STD25N10F7

STD25N10F7, STF25N10F7, STP25N10F7 N-channel 100 V, 0.027 Ω typ., 25 A, STripFET™ VII DeepGATE™ Power MOSFET in DPAK, TO-220FP and TO-220 packages Datasheet - production data Features TAB Order codes VDSS RDS(on) max.(1) STD25N10F7 100 V 0.035 Ω 25 A 40 W STF25N10F7 100 V 0.035 Ω 19 A 25 W STP25N10F7 100 V 0.035 Ω 25 A 50 W DPAK TAB ID PTOT 1. @ VGS = 10 V 3 3 2 1 1 TO-220FP 2 TO-220 • Ultra low on-resistance • 100% avalanche tested Applications Figure 1. Internal schematic diagram • Switching applications Description 'Ć7$% These devices utilize the 7th generation of design rules of ST’s proprietary STripFET™ technology, with a new gate structure. The resulting Power MOSFET exhibits the lowest RDS(on) in all packages. * 6 $0Y Table 1. Device summary Order codes Marking Package Packaging STD25N10F7 25N10F7 DPAK Tape and reel STF25N10F7 25N10F7 TO-220FP Tube STP25N10F7 25N10F7 TO-220 Tube September 2013 This is information on a product in full production. DocID025265 Rev 1 1/21 www.st.com Contents STD25N10F7, STF25N10F7, STP25N10F7 Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 Electrical characteristics (curves) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 Test circuits 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 2/21 .............................................. 9 DocID025265 Rev 1 STD25N10F7, STF25N10F7, STP25N10F7 1 Electrical ratings Electrical ratings Table 2. Absolute maximum ratings Value Symbol Parameter Unit DPAK TO-220 TO-220FP VDS Drain-source voltage 100 V VGS Gate-source voltage ± 20 V ID(1) Drain current (continuous) at TC = 25 °C 25 25 19 A ID(1) Drain current (continuous) at TC = 100 °C 18 18 13.5 A Drain current (pulsed) 100 100 76 A Total dissipation at TC = 25 °C 40 50 25 W 2500 V IDM(2) PTOT(1) VISO TJ Insulation withstand voltage (RMS) from all three leads to external heat sink (t = 1 s; TC = 25 °C) - Operating junction temperature °C -55 to 175 Tstg Storage temperature °C 1. This value is rated according to Rthj-c. 2. Pulse width limited by safe operating area. Table 3. Thermal resistance Value Symbol Parameter Rthj-case Thermal resistance junction-case Rthj-amb Thermal resistance junction-ambient Rthj-pcb Thermal resistance junction-pcb DocID025265 Rev 1 Unit DPAK TO-220FP TO-220 3.75 6 3 62.5 50 °C/W °C/W °C/W 3/21 21 Electrical characteristics 2 STD25N10F7, STF25N10F7, STP25N10F7 Electrical characteristics (TCASE = 25 °C unless otherwise specified) Table 4. On/off states Symbol Parameter Test conditions Min. Typ. Max. Unit - V Drain-source breakdown voltage (VGS= 0) ID = 250 μA IDSS Zero gate voltage drain current (VGS = 0) VDS = 100 V VDS = 100 V; TC = 125 °C 10 100 μA μA IGSS Gate body leakage current (VDS = 0) VGS = ± 20 V ±100 nA VGS(th) Gate threshold voltage VDS = VGS, ID = 250 μA 4.5 V RDS(on) Static drain-source on- resistance VGS = 10 V, ID = 12.5 A 0.027 0.035 Ω Min. Typ. Max. Unit - 920 - pF - 215 - pF - 19 - pF - 14 - nC - 7 - nC - 3 - nC V(BR)DSS 100 2.5 Table 5. Dynamic Symbol 4/21 Parameter Ciss Input capacitance Coss Output capacitance Crss Reverse transfer capacitance Qg Total gate charge Qgs Gate-source charge Qgd Gate-drain charge Test conditions VDS = 50 V, f = 1 MHz, VGS = 0 VDD = 50 V, ID = 25 A VGS = 10 V Figure 18 DocID025265 Rev 1 STD25N10F7, STF25N10F7, STP25N10F7 Electrical characteristics Table 6. Switching times Symbol td(on) tr Parameter Test conditions Turn-on delay time VDD = 50 V, ID = 12.5 A, RG = 4.7 Ω, VGS = 10 V Figure 17 Rise time td(off) tf