
DC Input Current
20
mA
DC Output Current
50
mA
150
°C
VOUT
IIN
IOUT
TS
Storage Temperature
–55
1. Absolute maximum continuous ratings are those maximum values beyond which damage to the device may occur. Exposure to these
conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute-maximum-rated
conditions is not implied.
REVISION 7 3/14/16
3
©2016 INTEGRATED DEVICE TECHNOLOGY, INC.
MPC9351 DATA SHEET
Table 4. General Specifications
Symbol
Characteristics
Min
Typ
Max
Unit
VCC 2
Condition
VTT
Output Termination Voltage
V
MM
ESD (Machine Model)
200
V
HBM
ESD (Human Body Model)
2000
V
LU
Latch-Up
200
mA
CPD
Power Dissipation Capacitance
10
pF
Per output
CIN
Input Capacitance
4.0
pF
Inputs
Table 5. DC Characteristics (VCC = 3.3 V 5%, TA = -40° to 85°C)
Symbol
Characteristics
Min
VIH
Input High Voltage
VIL
Input Low Voltage
VPP
Peak-to-Peak Input Voltage PCLK, PCLK
250
Common Mode Range
1.0
VCMR(1)
VOH
Output High Voltage
VOL
Output Low Voltage
ZOUT
Output Impedance
IIN
Typ
2.0
PCLK, PCLK
Max
Unit
VCC + 0.3
V
LVCMOS
0.8
V
LVCMOS
mV
LVPECL
V
LVPECL
V
IOH = –24 mA(2)
V
V
IOL = 24 mA
IOL = 12 mA
VCC – 0.6
2.4
0.55
0.30
14 –17
Input Leakage Current
ICCA
Maximum PLL Supply Current
3.0
ICCQ
Maximum Quiescent Supply Current
Condition
200
A
VIN = VCC or GND
5.0
mA
VCCA Pin
1.0
mA
All VCC Pins
1. VCMR (DC) is the crosspoint of the differential input signal. Functional operation is obtained when the crosspoint is within the VCMR range
and the input swing lies within the VPP (DC) specification.
2. The MPC9351 is capable of driving 50 transmission lines on the incident edge. Each output drives one 50 parallel terminated
transmission line to a termination voltage of VTT. Alternatively, the device drives up to two 50 series terminated transmission lines.
Table 6. AC Characteristics (VCC = 3.3 V 5%, TA = -40° to 85°C)(1)
Symbol
Characteristics
Min
2 feedback
4 feedback
8 feedback
Static test mode
Typ
Max
Unit
100
50
25
0
200
100
50
300
MHz
MHz
MHz
MHz
200
400
MHz
100
50
25
200
100
50
MHz
MHz
MHz
Condition
fref
Input Frequency
fVCO
VCO Frequency
fMAX
Maximum Output Frequency
frefDC
Reference Input Duty Cycle
25
75
%
Peak-to-Peak Input Voltage PCLK, PCLK
500
1000
mV
LVPECL
Common Mode Range
1.2
VCC – 0.9
V
LVPECL
1.0
ns
0.8 to 2.0V
+150
+325
ps
ps
PLL locked
PLL locked
VPP
VCMR(2)
2 output
4 output
8 output
PCLK, PCLK
tr, tf
TCLK Input Rise/Fall Time
t()
Propagation Delay (static phase offset)
TCLK to EXT_FB
PCLK to EXT_FB
LOW VOLTAGE PLL CLOCK DRIVER
–50
+25
4
PLL_EN = 1
PLL_EN = 1
PLL_EN = 1
PLL_EN = 0
REVISION 7 3/14/16
MPC9351 DATA SHEET
Table 6. AC Characteristics (VCC = 3.3 V 5%, TA = -40° to 85°C)(1) (Continued)
Symbol
tsk(o)
Characteristics
Min
Typ
Output-to-Output Skew
50
50
50
150
ps
55
52.5
51.75
%
%
%
1.0
ns
Output Duty Cycle
tr, tf
Output Rise/Fall Time
tPLZ, HZ
Output Disable Time
10
ns
tPZL, ZH
Output Enable Time
10
ns
PLL closed loop bandwidth
45
47.5
48.75
Unit
DC
BW
100 – 200 MHz
50 – 100 MHz
25 – 50 MHz
Max
0.1
2 feedback
4 feedback
8 feedback
9.0 –- 20.0
3.0 – 9.5
1.2 – 2.1
MHz
MHz
MHz
Condition
0.55 to 2.4 V
–3 db point of
PLL transfer characteristic
tJIT(CC)
Cycle-to-cycle jitter
4 feedback
Single Output Frequency Configuration
10
22
ps
RMS value
tJIT(PER)
Period Jitter
4 feedback
Single Output Frequency Configuration
8.0
15
ps
RMS value
ps
RMS value
tJIT()
