6EP1331-1SH03

Siemens Industry Online Support - Automation Service, Automation Su... 1 of 3 https://support.automation.siemens.com/WW/llisapi.dll?func=ll&objId... Automation Technology > Power supplies > Power supply SITOP > LOGO!Power 6EP1331-1SH03 LOGO!POWER 24 V/1,3 A Technical / CAx data Technical Data CAx data LOGO!POWER 24 V STABILIZED POWER SUPPLY INPUT: 100-240 V AC (110-300 V DC) OUTPUT: 24 V/1.3 A DC Technical specifications Product LOGO!Power Power supply, type 24 V/1.3 A Input Input 1-phase AC or DC Rated voltage value Vin rated 100…240 V Voltage range 85…264 V Input voltage / at DC 110…300 V Wide-range input Yes Overvoltage resistance 2.3 × Vin rated, 1.3 ms Mains buffering at Iout rated, min. 40 ms Mains buffering at Vin = 187 V Rated line frequency 50/60 Hz Rated line range 47...63 Hz Input current / at nominal level of the input voltage 120 V 0.7 A Input current / at nominal level of the input voltage 230 V 0.35 A Switch-on current limiting (+25 °C), max. 25 A I²t, max. 0.8 A²·s Built-in incoming fuse internal Protection in the mains power input (IEC 898) Recommended miniature circuit breaker: from 16 A, characteristic B or from 10 A, characteristic C Output Output Controlled, isolated DC voltage Rated voltage Vout DC 24 V Total tolerance, static ± 3% Static mains compensation, approx. 0.1 % Static load balancing, approx. 1.5 % 24/05/2013 09:53 Siemens Industry Online Support - Automation Service, Automation Su... 2 of 3 https://support.automation.siemens.com/WW/llisapi.dll?func=ll&objId... Residual ripple peak-peak, max. 200 mV Residual ripple peak-peak, typ. 10 mV Spikes peak-peak, max. (bandwidth: 20 MHz) 300 mV Spikes peak-peak, typ. (bandwidth: 20 MHz) 20 mV Adjustment range 22.2…26.4 V Product feature / output voltage adjustable Yes Output voltage setting via potentiometer Status display Green LED for output voltage OK On/off behavior No overshoot of Vout (soft start) Startup delay, max. 0.5 s Voltage rise, typ. 15 ms Rated current value Iout rated 1.3 A Current range 0…1.3 A Note 1.3 A up to +55 °C, 0.9 A up to +70 °C delivered active power / typ. 30 W Parallel switching for enhanced performance Yes Numbers of parallel switchable units for enhanced performance 2 Efficiency Efficiency at Vout rated, Iout rated, approx. 85 % Power loss at Vout rated, Iout rated, approx. 6W Closed-loop control Dynamic mains compensation (Vin rated ±15 %), max. 0.2 % Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ. 1 % Load step setting time 10 to 90%, typ. 1 ms Load step setting time 90 to 10%, typ. 1 ms Protection and monitoring Output overvoltage protection Yes, according to EN 60950 Current limitation, typ. 1.7 A Characteristic feature of the output / short-circuit protected Yes Short-circuit protection Constant current characteristic Enduring short circuit current / Effective level / maximum 2.4 A Overload/short-circuit indicator - Safety Primary/secondary isolation Yes Potential separation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 Protection class Class II (without protective conductor) CE mark Yes UL/CSA approval Yes UL/cUL (CSA) approval cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cURusRecognized (UL 60950, CSA C22.2 No. 60950), File E151273, NEC class 2 (UL 1310) Explosion protection ATEX (EX) II 3G Ex nA IIC T3; cCSAus (CSA C22.2 No. 213-M1987, ANSI/ISA12.12.01-2007) Class I, Div. 2, Group ABCD, T4 FM approval Class I, Div. 2, Group ABCD, T4 CB approval Yes 24/05/2013 09:53 Siemens Industry Online Support - Automation Service, Automation Su... 3 of 3 https://support.automation.siemens.com/WW/llisapi.dll?func=ll&objId... Marine approval GL, ABS, DNV, LRS (BV in process) Degree of protection (EN 60529) IP20 EMC Emitted interference EN 55022 Class B Supply harmonics limitation not applicable Noise immunity EN 61000-6-2 Operating data Ambient temperature / in operation Note -20…+70 °C with natural convection Ambient temparature / on transport -40…+85 °C Ambient temparature / in storage -40…+85 °C Humidity class according to EN 60721 Climate class 3K3, no condensation Mechanics Connection technology screw-type terminals Connections / Supply input L, N: 1 screw terminal each for 0.5 ... 2.5 mm2 single-core/finely stranded Connections / Output +, -: 2 screw terminals each for 0.5 ... 2.5 mm² Connections / Auxiliary - Width / of the housing 54 mm Height / of the housing 90 mm Depth / of the housing 55 mm Installation width 54 mm Mounting height 130 mm Weight, approx. 0.17 kg Product feature / of the housing / housing for side-by-side mounting Yes Type of mounting / wall mounting No Type of fixing / cap rail mounting Yes Type of mounting / S7-300 rail mounting No Installation Snaps onto DIN rail EN 60715 35x7.5/15 Other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) letzte Änderung: Mar 22, 2013 © Siemens AG 2013 - Corporate Information - Privacy Policy - Terms of Use 24/05/2013 09:53