Turn-off delay time Fall time Min. Typ. Max. Unit - 9.8 - ns - 14 - ns - 14.8 - ns - 4.6 - ns Max. Unit Table 7. Source-drain diode Symbol ISD ISDM (1) VSD(2) Parameter Test conditions Min. Typ. Source-drain current - 25 A Source-drain current (pulsed) - 100 A 1.1 V Forward on voltage ISD = 25 A, VGS = 0 - trr Reverse recovery time - 38 ns Qrr Reverse recovery charge - 29 nC IRRM Reverse recovery current ISD = 25 A, di/dt = 100 A/μs, VDD = 80 V, Tj = 150 °C - 1.7 A 1. Pulse width limited by safe operating area. 2. Pulsed: pulse duration = 300 μs, duty cycle 1.5%. DocID025265 Rev 1 5/21 21 Electrical characteristics 2.1 STD25N10F7, STF25N10F7, STP25N10F7 Electrical characteristics (curves) Figure 2. Safe operating area for DPAK AM16006v1 ID (A) Figure 3. Thermal impedance for DPAK K Tj=150°C Tc=25°C Single pulse 100 AM16024v1 δ=0.5 0.2 0.1 a is are s n) thi RDS(o in on max i t era by Op ited Lim 10 0.05 0.02 0.01 10 -1 1 100µs 0.01 0.1 1 10 10 -2 10 -6 VDS(V) Figure 4. Safe operating area for TO-220FP 10 -5 10 -4 10-3 10 -1 tp(s) Figure 5. Thermal impedance for TO-220FP K AM16025v1 δ=0.5 (o n) 0.2 0.1 100µs 0.05 0.02 0.01 Li m 10 10 -2 is AM16022v1 Tj=150°C Tc=25°C Single pulse O pe ra ite tio d n in by m this ax a RD rea S ID (A) Single pulse 1ms 10ms 0.1 10 -1 1 Single pulse 1ms 10ms 0.1 0.1 1 10 10 -2 10 -6 VDS(V) Figure 6. Safe operating area for TO-220 AM16023v1 ID (A) 100 10 10 -5 10 -4 10-3 10 -2 10 -1 tp(s) Figure 7. Thermal impedance for TO-220 K Tj=150°C Tc=25°C Single pulse AM16026v1 δ=0.5 0.2 0.1 a is are n) (o his n t x RDS i n tio y ma a r b e Op ited Lim 100µs 1ms 1 0.05 0.02 0.01 10 -1 10ms Single pulse 0.1 0.01 0.1 6/21 1 10 VDS(V) 10 -2 10 -6 DocID025265 Rev 1 10 -5 10 -4 10-3 10 -2 10 -1 tp(s) STD25N10F7, STF25N10F7, STP25N10F7 Electrical characteristics Figure 8. Output characteristics Figure 9. Transfer characteristics AM16008v1 ID (A) VGS=10V 80 AM16009v1 ID (A) 80 9V VDS=6V 70 70 8V 60 60 50 50 7V 40 40 30 30 6V 20 20 10 10 5V 0 0 1 2 3 4 5 6 7 8 0 Figure 10. Gate charge vs gate-source voltage AM16010v1 VGS (V) 12 2 VDS(V) VDD=50V ID=25A 3 4 5 7 6 8 9 10 11 VGS(V) Figure 11. Static drain-source on-resistance AM16011v1 RDS(on) (mΩ) VGS=10V 0.096 10 40.0 8 30.0 6 20.0 4 10.0 2 0.0 0 0 5 10 15 Figure 12. Capacitance variations 5 15 10 ID(A) 20 Figure 13. Normalized gate threshold voltage vs temperature AM16012v1 C (pF) 0 Qg(nC) AM16013v1 VGS(th) (norm) ID=250µA 1.1 1000 Ciss 800 1 0.9 600 0.8 0.7 400 0.6 200 0.5 0 0 10 20 30 40 50 60 70 80 Coss Crss VDS(V) 0.4 -55 -30 -5 DocID025265 Rev 1 20 45 70 95 120 TJ(°C) 7/21 21 Electrical characteristics STD25N10F7, STF25N10F7, STP25N10F7 Figure 14. Normalized on-resistance vs temperature AM16014v1 RDS(on) Figure 15. Normalized BVDSS vs temperature AM16015v1 VDS (norm) (norm) ID=250µA ID=12.5A 2 1.04 1.5 1.02 1 1 0.5 0.98 0 -55 -30 -5 20 45 70 95 120 TJ(°C) 0.96 -55 -30 -5 Figure 16. Source-drain diode forward characteristics AM16016v1 VSD (V) 1.1 TJ=-50°C 1 TJ=25°C TJ=150°C 0.9 0.8 0.7 0.6 0 8/21 5 10 15 20 25 ISD(A) DocID025265 Rev 1 20 45 70 95 120 TJ(°C) STD25N10F7, STF25N10F7, STP25N10F7 3 Test circuits Test circuits Figure 17. Switching times test circuit for resistive load Figure 18. Gate charge test circuit VDD 12V 47kΩ 1kΩ 100nF 3.3 μF 2200 RL μF IG=CONST VDD VGS 100Ω Vi=20V=VGMAX VD RG 2200 μF D.U.T. D.U.T. VG 2.7kΩ PW 47kΩ 1kΩ PW AM01468v1 Figure 19. Test circuit for inductive load switching and diode recovery times A A AM01469v1 Figure 20. Unclamped inductive load test circuit