I/O Phase Jitter
tLOCK
Maximum PLL Lock Time
4.0 – 17
1.0
ms
1. AC characteristics apply for parallel output termination of 50 to VTT.
2. VCMR (AC) is the crosspoint of the differential input signal. Normal AC operation is obtained when the crosspoint is within the VCMR range
and the input swing lies within the VPP (AC) specification. Violation of VCMR or VPP impacts static phase offset t().
Table 7. DC Characteristics (VCC = 2.5 V 5%, TA = -40° to 85°C)
Symbol
Characteristics
Min
VIH
Input High Voltage
VIL
Input Low Voltage
VPP
Peak-to-Peak Input Voltage PCLK, PCLK
250
Common Mode Range
1.0
VCMR(1)
VOH
Output High Voltage
VOL
Output Low Voltage
ZOUT
Output Impedance
Typ
1.7
PCLK, PCLK
Max
Unit
VCC + 0.3
V
LVCMOS
0.7
V
LVCMOS
mV
LVPECL
V
LVPECL
V
IOH = –15 mA(2)
V
IOL = 15 mA
VCC – 0.6
1.8
0.6
Condition
17 – 20
200
A
IIN
Input Leakage Current
VIN = VCC or GND
CIN
Input Capacitance
4.0
pF
CPD
Power Dissipation Capacitance
10
pF
Per Output
ICCA
Maximum PLL Supply Current
3.0
5.0
mA
VCCA Pin
ICCQ
Maximum Quiescent Supply Current
1.0
mA
All VCC Pins
1. VCMR (DC) is the crosspoint of the differential input signal. Functional operation is obtained when the crosspoint is within the VCMR range
and the input swing lies within the VPP (DC) specification.
2. The MPC9351 is capable of driving 50 transmission lines on the incident edge. Each output drives one 50 parallel terminated
transmission line to a termination voltage of VTT. Alternatively, the device drives up to two 50 series terminated transmission lines per
output.
REVISION 7 3/14/16
5
©2016 INTEGRATED DEVICE TECHNOLOGY, INC.
MPC9351 DATA SHEET
Table 8. AC Characteristics (VCC = 2.5 V 5%, TA = -40° to 85°C)(1)
Symbol
Characteristics
Min
2 feedback
4 feedback
8 feedback
Typ
Max
Unit
100
50
25
200
100
50
MHz
MHz
MHz
200
400
MHz
100
50
25
200
100
50
MHz
MHz
MHz
Condition
fref
Input Frequency
fVCO
VCO Frequency
fMAX
Maximum Output Frequency
frefDC
Reference Input Duty Cycle
25
75
%
Peak-to-Peak Input Voltage PCLK, PCLK
500
1000
mV
LVPECL
Common Mode Range
1.2
VCC – 0.6
V
LVPECL
1.0
ns
0.7 to 1.7 V
+100
+300
ps
ps
PLL locked
PLL locked
150
ps
55
52.5
51.75
%
%
%
1.0
ns
VPP
VCMR(2)
2 output
4 output
8 output
PCLK, PCLK
tr, tf
TCLK Input Rise/Fall Time
t()
Propagation Delay (static phase offset)
TCLK to EXT_FB
PCLK to EXT_FB
tsk(o)
–100
0
Output-to-Output Skew
DC
Output Duty Cycle
tr, tf
Output Rise/Fall Time
tPLZ, HZ
Output Disable Time
12
ns
tPZL, ZH
Output Enable Time
12
ns
BW
PLL closed loop bandwidth
100 – 200 MHz
50 – 100 MHz
25 – 50 MHz
45
47.5
48.75
50
50
50
0.1
2 feedback
4 feedback
8 feedback
4.0 – 15.0
2.0 – 7.0
0.7 – 2.0
MHz
MHz
MHz
0.6 to 1.8 V
–3 dB point of PLL transfer
characteristic
tJIT(CC)
Cycle-to-cycle jitter
4 feedback
Single Output Frequency Configuration
10
22
ps
RMS value
tJIT(PER)
Period Jitter
4 feedback
Single Output Frequency Configuration
8.0
15
ps
RMS value
ps
RMS value
tJIT()
