STTH1002CFP

STTH1002C High efficiency ultrafast diode Datasheet - production data Features $  Suited for SMPS . $  Low losses  Low forward and reverse recovery times .  Insulated package: TO-220FPAB – Insulating voltage: 2000 VRMS sine $  High junction temperature $ . 72)3$% $ ,ð3$. . $  Low leakage current  ECOPACK®2 compliant component for DPAK and D²PAK on demand . Description $ . Dual center tap rectifier suited for switch mode power supplies and high frequency DC to DC converters. $ Packaged in DPAK, D²PAK, TO-220AB, I²PAK and TO-220FPAB, this device is intended for use in low voltage, high frequency inverters, free wheeling and polarity protection applications. 72$% . . Table 1. Device summary $ $ $ $ 'ð3$. . . $ $ $ '3$. September 2016 This is information on a product in full production. Symbol Value IF(AV) Up to 2 x 8 A VRRM 200 V Tj (max) 175 °C VF (typ) 0.78 V trr (typ) 20 ns $ DocID10182 Rev 8 1/17 www.st.com Characteristics 1 STTH1002C Characteristics Table 2. Absolute ratings (limiting values per diode at 25 °C, unless otherwise specified) Symbol VRRM Parameter Repetitive peak reverse voltage I2 IF(RMS) IF(AV) 2 PAK, D PAK,TO-220AB, TO-220FPAB Unit 200 V 20 Forward rms current A DPAK 10 Tc = 155 °C Per diode 5 Tc = 150 °C Per device I2PAK, DPAK, D2PAK,TO-220AB T = 135 °C Per diode c 10 Tc = 125 °C Per device 16 Tc = 140 °C Per diode 5 Tc = 120 °C Per device 10 Tc = 110 °C Per diode 8 Tc = 75 °C Per device 16 Average forward current  = 0.5, square wave TO-220FPAB IFSM Surge non repetitive forward current Tstg Storage temperature range Tj Value tp = 10 ms sinusoidal Maximum operating junction temperature 8 A 50 A -65 to +175 °C 175 °C Table 3. Thermal parameter Symbol Parameter I2PAK, DPAK, D2PAK,TO-220AB Rth(j-c) Max. value Per diode 4.0 Per device 2.5 Per diode 6.5 Per device 5.0 Junction to case TO-220FPAB Rth(c) °C/W I2PAK, DPAK, D2PAK,TO-220AB 1.0 TO-220FPAB 3.5 Coupling When the diodes 1 and 2 are used simultaneously:  Tj (diode1) = P(diode1) x Rth(j-c) (per diode) + P(diode2) x Rth(c) 2/17 Unit DocID10182 Rev 8 STTH1002C Characteristics Table 4. Static electrical characteristics (per diode) Symbol IR(1) Parameter Test conditions Reverse leakage current Tj = 25 °C Tj = 125 °C Tj = 25 °C VF(2) Forward voltage drop Tj = 150 °C Min. Typ. VR = VRRM Max. Unit 5 µA - 3 40 IF = 5 A - 1.10 IF = 10 A - 1.25 IF = 5 A - IF = 10 A - V 0.78 0.89 1.05 1. Pulse test: tp = 5 ms,  < 2% 2. Pulse test: tp = 380 µs,  < 2% To evaluate the conduction losses, use the following equation: P = 0.73 x IF(AV) + 0.032 x IF2(RMS) Table 5. Dynamic electrical characteristics (per diode) Symbol trr IRM tfr Parameter Test conditions Typ. Max. Unit Reverse recovery time Tj = 25 °C IF = 1 A VR = 30 V dIF/dt = 100 A/µs - 20 25 ns Reverse recovery current IF = 5 A VR = 160 V dIF/dt = 200 A/µs - 5.9 7.6 A IF = 5 A VFR = 1.1 x VFmax dIF/dt = 100 A/µs - 110 ns IF = 5 A dIF/dt = 100 A/µs - Tj = 125 °C Forward recovery time Tj = 25 °C VFP Min. Forward recovery voltage DocID10182 Rev 8 2.4 V 3/17 17 Characteristics STTH1002C Figure 1. Peak current versus duty cycle (per diode) Figure 2. Forward voltage drop versus forward current (typical values, per diode) ,0$  ,)$  7    3 : į WS7  WS  7  ƒ& M  3 :    7  ƒ& M      3 :        į      Figure 3. Forward voltage drop versus forward current (maximum values, per diode)  ,)$               9 9 ) Figure 4. Relative variation of thermal impedance junction to case versus pulse duration  =WKMF5WKMF 6LQJOHSXOVH 72$% ,ð3$. 