EML17T2R

EML17 Transistors General purpose transistor (isolated transistor and diode) EML17 DTA144E and a RB520G-30 are housed independently in a EMT package. zExternal dimensions (Unit : mm) zApplications DC / DC converter Motor driver EML17 1.6 0.5 1.0 0.5 0.5 (5) (4) 1.6 1.2 zFeatures 1) Tr : Degital Transistor Di : Low VF 2) Small package 1pin mark (1) (2) (3) 0.22 0.13 Each lead has same dimensions zStructure Silicon epitaxial planar degital transistor Schottky barrier diode zEquivalent circuit (5) (4) Tr2 Di1 R1 R2 (1) (2) (3) R1=R2=47kΩ zPackaging specifications Type EML17 Package EMT5 Marking L17 Code T2R Basic ordering unit (pieces) 8000 1/3 EML17 Transistors zAbsolute maximum ratings (Ta=25°C) Di1 Parameter Symbol Limits VR 30 DC current voltage IO 100 Mean rectifying current 500 Forward peak surge current (60HZ 1cyc.) IFSM Tj 125 Junction temperature Tstg −40 to +125 Storage temperature ∗ 60Hz, 1 Unit V mA mA °C °C Tr2 Parameter Supply voltage Input voltage Output current Power dissipation Junction temperature Symbol VCC VIN IO IC(MAX) Pd Tj Limits −50 −40 to +10 −30 −100 120 150 Unit V V mA mW °C Di1, Tr2 Parameter Symbol Pd Power dissipation Tstg Range of storage temperature Limits 150 −55 to +125 Unit mW °C ∗ ∗ Each terminal mounted on a recommended land. zElectrical characteristics (Ta=25°C) Di1 Parameter Symbol Min. Typ. Max. Unit VF IR − − − − 0.45 0.5 V µA IF=10mA VR=10V Symbol VI(off) VI(on) VO(on) II IO(off) G1 R1 R2/R1 fT Min. − −3.0 − − − 68 32.9 0.8 − Typ. − − −0.1 − − − 47 1 250 Max. −0.5 − −0.3 −0.18 −0.5 − 61.1 1.2 − Unit Conditions IC= −5V, IO= −100µA VO= −0.3V, IO= −2mA IO/II= −10mA/ −0.5mA VI= −5V VCC= −50V, VI=0V VO= −5V, IO= −5mA − − VCE= −10V, IE=5mA, f=100MHz Forward voltage Reverse current Conditions ∗ Please pay attention to static electricity when handling. Tr2 Parameter Input voltage Output voltage Input current Output current DC current gain Input resistance Resistance ratio Transition frequency V V mA µA − kΩ − MHz ∗ ∗ Transition frequency of the device 2/3 EML17 Transistors CAPACITANCE BETWEEN TERMINALS : CT (pF) zElectrical characteristic curves Di1 1000000 1000 150 C 100000 REVERSE CURRENT : IR (nA) FORWARD CURRENT : IF (mA) 100 150 C −25 C 10 25 C 1 75 C 125 C 0.1 0.01 0.001 0 100 200 300 400 500 600 125 C 10000 75 C 1000 100 25 C 10 −25 C 1 0 700 10 20 30 100 10 1 0 40 10 15 20 25 30 Fig. 3 Capacitance between terminals characteristics Fig.2 Reverse characteristics Fig.1 Forward characteristics 5 REVERSE VOLTAGE : VR (V) REVERSE VOLTAGE : VR (V) FORWARD VOLTAGE : VF (mV) Tr2 OUTPUT CURRENT : Io (A) INPUT VOLTAGE : VI(on) (V) −20 −10 −5 Ta=−40°C 25°C 100°C −2 −1 −500m −200m −100m −100µ −200µ −500µ −1m −2m −5m −10m −20m −50m−100m OUTPUT CURRENT : IO (A) Fig.4 Input voltage vs. output current (ON characteristics) OUTPUT VOLTAGE : VO(on) (V) −1 −500m −200m −10m VCC=−5V −5m VO=−0.3V −50 −2m −1m −500µ 1k Ta=100°C 25°C −40°C −200µ −100µ −50µ −20µ −10µ −5µ −2µ −1µ 0 VO=−5V 500 DC CURRENT GAIN : GI −100 200 100 Ta=100°C 25°C −40°C 50 20 10 5 2 −0.5 −1.0 −1.5 −2.0 −2.5 −3.0 INPUT VOLTAGE : VI(off) (V) Fig.5 Output current vs. Input voltage (OFF characteristics) 1 −100µ −200µ −500µ −1m −2m −5m −10m −20m −50m−100m OUTPUT CURRENT : IO (A) Fig.6 DC current gain vs. output current lO/lI=20 Ta=100°C 25°C −40°C −100m −50m −20m −10m −5m −2m −1m −100µ −200µ -−500µ −1m −2m −5m −10m −20m −50m−100m OUTPUT CURRENT : IO (A) Fig.7 Output voltage vs. output current 3/3 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1