I/O Phase Jitter
tLOCK
Maximum PLL Lock Time
6.0 – 25
1.0
ms
1. AC characteristics apply for parallel output termination of 50 to VTT.
2. VCMR (AC) is the crosspoint of the differential input signal. Normal AC operation is obtained when the crosspoint is within the VCMR range
and the input swing lies within the VPP (AC) specification. Violation of VCMR or VPP impacts static phase offset t().
LOW VOLTAGE PLL CLOCK DRIVER
6
REVISION 7 3/14/16
MPC9351 DATA SHEET
APPLICATIONS INFORMATION
Programming the MPC9351
The MPC9351 clock driver outputs can be configured into
several divider modes; in addition, the external feedback of
the device allows for flexibility in establishing various input to
output frequency relationships. The output divider of the four
output groups allows the user to configure the outputs into
1:1, 2:1, 4:1 and 4:2:1 frequency ratios. The use of even
dividers ensures that the output duty cycle is always 50%.
Table 9 illustrates the various output configurations. The
table describes the outputs using the input clock frequency
CLK as a reference.
The output division settings establish the output
relationship. In addition, it must be ensured that the VCO will
be stable given the frequency of the outputs desired. The
feedback frequency should be used to situate the VCO into a
frequency range in which the PLL will be stable. The design
of the PLL supports output frequencies from 25MHz to
200MHz, while the VCO frequency range is specified from
200MHz to 400MHz and should not be exceeded for stable
operation.
Table 9. Output Frequency Relationship(1) for an Example Configuration
Inputs
Outputs
FSELA
FSELB
FSELC
FSELD
QA
QB
QC
QD
0
0
0
0
2 * CLK
CLK
CLK
CLK
0
0
0
1
2 * CLK
CLK
CLK
CLK 2
0
0
1
0
4 * CLK
2 * CLK
CLK
2* CLK
0
0
1
1
4 * CLK
2 * CLK
CLK
CLK
0
1
0
0
2 * CLK
CLK 2
CLK
CLK
0
1
0
1
2 * CLK
CLK 2
CLK
CLK 2
0
1
1
0
4 * CLK
CLK
CLK
2 * CLK
0
1
1
1
4 * CLK
CLK
CLK
CLK
1
0
0
0
CLK
CLK
CLK
CLK
1
0
0
1
CLK
CLK
CLK
CLK 2
1
0
1
0
2 * CLK
2 * CLK
CLK
2 * CLK
1
0
1
1
2 * CLK
2 * CLK
CLK
CLK
1
1
0
0
CLK
CLK 2
CLK
CLK
1
1
0
1
CLK
CLK 2
CLK
CLK 2
1
1
1
0
2 * CLK
CLK
CLK
2 * CLK
1
1
1
1
2 * CLK
CLK
CLK
CLK
1. Output frequency relationship with respect to input reference frequency CLK. QC1 is connected to EXT_FB. More frequency ratios are
available by the connection of QA to the feedback input (EXT_FB).
the output-to-output skew (tSK(O) relative to the feedback
output.
Using the MPC9351 in Zero-Delay Applications
Nested clock trees are typical applications for the
MPC9351. For these applications, the MPC9351 offers a
differential LVPECL clock input pair as a PLL reference. This
allows for the use of differential LVPECL primary clock
distribution devices such as the Freescale MC100EP111 or
MC10EP222, taking advantage of its superior low-skew
performance. Clock trees using LVPECL for clock
distribution, and the MPC9351 as LVCMOS PLL fanout buffer
with zero insertion delay, will show significantly lower clock
skew than clock distributions developed from CMOS fanout
buffers.
The external feedback option of the MPC9351 PLL allows
for its use as a zero-delay buffer. The PLL aligns the feedback
clock output edge with the clock input reference edge and
virtually eliminates the propagation delay through the device.
