M74HC14YTTR

M74HC14 Hex Schmitt inverter Datasheet - production data Description The M74HC14 is a high speed CMOS hex Schmitt inverter fabricated with silicon gate 2 C MOS technology. Pin configuration and functions are the same as those of the M74HC04 but all inputs have a 20 % VCC hysteresis level. This, together with the Schmitt trigger function, allows the device to be used on line receivers with slow rise/fall input signals. All inputs are equipped with protection circuits against static discharge and transient excess voltage. Features High speed: tPD = 12 ns (typ.) at VCC = 6 V Low power dissipation: ICC = 1 μA (max.) at TA = 25 °C High noise immunity: VH = 1.2 V (typ.) at VCC = 6 V Symmetrical output impedance: |IOH| = IOL = 4 mA (min.) Balanced propagation delays: tPLH ≃ tPHL Wide operating voltage range: VCC (opr) = 2 to 6 V Pin and function compatible with 74 series 14 ESD performance CDM: 1 kV HBM: 2 kV MM: 200 V February 2016 DocID1901 Rev 5 This is information on a product in full production. 1/15 www.st.com Contents M74HC14 Contents 1 Pin information ................................................................................ 3 2 Functional description .................................................................... 4 3 4 Electrical characteristics ................................................................ 5 Package information ....................................................................... 8 4.1 SO14 package information ................................................................ 9 4.2 SO14 tape and reel package information ........................................ 10 4.3 TSSOP14 package information ....................................................... 11 4.4 TSSOP14 tape and reel package information ................................. 12 5 Ordering information..................................................................... 13 6 Revision history ............................................................................ 14 2/15 DocID1901 Rev 5 M74HC14 1 Pin information Pin information Figure 1: Pin connections and IEC logic symbols Table 1: Pin description Pin number Symbol Name and function 1, 3, 5, 9, 11, 13 1A to 6A Data inputs 2, 4, 6, 8, 10, 12 1Y to 6Y Data outputs 7 GND Ground (0 V) 14 VCC Positive supply voltage DocID1901 Rev 5 3/15 Functional description 2 M74HC14 Functional description Table 2: Truth table A Y L H H L Figure 2: Input and output equivalent circuit 4/15 DocID1901 Rev 5 M74HC14 3 Electrical characteristics Electrical characteristics Stressing the device above the ratings listed in the “Absolute maximum ratings” table may cause permanent damage to the device. These are stress ratings only, and operation of the device at these or any other conditions above those indicated in the operating sections of this specification are not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Please refer to the STMicroelectronics SURE program and other relevant quality documents. Table 3: Absolute maximum ratings Symbol VCC Parameter Supply voltage Unit -0.5 to 7 VI DC input voltage VO DC output voltage IIK DC input diode current IOK DC output diode current IO DC output current ICC or IGND Value -0.5 to VCC + 0.5 ±20 ±25 DC VCC or ground current PD Power dissipation Tstg Storage temperature TL Lead temperature (10 s) V mA ±50 500 (1) -65 to 150 300 mW °C Notes: (1) 500 mW at 65 °C; derate to 300 mW by 10 mW/°C from 65 °C to 85 °C Table 4: Recommended operating conditions Symbol VCC Parameter Supply voltage VI Input voltage VO Output voltage Toper Operating temperature DocID1901 Rev 5 Value Unit 2 to 6 0 to VCC -55 to 125 V °C 5/15 Electrical characteristics M74HC14 Table 5: DC specification Test condition Sym Vt+ Vt- Parameter Low-level input voltage Hysteresis voltage VOH Typ Max Min Max Min Max 2.0 1.0 1.28 1.5 1.0 1.5 1.0 1.5 4.5 2.3 2.8 3.15 2.3 3.15 2.3 3.15 6.0 3.0 3.7 4.2 3.0 4.2 3.0 4.2 2.0 0.3 0.74 0.9 0.3 0.9 0.3 0.9 4.5 1.13 1.8 2.0 1.13 2.0 1.13 2.0 6.0 1.5 2.4 2.6 1.5 2.6 1.5 2.6 2.0 0.3 0.54 1.0 0.3 1.0 0.3 1.0 4.5 0.6 1.0 1.4 0.6 1.4 0.6 1.4 6.0 0.8 1.3 1.4 0.8 1.7 0.8 1.7 2.0 1.9 2.0 1.9 1.9 4.4 4.5 4.4 4.4 5.9 6.0 5.9 5.9 IO = -20 µA 6.0 4.5 IO = -4.0 mA 4.18 4.31 4.13 4.10 6.0 IO = -5.2 mA 5.68 5.8 5.63 5.60 2.0 4.5 Low-level output voltage VOL II IO = -20 µA 6.0 Quiescent supply current Unit V 0.0 0.1 0.1 0.1 0.0 0.1 0.1 0.1 0.0 0.1 0.1 0.1 4.5 IO = -4.0 mA 0.17 0.26 0.33 0.40 6.0 IO = -5.2 mA 0.18 0.26 0.33 0.40 ±0.1 ±1 ±1 6.0 VI = VCC or GND 1 10 20 Input leakage current ICC -55 to 125 °C Min 4.5 High-level output voltage -40 to 85 °C TA = 25 °C VCC (V) High-level