DSL05-008SC6

DSL05 Secondary protection for VDSL2 and G.FAST lines Datasheet - production data Description DSL05 is designed to protect DSL line drivers against surges defined in worldwide telecommunication standards. This device protects line drivers of various systems such as xDSL and G.FAST. The low capacitance makes it suitable from ADSL to G.FAST data rates. DSL05 is able to survive severe conditions even when used with downgraded or oscillating gas tube. SOT23-6L This device is packaged in a SOT23-6L. Figure 1: Functional diagram Features       High surge capability to comply with GR-1089 and ITU-T K20/21/45 Keeps peak power capability at high temperature Voltages: 8, 12, 16 and 24 V Low capacitance device: Ctyp = 0.95 pF RoHS package Low leakage current: 50 nA at 25 °C I/O1 NC -VLD +VLD I/O2 NC Complies with the following standards Refer to Section 2: "Schematics".      Telcordia GR-1089  2.5 kV 2/10 μs - 500 A 2/10 μs  AC power fault tests ITU-T K20/21/45  6 kV 10/700 μs - 150 A 5/310 μs  power induction and contact tests IEC 61000-4-2, level 4  15 kV (air discharge)  8 kV (contact discharge) IEC 61000-4-5, level 2  1 kV, 42 Ω MIL STD 883G-Method 3015-7: Class 3  8 kV (human body model) August 2017 Table 1: Device summary Order code VRM(V) DSL05-008SC6 8 DSL05-012SC6 12 DSL05-016SC6 16 DSL05-024SC6 24 DocID029116 Rev 3 This is information on a product in full production. 1/10 www.st.com Characteristics 1 DSL05 Characteristics Table 2: Absolute ratings (Tamb = -40 to 85 °C) Symbol Ipp Parameter Value 8/20μs Peak pulse current dl/dt Critical rate of on-state current rise Tstg Storage junction temperature range Tj Maximum operating junction temperature TL Maximum temperature for soldering during 10 s Unit 30 A 1000 A/µs -55 to +150 °C 260 °C Table 3: Electrical characteristics (Tamb = 25 °C, pin 1 to pin 3) VBR at 1 mA VBO IH C(1) ΔC(2) Min. Max. Typ. Max. Typ. V V V mA pF pF IRM at VRM Typ. Max. Typ. Max. Order code Tamb = 85 °C nA DSL05-008SC6 0.1 50 7 100 8 9.5 15 50 1.5 0.25 DSL05-012SC6 0.1 50 7 100 12 12.8 18 10 1.5 0.25 DSL05-016SC6 0.1 50 7 100 16 18 25 30 1.5 0.25 DSL05-024SC6 0.1 50 7 100 24 25.5 31 50 1.5 0.25 Notes: (1)Test conditions: VR = 2 V bias, VRMS = 1 V, f = 1 MHz (2)Measured between 1 V and VRM Figure 2: Electrical characteristics definitions 2/10 DocID029116 Rev 3 DSL05 Characteristics 1.1 Characteristics (curves) Figure 3: Peak pulse power dissipation versus initial junction temperature (maximum values) Figure 4: Leakage current versus junction temperature IPP (A) 50 8/20 µs 40 30 20 10 T j(°C) 0 0 25 50 75 100 125 150 175 Figure 5: Junction capacitance versus reverse voltage 3 Figure 6: Junction capacitance versus junction temperature C(pF) 1.6 T j = 25 °C Vosc = 1 V V R < V RM I/O to I/O 2.5 C(pF) V osc = 1 V V R= 2 V I/O to I/O 1.5 1.4 1.3 2 1.2 1.1 1.5 1.0 1 0.9 0.8 0.5 0.7 T j(°C) V R(V) 0.6 0 0 2 4 6 8 10 12 14 16 18 20 22 24 0 25 50 75 100 125 Figure 7: Clamping response to 8/20 µs surge (Ipp = 10 A) DocID029116 Rev 3 3/10 150 Schematics 2 DSL05 Schematics Figure 8: xDSL and G.FAST schematic for CPE applications VLD+ VLD- VLD+ VLD- Figure 9: xDSL and G.FAST schematic for infrastructure applications VLD+ VLD- VLD+ VLD- On topologies given in Figure 8: "xDSL and G.FAST schematic for CPE applications" and Figure 9: "xDSL and G.FAST schematic for infrastructure applications", +VLD and -VLD may not be connected. 4/10 DocID029116 Rev 3 DSL05 3 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark.   3.1 Epoxy meets UL 94,V0 Lead-free package SOT23-6L package information Figure 10: SOT23-6L package outline Table 4: SOT23-6L package mechanical data Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A 0.9 1.45 0.0354 0.0571 A1 0 0.15 0 0.0059 A2 0.9 1.3 0.0354 0.0512 b 0.30 0.5 0.0118 0.0197 c 0.09 0.2 0.0035 0.0079 D 2.8 3.05 0.1102 0.1201 E 1.5 1.75 0.0591 0.0689 e 0.95 0.0374 H 2.6 3 0.1024 0.1181 L 0.3 0.6 0.0118 0.0236 θ 0 10 0 0.3937 DocID029116 Rev 3 5/10 Package information DSL05 Figure 11: Footprint recommendations, dimensions in mm (inches) 6/10 Figure 12: Marking layout (refer to ordering information table for marking) Figure 13: Package orientation in reel Figure 14: Tape and reel orientation Figure 15: Reel dimensions (mm) Figure 16: Inner box dimensions (mm) DocID029116 Rev 3 DSL05 Package information Figure 17: Tape and reel outline Table 5: Tape and reel mechanical data Dimensions Ref. P1 Millimeters Min. Typ. Max. 3.9 4 4.1 P0 3.9 4 4.1 D0 1.45 1.5 1.6 D1 1 F 3.45 3.5 3.55 K0 1.3 1.4 1.6 P2 1.95 2 2.05 W 7.9 8 8.3 DocID029116 Rev 3 7/10 Package information DSL05 Figure 18: ST ECOPACK® recommended soldering reflow profile for PCB mounting Minimize air convection currents in the reflow oven to avoid component movement. Maximum soldering profile corresponds to the latest IPC/JEDEC J-STD-020. 8/10 DocID029116 Rev 3 DSL05 4 Ordering information Ordering information Figure 19: Ordering information scheme DSL 0x - vvv SC6 DSL protection Version Stand-off voltage 024 = 24 V Package SC6 = SOT23-6L Table 6: Ordering information 5 Order code Marking DSL05-008SC6 D508 DSL05-012SC6 D512 DSL05-016SC6 D516 DSL05-024SC6 D524 Package Weight Base qty. Delivery mode SOT23-6L 14 g 3000 Tape and reel Revision history Table 7: Document revision history Date Revision 05-Jul-2016 1 Initial release. 03-Oct-2016 2 Updated Table 3: "Electrical characteristics (Tamb = 25 °C, pin 1 to pin 3)". 3 Added RPN DSL05-016SC6. Updated Table 3: "Electrical characteristics (Tamb = 25 °C, pin 1 to pin 3)" and Figure 4: "Leakage current versus junction temperature". 22-Aug-2017 Changes DocID029116 Rev 3 9/10 DSL05 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2017 STMicroelectronics – All rights reserved 10/10 DocID029116 Rev 3