The remaining insertion delay (skew error) of the
MPC9351 in zero-delay applications is measured between
the reference clock input and any output. This effective delay
consists of the static phase offset (SPO or t()), I/O jitter
(tJIT(), phase or long-term jitter), feedback path delay and
REVISION 7 3/14/16
fref = 100 MHz
TCLK
QA
QB
2 x 100 MHz
QC0
QC1
2 x 100 MHz
4 x 100 MHz
1
REF_SEL
1
1
0
0
0
PLL_EN
FSELA
FSELB
FSELC
FSELD
QD0
QD1
QD2
QD3
Ext_FB
QD4
MPC9351
100 MHz (Feedback)
Figure 3. MPC9351 Zero-Delay Configuration
(Feedback of QD4)
7
©2016 INTEGRATED DEVICE TECHNOLOGY, INC.
MPC9351 DATA SHEET
Calculation of Part-to-Part Skew
The MPC9351 zero-delay buffer supports applications
where critical clock signal timing can be maintained across
several devices. If the reference clock inputs (TCLK or PCLK)
of two or more MPC9351 are connected together, the
maximum overall timing uncertainty from the common TCLK
input to any output is:
Above equation uses the maximum I/O jitter number
shown in the AC characteristic table for VCC = 3.3 V (17 ps
RMS). I/O jitter is frequency dependant with a maximum at
the lowest VCO frequency (200 MHz for the MPC9351).
Applications using a higher VCO frequency exhibit less I/O
jitter than the AC characteristic limit. The I/O jitter
characteristics in Figure 5 and Figure 6 can be used to derive
a smaller I/O jitter number at the specific VCO frequency,
resulting in tighter timing limits in zero-delay mode and for
part-to-part skew (tSK(PP)).
tSK(PP) = t() + tSK(O) + tPD, LINE(FB) + tJIT() · CF
This maximum timing uncertainty consist of 4 components:
static phase offset, output skew, feedback board trace delay
and I/O (phase) jitter:
Max. I/O Jitter versus Frequency
30
25
TCLKCommon
—t(ý)
QFBDevice 1
tJIT(ý) [ps] ms
tPD,LINE(FB)
tJIT()
20
15
10
5
Any QDevice 1
0
+tSK(O)
75
+t()
QFBDevice2
275
300
325
350
375
400
VCO Frequency [MHz]
tJIT()
Max. I/O Jitter versus Frequency
+tSK(O)
Max. skew
30
25
tSK(PP)
Figure 4. MPC9351 Maximum Device-to-Device Skew
Due to the statistical nature of I/O jitter, a RMS value (1 )
is specified. I/O jitter numbers for other confidence factors
(CF) can be derived from Table 10.
CF
Probability of Clock Edge within the Distribution
1
0.68268948
2
0.95449988
3
0.99730007
4
0.99993663
5
0.99999943
6
0.99999999
20
15
10
5
0
Table 10. Confidence Factor CF
75
225
250
275
300
325
350
375
400
VCO Frequency [MHz]
Figure 6. Maximum I/O Jitter (RMS)
versus Frequency for VCC = 3.3 V
Power Supply Filtering
The MPC9351 is a mixed analog/digital product. Its analog
circuitry is naturally susceptible to random noise, especially if
this noise is seen on the power supply pins. Noise on the
VCCA (PLL) power supply impacts the device characteristics,
for instance, I/O jitter. The MPC9351 provides separate
power supplies for the output buffers (VCC) and the
phase-locked loop (VCCA) of the device. The purpose of this
design technique is to isolate the high switching noise digital
outputs from the relatively sensitive internal analog
phase-locked loop. In a digital system environment, where it
is more difficult to minimize noise on the power supplies, a
second level of isolation may be required. The simple but
effective form of isolation is a power supply filter on the VCCA
pin for the MPC9351. Figure 7 illustrates a typical power
supply filter scheme. The MPC9351 frequency and phase
stability is most susceptible to noise with spectral content in
The feedback trace delay is determined by the board
layout and can be used to fine-tune the effective delay
through each device. In the following example calculation, an
I/O jitter confidence factor of 99.7% ( 3) is assumed,
resulting in a worst case timing uncertainty from input to any
output of –251 ps to 351 ps relative to TCLK (VCC = 3.3 V and
fVCO = 400 MHz):
tSK(PP)=[–50 ps...150 ps] + [–150 ps...150 ps] +
[(17ps · –3)...(17ps ·3)] + tPD, LINE(FB)
tSK(PP)=[–251 ps...351 ps] + tPD, LINE(FB)
LOW VOLTAGE PLL CLOCK DRIVER
250
Figure 5. Maximum I/O Jitter (RMS)
versus Frequency for VCC = 2.5 V
tJIT(ý) [ps] ms
Any QDevice 2
225
8
REVISION 7 3/14/16
MPC9351 DATA SHEET
This technique draws a fairly high level of DC current and
thus only a single terminated line can be driven by each
output of the MPC9351 clock driver. For the series terminated
case, however, there is no DC current draw, thus the outputs
can drive multiple series terminated lines. Figure 8 illustrates
an output driving a single series terminated line versus two
series terminated lines in parallel. When taken to its extreme,
the fanout of the MPC9351 clock driver is effectively doubled
due to its capability to drive multiple lines.