'ð3$. '3$.      7  ƒ& M  7  ƒ&  M                  ( Figure 5. Relative variation of thermal impedance junction to case versus pulse duration  ( ( ( W3V 9 9 ) = 5  WKMF WKMF Figure 6. Junction capacitance versus reverse voltage applied (typical values, per diode) &S)  ) 0+] 9RVF P9506 7M ƒ& 6LQJOHSXOVH 72)3$%   ( 4/17 ( ( W3V ( (   DocID10182 Rev 8  9 9 5  STTH1002C Characteristics Figure 7. Reverse recovery charges versus dIF/dt (typical values, per diode)  4UU Q&   Figure 8. Reverse recovery time versus dIF/dt (typical values, per diode) WUUQV  ,  $ ) 95 9 ,  $ ) 95 9  7  ƒ& M    7  ƒ&    M  7  ƒ&  M     7  ƒ& M         GO GW$—V )    GO)GW$—V Figure 9. Peak reverse recovery current versus Figure 10. Dynamic parameters versus junction dIF/dt (typical values, per diode) temperature (reference: Tj = 125 °C) , $  50 ,  $  ) 95 9                , 50 7M ƒ&  4  7M ƒ& 55    GO)GW$—V  Figure 11. Thermal resistance junction to ambient versus copper surface under tab  ,) $ 95 9    5   7Mƒ&    Figure 12. Thermal resistance junction to ambient versus copper surface under tab 5WKMDƒ&:  (SR[\SULQWHGERDUG)5FRSSHUWKLFNQHVV —P 'ð3$.   WKMD ƒ&: (SR[\SULQWHGERDUG)5FRSSHUWKLFNQHVV —P '3$.                       6&XFPð      DocID10182 Rev 8     6&XFPð     5/17 17 Package information 2 STTH1002C Package information  Epoxy meets UL94, V0  Cooling method: by conduction (C)  Recommended torque value:0.55 N·m for TO-220AB and TO-220FPAB  Maximum torque value: 0.7 N·m for TO-220AB and TO-220FPAB In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 2.1 TO-220AB package information Figure 13. TO-220AB package outline $ ( ‡3 5HVLQJDWH PPPD[ SURWUXVLRQ ) 4 + ' ' / / E - / / E H 5HVLQJDWH PPPD[ SURWUXVLRQ H 5HVLQJDWHSRVLWLRQDFFHSWHGLQHDFKRIWKHWZR SRVLWLRQVKRZQDVZHOODVWKHV\PPHWULFDORSSRVLWHV 6/17 DocID10182 Rev 8 F STTH1002C Package information Table 6. TO-220AB package mechanical data Dimensions Ref. Millimeters Inches Min. Max. Min. Max. A 4.40 4.60 0.170 0.181 b 0.61 0.88 0.024 0.035 b1 1.14 1.70 0.045 0.067 c 0.48 0.70 0.019 0.027 D 15.25 15.75 0.600 0.620 D1 1.27 typ. 0.050 typ. E 10.00 10.40 0.393 0.41 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.194 0.202 F 1.23 1.32 0.048 0.052 H1 6.20 6.60 0.244 0.259 J1 2.40 2.72 0.094 0.107 L 13.00 14.00 0.511 0.551 L1 3.50 3.93 0.137 0.154 L20 16.40 typ. 0.645 typ. L30 28.90 typ. 1.137 typ. P 3.75 3.85 0.147 0.151 Q 2.65 2.95 0.104 0.116 DocID10182 Rev 8 7/17 17 Package information 2.2 STTH1002C TO-220FPAB package information Figure 14. TO-220FPAB package outline $ % + 'LD / / / / / ) / ) * ) * 8/17 ' DocID10182 Rev 8 ( STTH1002C Package information Table 7. TO-220FPAB package mechanical data Dimensions Ref. Millimeters Inches Min. Max. Min. Max. A 4.40 4.60 0.173 0.181 B 2.50 2.70 0.098 0.106 D 2.50 2.75 0.098 0.108 E 0.45 0.70 0.018 0.027 F 0.75 1.00 0.030 0.039 F1 1.15 1.70 0.045 0.067 F2 1.15 1.70 0.045 0.067 G 4.95 5.20 0.195 0.205 G1 2.40 2.70 0.094 0.106 H 10.00 10.40 0.393 0.409 L2 16.00 Typ. 0.630 Typ. L3 28.60 30.60 1.126 1.205 L4 9.80 10.60 0.386 0.417 L5 2.90 3.60 0.114 0.142 L6 15.90 16.40 0.626 0.646 L7 9.00 9.30 0.354 0.366 Dia. 3.00 3.20 0.118 0.126 DocID10182 Rev 8 9/17 17 Package information 2.3 STTH1002C D²PAK package information Figure 15. D2PAK package outline $ ( F / ' + / - E E H F H ( ( ' $ ' / 5  *DXJHSODQH 9 Note: 10/17 This package drawing may slightly differ from the physical package. However, all the specified dimensions are guaranteed. DocID10182 Rev 8 STTH1002C Package information Table 8. D2PAK package mechanical data Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. 