input voltage VH Value µA Table 6: AC electrical characteristics (CL = 50 pF, input tr = tf = 6 ns) Test condition Sym. tTLH, tTHL Parameter Output transition time VCC (V) Value TA = 25 °C -40 to 85 °C -55 to 125 °C Typ Max Max Max 2.0 30 75 95 110 4.5 8 15 19 22 6.0 7 13 16 19 2.0 42 125 155 190 4.5 14 25 31 38 6.0 12 21 16 32 Value ns tPLH, tPHL 6/15 Propagation delay time DocID1901 Rev 5 M74HC14 Electrical characteristics Table 7: Capacitive characteristics Test condition Sym. CIN CPD Parameter TA = 25 °C VCC (V) Input capacitance Power dissipation capacitance (1) Value -40 to 85 °C -55 to 125 °C Typ Max Max Max 5 10 10 10 5.0 Value pF fIN = 10 MHz 28 Notes: (1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load (refer to test circuit). Average operating current can be obtained by the following equation: ICC(opr) = CPD x VCC x fIN + ICC/6(per gate) Figure 3: Test circuit Figure 4: Waveform: propagation delay times (f = 1 MHz, 50 % duty cycle) DocID1901 Rev 5 7/15 Package information 4 M74HC14 Package information In order to meet environmental requirements, ST offers these devices in different grades of ® ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ® ECOPACK is an ST trademark. 8/15 DocID1901 Rev 5 M74HC14 4.1 Package information SO14 package information Figure 5: SO14 package outline Table 8: SO14 mechanical data Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A 1.35 1.75 0.05 0.068 A1 0.10 0.25 0.004 0.009 A2 1.10 1.65 0.04 0.06 B 0.33 0.51 0.01 0.02 C 0.19 0.25 0.007 0.009 D 8.55 8.75 0.33 0.34 E 3.80 4.0 0.15 0.15 e 1.27 0.05 H 5.80 6.20 0.22 0.24 h 0.25 0.50 0.009 0.02 L 0.40 1.27 0.015 0.05 k ddd 8° (max) 0.10 DocID1901 Rev 5 0.004 9/15 Package information 4.2 M74HC14 SO14 tape and reel package information Figure 6: SO14 tape and reel package outline 1. Drawing is not to scale Table 9: SO14 tape and reel mechanical data Dimensions Ref Millimeters Min. A Max. Min. 330 13.2 Max. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 10/15 Inches 0.504 22.4 0.519 0.882 Ao 6.4 6.6 0.252 0.260 Bo 9 9.2 0.354 0.362 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 DocID1901 Rev 5 M74HC14 4.3 Package information TSSOP14 package information Figure 7: TSSOP14 package outline aaa Table 10: TSSOP14 mechanical data Dimensions Ref. Millimeters Min. Typ. A Inches Max. Min. Typ. 1.20 A1 0.05 A2 0.80 b Max. 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.90 5.00 5.10 0.193 0.197 0.201 E 6.20 6.40 6.60 0.244 0.252 0.260 E1 4.30 4.40 4.50 0.169 0.173 0.176 e L 0.65 0.45 L1 k aaa 1.00 0.60 0.0256 0.75 0.018 1.00 0° 0.024 0.030 0.039 8° 0.10 DocID1901 Rev 5 0° 8° 0.004 11/15 Package information 4.4 M74HC14 TSSOP14 tape and reel package information Figure 8: TSSOP14 tape and reel package outline 1. Drawing is not to scale Table 11: TSSOP14 tape and reel mechanical data Dimensions Ref Millimeters Min. A Max. Min. 330 13.2 Max. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 12/15 Inches 0.504 22.4 0.519 0.882 Ao 6.7 6.9 0.264 0.272 Bo 5.3 5.5 0.209 0.217 Ko 1.6 1.8 0.063 0.071 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 DocID1901 Rev 5 M74HC14 5 Ordering information Ordering information Table 12: Order codes Order code Temperature range M74HC14YRM13TR M74HC14YTTR (1) (1) Package -40 °C to 125 °C SO14 (automotive grade) -40 °C to 125 °C TSSOP14 (automotive grade) Packing Tape and reel Marking 74HC14Y 74HC14Y Notes: (1) Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 and Q002. DocID1901 Rev 5 13/15 Revision history 6 M74HC14 Revision history Table 13: Document revision history Date Revisi on 01-Jul-2001 1 Initial release. 23-May-2008 2 Document converted and restructured to new template. Removed: M74HC14M1R order code. Added: tape and reel specifications for SO-14 and TSSOP14 packages. 09-Aug-2013 3 Features: added ESD information Table 1: Device summary: added automotive grade order codes. Added Section 5: Ordering information. 13-Jan-2014 4 Removed DIP14 package Table 1: Device summary and Table 13: Order codes: added “Temperature range” and “Marking”; updated 1. 5 Removed Table 1: Device summary (same table appears in Section 5: "Ordering information"). Replaced SO14 package information TSSOP14 package information: updated max E1 parameter (mm), added L1 and aaa parameters. Replaced TSSOP14 tape and reel package outline Table 12: "Order codes": removed obsolete order codes M74HC14M13TR and M74HC14TTR; replaced the marking of order code M74HC14YTTR (74HC14Y instead of HC14Y). 17-Feb-2016 14/15 Changes DocID1901 Rev 5 M74HC14 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved DocID1901 Rev 5 15/15