the 100 kHz to 20MHz range; therefore, the filter should be
designed to target this range. The key parameter that needs
to be met in the final filter design is the DC voltage drop
across the series filter resistor (RF). From the data sheet, the
ICCA current (the current sourced through the VCCA pin) is
typically 3mA (5mA maximum), assuming that a minimum of
2.325V (VCC = 3.3V or VCC = 2.5V) must be maintained on
the VCCA pin. The resistor RF shown in Figure 7 must have a
resistance of 270 (VCC = 3.3 V) or 9–10 (VCC = 2.5 V) to
meet the voltage drop criteria.
RF = 270 for VCC = 3.3 V
RF = 9–10 for VCC = 2.5 V
RF
VCC
MPC9351
Output
Buffer
CF = 1 F for VCC = 3.3 V
CF = 22 F for VCC = 2.5 V
VCCA
CF
10 nF
IN
14
ZO = 50
RS = 36
ZO = 50
RS = 36
ZO = 50
OutA
MPC9351
MPC9351
Output
Buffer
VCC
33...100 nF
IN
The minimum values for RF and the filter capacitor CF are
defined by the required filter characteristics. The RC filter
should provide an attenuation greater than 40 dB for noise
whose spectral content is above 100 kHz. In the example RC
filter shown in Figure 7, the filter cut-off frequency is around
3–5 kHz, and the noise attenuation at 100 kHz is better than
42dB.
As the noise frequency crosses the series resonant point
of an individual capacitor, its overall impedance begins to
look inductive, and thus, increases with increasing frequency.
The parallel capacitor combination shown ensures that a low
impedance path to ground exists for frequencies well above
the bandwidth of the PLL. Although the MPC9351 has
several design features to minimize the susceptibility to
power supply noise (isolated power and grounds and fully
differential PLL), there still may be applications in which
overall performance is being degraded due to system power
supply noise. The power supply filter schemes discussed in
this section should be adequate to eliminate power supply
noise related problems in most designs.
OutB0
14
Figure 7. VCCA Power Supply Filter
OutB1
Figure 8. Single versus Dual Transmission Lines
The waveform plots in Figure 9 show the simulation
results of an output driving a single line versus two lines. In
both cases, the drive capability of the MPC9351 output buffer
is more than sufficient to drive 50 transmission lines on the
incident edge. Note from the delay measurements in the
simulations, a delta of only 43ps exists between the two
differently loaded outputs. This suggests that dual line driving
need not be used exclusively to maintain the tight
output-to-output skew of the MPC9351. The output waveform
in Figure 9 shows a step in the waveform. This step is caused
by the impedance mismatch seen looking into the driver. The
parallel combination of the 36 series resistor plus the output
impedance does not match the parallel combination of the
line impedances. The voltage wave launched down the two
lines will equal:
VL = VS (Z0 (RS + R0 + Z0))
Driving Transmission Lines
The MPC9351 clock driver was designed to drive highspeed signals in a terminated transmission line environment.
To provide the optimum flexibility to the user, the output
drivers were designed to exhibit the lowest impedance
possible. With an output impedance of less than 20 the
drivers can drive either parallel or series terminated
transmission lines. For more information on transmission
lines the reader is referred to Freescale application note
AN1091. In most high performance clock networks,
point-to-point distribution of signals is the method of choice.
In a point-to-point scheme, either series terminated or parallel
terminated transmission lines can be used. The parallel
technique terminates the signal at the end of the line with a
50 resistance to VCC 2.