0.171 Typ. Max. A 4.36 4.60 A1 0 0.25 b 0.70 0.93 0.027 0.037 b2 1.14 1.70 0.045 0.067 c 0.38 0.69 0.014 0.027 c2 1.19 1.36 0.046 0.053 D 8.60 9.35 0.338 0.368 D1 6.90 8.00 0.271 0.315 D2 1.10 1.50 0.043 0.060 E 10.00 10.55 0.393 0.415 E1 8.10 8.90 0.318 0.350 E2 6.85 7.25 0.269 0.285 e 0.181 0.010 2.54 0.100 e1 4.88 5.28 0.192 0.208 H 15.00 15.85 0.590 0.624 J1 2.49 2.90 0.098 0.114 L 1.90 2.79 0.074 0.110 L1 1.27 1.65 0.050 0.065 L2 1.30 1.78 0.051 0.070 R V2 0.40 0.016 0° 8° 0° 8° Figure 16. Footprint (dimensions in mm)        DocID10182 Rev 8 11/17 17 Package information 2.4 STTH1002C DPAK package information Figure 17. DPAK package outline ( $ E 7KHUPDOSDG ( / F ' ' + 5 / $ E H H 5 F $ / / 9  Note: 12/17 *DXJH SODQH This package drawing may slightly differ from the physical package. However, all the specified dimensions are guaranteed. DocID10182 Rev 8 STTH1002C Package information Table 9. DPAK package mechanical data Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A 2.18 2.40 0.085 0.094 A1 0.90 1.10 0.035 0.043 A2 0.03 0.23 0.001 0.009 b 0.64 0.90 0.025 0.035 b4 4.95 5.46 0.194 0.214 c 0.46 0.61 0.018 0.024 c2 0.46 0.60 0.018 0.023 D 5.97 6.22 0.235 0.244 D1 4.95 5.60 0.194 0.220 E 6.35 6.73 0.250 0.264 E1 4.32 5.50 0.170 0.216 e 2.28 0.090 e1 4.40 4.70 0.173 0.185 H 9.35 10.40 0.368 0.409 L 1.00 1.78 0.039 0.070 L2 1.27 0.050 L4 0.60 1.02 0.023 0.040 V2 -8° +8° -8° 8° Figure 18. DPAK footprint dimensions (in mm)      % 7KHGHYLFHPXVWEHSRVLWLRQHGZLWKLQ DocID10182 Rev 8 $   $ % 13/17 17 Package information 2.5 STTH1002C I²PAK package information Figure 19. I2PAK package outline $ ( F / ' / $ E / E H H 14/17 DocID10182 Rev 8 F STTH1002C Package information Table 10. I2PAK package mechanical data Dimensions Ref. Millimeters Inches Min. Max. Min. Max. A 4.40 4.60 0.173 0.181 A1 2.40 2.72 0.094 0.107 b 0.61 0.88 0.024 0.035 b1 1.14 1.70 0.044 0.067 c 0.49 0.70 0.019 0.028 c2 1.23 1.32 0.048 0.052 D 8.95 9.35 0.352 0.368 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.195 0.203 E 10.00 10.40 0.394 0.409 L 13.00 14.00 0.512 0.551 L1 3.50 3.93 0.138 0.155 L2 1.27 1.40 0.050 0.055 DocID10182 Rev 8 15/17 17 Ordering information 3 STTH1002C Ordering information Table 11. Ordering information 4 Order code Marking Package Weight Base qty Delivery mode STTH1002CB STTH1 002CB DPAK 0.32 g 75 Tube STTH1002CB-TR STTH1 002CB DPAK 0.32 g 2500 Tape and reel STTH1002CT STTH1002CT TO-220AB 1.9 g 50 Tube STTH1002CG-TR STTH1002CG D2PAK 1.38 g 1000 Tape and reel STTH1002CR STTH1002CR I2 1.5 g 50 Tube STTH1002CFP STTH1002CFP 1.9 g 50 Tube PAK TO-220FPAB Revision history Table 12. Document revision history 16/17 Date Revision Changes Mar-2004 4 Last issue. 22-Mar-2013 5 Updated Table 7. 05-Jan-2015 6 Updated DPAK and D²PAK package information. 24-Apr-2015 7 Updated Figure 15. 20-Sep-2016 8 Updated DPAK package information and reformatted to current standard. DocID10182 Rev 8 STTH1002C IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved DocID10182 Rev 8 17/17 17