6EP1332-1SH43

Product data sheet 6EP1332-1SH43 LOGO!POWER 24 V STABILIZED POWER SUPPLY INPUT: 100-240 V AC (110-300 V DC) OUTPUT: 24 V/2.5 A DC Technical specifications Product LOGO!Power Power supply, type 24 V/2.5 A Input Input 1-phase AC or DC Rated voltage value Vin rated 100 … 240 V Voltage range 85 … 264 V Input voltage / at DC 110 … 300 V Wide-range input Yes Overvoltage resistance 2.3 × Vin rated, 1.3 ms Mains buffering at Iout rated, min. 40 ms Mains buffering at Vin = 187 V Rated line frequency 50 / 60 Hz Rated line range 47 ... 63 Hz Input current / at nominal level of the input voltage 120 V 1.22 A Input current / at nominal level of the input voltage 230 V 0.66 A Switch-on current limiting (+25 °C), max. 46 A I²t, max. 3 A²·s Built-in incoming fuse internal Protection in the mains power input (IEC 898) Recommended miniature circuit breaker: from 16 A, characteristic B or from 10 A, characteristic C 6EP1332-1SH43 Page 1/ 4 10/22/2012 subject to modifications © Copyright Siemens AG 2012 Output Output Controlled, isolated DC voltage Rated voltage Vout DC 24 V Total tolerance, static ± 3% Static mains compensation, approx. 0.1 % Static load balancing, approx. 1.5 % Residual ripple peak-peak, max. 200 mV Residual ripple peak-peak, typ. 10 mV Spikes peak-peak, max. (bandwidth: 20 MHz) 300 mV Spikes peak-peak, typ. (bandwidth: 20 MHz) 50 mV Adjustment range 22.2 … 26.4 V Product feature / output voltage adjustable Yes Output voltage setting via potentiometer Status display Green LED for output voltage OK On/off behavior No overshoot of Vout (soft start) Startup delay, max. 0.5 s Voltage rise, typ. 10 ms Rated current value Iout rated 2.5 A Current range 0 … 2.5 A • Note 2.5 A up to +55 °C, 1.7 A up to +70 °C delivered active power / typ. 60 W Parallel switching for enhanced performance Yes Numbers of parallel switchable units for enhanced performance 2 Efficiency Efficiency at Vout rated, Iout rated, approx. 88 % Power loss at Vout rated, Iout rated, approx. 8W Closed-loop control Dynamic mains compensation (Vin rated ±15 %), max. 0.2 % Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ. 2% Load step setting time 10 to 90%, typ. 1 ms Load step setting time 90 to 10%, typ. 1 ms Protection and monitoring Output overvoltage protection Yes, according to EN 60950 Current limitation, typ. 3.3 A Characteristic feature of the output / short-circuit protected Yes Short-circuit protection Constant current characteristic Enduring short circuit current / Effective level / maximum 4.8 A Overload/short-circuit indicator - Safety 6EP1332-1SH43 Page 2/ 4 10/22/2012 subject to modifications © Copyright Siemens AG 2012 Primary/secondary isolation Yes Potential separation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 Protection class Class II (without protective conductor) CE mark Yes UL/CSA approval Yes UL/cUL (CSA) approval cULus-listed (UL 508, CSA C22.2 No. 107.1), File E197259; cURusrecognized (UL 60950, CSA C22.2 No. 60950), File E151273 Explosion protection ATEX (EX) II 3G Ex nA IIC T3; cCSAus (CSA E60079, UL 60079), Class I, Div. 2, Group ABCD, T4 FM approval Class I, Div. 2, Group ABCD, T4 CB approval Yes Marine approval GL, ABS, DNV, LRS (BV in process) Degree of protection (EN 60529) IP20 EMC Emitted interference EN 55022 Class B Supply harmonics limitation not applicable Noise immunity EN 61000-6-2 Operating data Ambient temperature / in operation -20 … +70 °C • Note with natural convection Ambient temparature / on transport -40 … +85 °C Ambient temparature / in storage -40 … +85 °C Humidity class according to EN 60721 Climate class 3K3, no condensation Mechanics Connection technology screw-type terminals Connections / Supply input L, N: 1 screw terminal each for 0.5 ... 2.5 mm2 single-core/finely stranded Connections / Output +, -: 2 screw terminals each for 0.5 ... 2.5 mm² Connections / Auxiliary - Width / of the housing 72 mm Height / of the housing 90 mm Depth / of the housing 55 mm Installation width 72 mm Mounting height 130 mm Weight, approx. 0.25 kg Product feature / of the housing / housing for side-by-side mounting Yes Type of mounting / wall mounting No Type of fixing / cap rail mounting Yes Type of mounting / S7-300 rail mounting No 6EP1332-1SH43 Page 3/ 4 10/22/2012 subject to modifications © Copyright Siemens AG 2012 Installation Snaps onto DIN rail EN 60715 35x7.5/15 Other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) letzte Änderung: Oct 19, 2012 6EP1332-1SH43 Page 4/ 4 10/22/2012 subject to modifications © Copyright Siemens AG 2012