L A D G D.U.T. FAST DIODE B B VD L=100μH S 3.3 μF B 25 Ω 1000 μF D VDD 2200 μF 3.3 μF VDD ID G RG S Vi D.U.T. Pw AM01470v1 AM01471v1 Figure 21. Unclamped inductive waveform Figure 22. Switching time waveform ton V(BR)DSS tdon VD toff tr tdoff tf 90% 90% IDM 10% ID VDD 10% 0 VDD VDS 90% VGS AM01472v1 0 DocID025265 Rev 1 10% AM01473v1 9/21 21 Package mechanical data 4 STD25N10F7, STF25N10F7, STP25N10F7 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 10/21 DocID025265 Rev 1 STD25N10F7, STF25N10F7, STP25N10F7 Package mechanical data Table 8. DPAK (TO-252) mechanical data mm Dim. Min. Typ. Max. A 2.20 2.40 A1 0.90 1.10 A2 0.03 0.23 b 0.64 0.90 b4 5.20 5.40 c 0.45 0.60 c2 0.48 0.60 D 6.00 6.20 D1 E 5.10 6.40 6.60 E1 4.70 e 2.28 e1 4.40 4.60 H 9.35 10.10 L 1.00 1.50 (L1) 2.80 L2 0.80 L4 0.60 1.00 R V2 0.20 0° 8° DocID025265 Rev 1 11/21 21 Package mechanical data STD25N10F7, STF25N10F7, STP25N10F7 Figure 23. DPAK (TO-252) drawings 0068772_K 12/21 DocID025265 Rev 1 STD25N10F7, STF25N10F7, STP25N10F7 Package mechanical data Figure 24. DPAK footprint (a) Footprint_REV_K a. All dimensions are in millimeters DocID025265 Rev 1 13/21 21 Package mechanical data STD25N10F7, STF25N10F7, STP25N10F7 Table 9. TO-220FP mechanical data mm Dim. Min. Max. A 4.4 4.6 B 2.5 2.7 D 2.5 2.75 E 0.45 0.7 F 0.75 1 F1 1.15 1.70 F2 1.15 1.70 G 4.95 5.2 G1 2.4 2.7 H 10 10.4 L2 14/21 Typ. 16 L3 28.6 30.6 L4 9.8 10.6 L5 2.9 3.6 L6 15.9 16.4 L7 9 9.3 Dia 3 3.2 DocID025265 Rev 1 STD25N10F7, STF25N10F7, STP25N10F7 Package mechanical data Figure 25. TO-220FP drawing 7012510_Rev_K_B DocID025265 Rev 1 15/21 21 Package mechanical data STD25N10F7, STF25N10F7, STP25N10F7 Table 10. TO-220 type A mechanical data mm Dim. Min. Typ. A 4.40 4.60 b 0.61 0.88 b1 1.14 1.70 c 0.48 0.70 D 15.25 15.75 D1 16/21 Max. 1.27 E 10 10.40 e 2.40 2.70 e1 4.95 5.15 F 1.23 1.32 H1 6.20 6.60 J1 2.40 2.72 L 13 14 L1 3.50 3.93 L20 16.40 L30 28.90 ∅P 3.75 3.85 Q 2.65 2.95 DocID025265 Rev 1 STD25N10F7, STF25N10F7, STP25N10F7 Package mechanical data Figure 26. TO-220 type A drawings 0015988_typeA_Rev_S DocID025265 Rev 1 17/21 21 Packaging mechanical data 5 STD25N10F7, STF25N10F7, STP25N10F7 Packaging mechanical data Table 11. DPAK (TO-252) tape and reel mechanical data Tape Reel mm mm Dim. Dim. Min. Max. A0 6.8 7 A B0 10.4 10.6 B 1.5 12.1 C 12.8 1.6 D 20.2 G 16.4 50 B1 18/21 Min. Max. 330 13.2 D 1.5 D1 1.5 E 1.65 1.85 N F 7.4 7.6 T K0 2.55 2.75 P0 3.9 4.1 Base qty. 2500 P1 7.9 8.1 Bulk qty. 2500 P2 1.9 2.1 R 40 T 0.25 0.35 W 15.7 16.3 DocID025265 Rev 1 18.4 22.4 STD25N10F7, STF25N10F7, STP25N10F7 Packaging mechanical data Figure 27. Tape for DPAK (TO-252) 10 pitches cumulative tolerance on tape +/- 0.2 mm T P0 Top cover tape P2 D E F B1 W K0 B0 For machine ref. only including draft and radii concentric around B0 A0 P1 D1 User direction of feed R Bending radius User direction of feed AM08852v1 Figure 28. Reel for DPAK (TO-252) T REEL DIMENSIONS 40mm min. Access hole At slot location B D C N A Full radius Tape slot in core for tape start 25 mm min. width G measured at hub AM08851v2 DocID025265 Rev 1 19/21 21 Revision history 6 STD25N10F7, STF25N10F7, STP25N10F7 Revision history Table 12. Document revision history 20/21 Date Revision 17-Sep-2013 1 Changes First release. DocID025265 Rev 1 STD25N10F7, STF25N10F7, STP25N10F7 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS. NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2013 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com DocID025265 Rev 1 21/21 21