REVISION 7 3/14/16
RS = 36
Z0 = 50 || 50
RS = 36 || 36
R0 = 14
VL = 3.0 (25 (18 + 17 + 25)
= 1.31 V
At the load end, the voltage will double, due to the near
unity reflection coefficient, to 2.6V. It will then increment
towards the quiescent 3.0V in steps separated by one round
trip delay (in this case 4.0ns).
9
©2016 INTEGRATED DEVICE TECHNOLOGY, INC.
MPC9351 DATA SHEET
Since this step is well above the threshold region it will not
cause any false clock triggering; however, designers may be
uncomfortable with unwanted reflections on the line. To better
match the impedances when driving multiple lines, the
situation in Figure 10 should be used. In this case, the series
terminating resistors are reduced such that when the parallel
combination is added to the output buffer impedance, the line
impedance is perfectly matched.
3.0
2.5
OutA
tD = 3.8956
OutB
tD = 3.9386
Voltage (V)
2.0
In
1.5
MPC9351
Output
Buffer
1.0
RS = 22
ZO = 50
RS = 22
ZO = 50
14
0.5
0
2 9. Single
4
6
8
10
12
Figure
versus
Dual
Waveforms
14
14 + 22 || 22 = 50 || 50
25 = 25
Figure 10. Optimized Dual Line Termination
MPC9351 DUT
Pulse
Generator
Z = 50
ZO = 50
ZO = 50
RT = 50
RT = 50
VTT
VTT
Figure 11. CLK MPC9351 AC Test Reference for VCC = 3.3 V and VCC = 2.5 V
Differential Pulse
Generator
Z = 50
ZO = 50
MPC9351 DUT
ZO = 50
RT = 50
RT = 50
VTT
VTT
Figure 12. PCLK MPC9351 AC Test Reference
LOW VOLTAGE PLL CLOCK DRIVER
10
REVISION 7 3/14/16
MPC9351 DATA SHEET
VCC
PCLK
VCC 2
TCLK
VCMR
VCMR
PCLK
GND
VCC
VCC 2
Ext_FB
VCC
VCC 2
Ext_FB
GND
GND
t()
t()
Figure 13. Propagation Delay (tPD, static phase offset)
Test Reference
Figure 14. Propagation Delay (tPD) Test Reference
VCC
VCC 2
VCC
VCC 2
GND
GND
tP
VCC
VCC 2
T0
GND
DC = tP/T0 x 100%
tSK(O)
The time from the PLL controlled edge to the non-controlled
edge, divided by the time between PLL controlled edges,
expressed as a percentage.
The pin-to-pin skew is defined as the worst case difference
in propagation delay between any similar delay path within a
single device.
Figure 15. Output Duty Cycle (DC)
Figure 16. Output-to-Output Skew tSK(O)
TN
TN+1
TJIT(CC) = |TN–TN+1|
T0
TJIT(PER) = |TN–1/f0|
The deviation in cycle time of a signal with respect to the ideal
period over a random sample of cycle.s
The variation in cycle time of a signal between adjacent cycles,
over a random sample of adjacent cycle pairs.
Figure 17. Cycle-to-Cycle Jitter
Figure 18. Period Jitter
TCLK
(CLK)
VCC = 3.3 V
Ext_FB
tF
TJIT() = |T0–T1mean|
The deviation in t0 for a controlled edge with respect to a t0 mean
in a random sample of cycles.
VCC = 2.5 V
2.4
1.8 V
0.55
0.6 V
tR
Figure 20. Transition Time Test Reference
Figure 19. I/O Jitter
REVISION 7 3/14/16
11
©2016 INTEGRATED DEVICE TECHNOLOGY, INC.
MPC9351 Data Sheet
LOW VOLTAGE PLL CLOCK DRIVER
PACKAGE DIMENSIONS
4X
0.20 H
6
A-B D
D1
PIN 1 INDEX
3
e/2
D1/2
32
A, B, D
25
1
E1/2 A
F
B
6 E1
E
4
F
DETAIL G
8
17
9
7
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES PER
ASME Y14.5M, 1994.
3. DATUMS A, B, AND D TO BE DETERMINED AT
DATUM PLANE H.
4. DIMENSIONS D AND E TO BE DETERMINED AT
SEATING PLANE C.
5. DIMENSION b DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL NOT CAUSE THE LEAD WIDTH TO EXCEED
THE MAXIMUM b DIMENSION BY MORE THAN
0.08-mm. DAMBAR CANNOT BE LOCATED ON THE
LOWER RADIUS OR THE FOOT. MINIMUM SPACE
BETWEEN PROTRUSION AND ADJACENT LEAD OR
PROTRUSION: 0.07-mm.
6. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS
0.25-mm PER SIDE. D1 AND E1 ARE MAXIMUM
PLASTIC BODY SIZE DIMENSIONS INCLUDING
MOLD MISMATCH.
7. EXACT SHAPE OF EACH CORNER IS OPTIONAL.
8. THESE DIMENSIONS APPLY TO THE FLAT
SECTION OF THE LEAD BETWEEN 0.1-mm AND
0.25-mm FROM THE LEAD TIP.
4
D
4X
A-B D
H
SEATING
PLANE
DETAIL G
D
D/2
0.20 C
E/2
28X
e
32X
C
0.1 C
DETAIL AD
PLATING
BASE
METAL
b1
c
c1
b
8X
(θ1˚)
0.20
R R2
A2
C A-B D
SECTION F-F
R R1
A
M
5
0.25
GAUGE PLANE
A1
(S)
L
(L1)
θ˚
DETAIL AD
8
DIM
A
A1
A2
b
b1
c
c1
D
D1
e
E
E1
L
L1
q
q1
R1
R2
S
MILLIMETERS
MIN
MAX
1.40
1.60
0.05
0.15
1.35
1.45
0.30
0.45
0.30
0.40
0.09
0.20
0.09
0.16
9.00 BSC
7.00 BSC
0.80 BSC
9.00 BSC
7.00 BSC
0.50
0.70
1.00 REF
0˚
7˚
12 REF
0.08
0.20
0.08
--0.20 REF
CASE 873A-03
ISSUE B
LQFP PLASTIC PACKAGE
MPC9351 REVISION 7 3/14/16
12
©2016 Integrated Device Technology, Inc.
MPC9351 DATA SHEET
Revision History Sheet
Rev
Table
Page
Description of Change
Date
7
1
NRND – Not Recommend for New Designs
1/7/2013
7
1
Removed replacement part from features list.
1/31/2013
7
1
Removed NRND and updated data sheet format
3/18/15
1
Product Discontinuation Notice - Last time buy expires September 7, 2016.
PDN N-16-02
3/14/16
7
REVISION 7 3/14/16
13
©2016 INTEGRATED DEVICE TECHNOLOGY, INC.
Corporate Headquarters
Sales
Tech Support
6024 Silver Creek Valley Road
San Jose, CA 95138 USA
1-800-345-7015 or 408-284-8200
Fax: 408-284-2775
www.IDT.com
email: clocks@idt.com
DISCLAIMER Integrated Device Technology, Inc. (IDT) and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in
this document, including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined
in the independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether
express or implied, including, but not limited to, the suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This
document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties.
IDT’s products are not intended for use in applications involving extreme environmental conditions or in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably
expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT.
While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or
other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications, such as
those requiring extended temperature ranges, high reliability or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any
circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments.
Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Product specification subject to change without notice. Other trademarks and service marks used herein, including protected
names, logos and designs, are the property of IDT or their respective third party owners.
Copyright ©2016 Integrated Device Technology, Inc.. All rights reserved.
IMPORTANT NOTICE AND DISCLAIMER
RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL
SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING
REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND
OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible
for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3)
ensuring your application meets applicable standards, and any other safety, security, or other requirements. These
resources are subject to change without notice. Renesas grants you permission to use these resources only for
development of an application that uses Renesas products. Other reproduction or use of these resources is strictly
prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property.
Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims,
damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject
to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources
expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
(Rev.1.0 Mar 2020)
Corporate Headquarters
Contact Information
TOYOSU FORESIA, 3-2-24 Toyosu,
Koto-ku, Tokyo 135-0061, Japan
www.renesas.com
For further information on a product, technology, the most
up-to-date version of a document, or your nearest sales
office, please visit:
www.renesas.com/contact/
Trademarks
Renesas and the Renesas logo are trademarks of Renesas
Electronics Corporation. All trademarks and registered
trademarks are the property of their respective owners.
© 2020 Renesas Electronics Corporation. All rights reserved.