VND5E012MYTR-E

VND5E012MY-E Double channel high-side driver with analog current sense for automotive applications Datasheet - production data – Load current limitation – Self limiting of fast thermal transients – Protection against loss of ground and loss of VCC – Overtemperature shutdown with auto restart (thermal shutdown) – Reverse battery protection with self switch on of the Power MOSFET – Electrostatic discharge protection PowerSSO-36 Features Max transient supply voltage VCC 41V Operating voltage range VCC 4.5 to 28V Max on-state resistance (per ch.) RON 12 mΩ Current limitation (typ) ILIMH 74 A Off-state supply current IS 2 µA(1) Applications • All types of resistive, inductive and capacitive loads • Suitable as LED driver 1. Typical value with all loads connected. Description • General – Inrush current active management by power limitation – Very low standby current – 3.0V CMOS compatible inputs – Optimized electromagnetic emissions – Very low electromagnetic susceptibility – In compliance with the 2002/95/EC european directive – Very low current sense leakage The VND5E012MY-E is a double channel highside driver manufactured in the STMicroelectronics® VIPower® M0-5 technology and housed in the tiny PowerSSO-36 package. The VND5E012MY-E is designed to drive 12 V automotive grounded loads delivering protection, diagnostics and easy 3 V and 5 V CMOS compatible interface with any microcontroller. • Diagnostic functions – Proportional load current sense – High current sense precision for wide current range – Current sense disable – Overload and short to ground (power limitation) indication – Thermal shutdown indication • Protections – Undervoltage shutdown – Overvoltage clamp October 2013 This is information on a product in full production. The device integrates advanced protective functions such as load current limitation, inrush and overload active management by power limitation, overtemperature shut-off with auto restart and over-voltage active clamp. A dedicated analog current sense pin is associated with every output channel in order to provide Enhanced diagnostic functions including fast detection of overload and short-circuit to ground through power limitation indication and overtemperature indication. The current sensing and diagnostic feedback of the whole device can be disabled by pulling the CS_DIS pin high to allow sharing of the external sense resistor with other similar devices. DocID16503 Rev 5 1/36 www.st.com Contents VND5E012MY-E Contents 1 Block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3 4 2.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.4 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 2.5 Electrical characteristics curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.1 Load dump protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.2 MCU I/Os protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.3 Current sense and diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 3.4 Maximum demagnetization energy (VCC = 13.5V) . . . . . . . . . . . . . . . . . 25 Package and PCB thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.1 5 PowerSSO-36 thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 5.1 ECOPACK® package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 5.2 PowerSSO-36 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 5.3 Packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 6 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 2/36 DocID16503 Rev 5 VND5E012MY-E List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Pin function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Suggested connections for unused and not connected pins . . . . . . . . . . . . . . . . . . . . . . . . 6 Absolute maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Switching (VCC = 13V; Tj = 25°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Logic inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Protections and diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Current sense (8V @    $    %           ,RXW>$@ 0 D[ 7M ƒ&W WRƒ&   %  0LQ 7M  ƒ&W WR ƒ& $0 *$3*5, Note: Parameter guaranteed by design; it is not tested. DocID16503 Rev 5 15/36 35 Electrical specifications VND5E012MY-E Table 10. Truth table Input Output Sense (VCSD=0V)(1) Normal operation L H L H 0 Nominal Overtemperature L H L L 0 VSENSEH Undervoltage L H L L 0 0 H X (no power limitation) Cycling (power limitation) Nominal Conditions Overload H VSENSEH Short circuit to GND (Power limitation) L H L L 0 VSENSEH Negative output voltage clamp L L 0 1. If the VCSD is high, the SENSE output is at a high impedance, its potential depends on leakage currents and external circuit. 16/36 DocID16503 Rev 5 VND5E012MY-E Electrical specifications Table 11. Electrical transient requirements (part 1) ISO 7637-2: 2004(E) Test levels(1) Number of pulses or test times Burst cycle/pulse repetition time Delays and impedance Test pulse III IV 1 -75 V -100 V 5000 pulses 0.5 s 5s 2 ms, 10 Ω 2a +37 V +50 V 5000 pulses 0.2 s 5s 50 µs, 2 Ω 3a -100 V -150 V 1h 90 ms 100 ms 0.1 µs, 50 Ω 3b +75 V +100 V 1h 90 ms 100 ms 0.1 µs, 50 Ω 4 -6 V -7 V 1 pulse 100 ms, 0.01 Ω 5b(2) +65 V +87 V 1 pulse 400 ms, 2 Ω 1. The above test levels must be considered referred to VCC = 13.5 V except for pulse 5b. 2. Valid in case of external load dump clamp: 40V maximum referred to ground. The protection strategy allows PowerMOS to be cyclically switched on during load dump, so distributing the load dump energy along the time and to transfer a part of it to the load. Table 12. Electrical transient requirements (part 2) Test level results(1) ISO 7637-2: 2004(E) Test pulse III IV 1 C C 2a C C 3a C C 3b C C 4 C C 5b(2)(3) C C 1. The above test levels must be considered referred to VCC = 13.5 V except for pulse 5b 2. Valid in case of external load dump clamp: 40V maximum referred to ground. The protection strategy allows PowerMOS to be cyclically switched on during load dump, so distributing the load dump energy along the time and to transfer a part of it to the load. 3. Suppressed load dump (pulse 5b) is withstood with a minimum load connected as specified in Table 3: Absolute maximum rating. Table 13. Electrical transient requirements (part 3) Class Contents C All functions of the device are performed as designed after exposure to disturbance. E One or more functions of the device are not performed as designed after exposure to disturbance and cannot be returned to proper operation without replacing the device. DocID16503 Rev 5 17/36 35 Electrical specifications 2.4 VND5E012MY-E Waveforms Figure 10. Normal operation 1RUPDORSHUDWLRQ ,1387 1RPLQDOORDG 1RPLQDOORDG ,287 96(16( 9&6B',6 $*9 Figure 11. Overload or short to GND 2YHUORDGRU6KRUWWR*1' ,1387 3RZHU/LPLWDWLRQ , /LP+! 7KHUPDOF\FOLQJ , /LP/! ,287 96(16( 9&6B',6 $*9 18/36 DocID16503 Rev 5 VND5E012MY-E Electrical specifications Figure 12. Intermittent overload ,QWHUPLWWHQW2YHUORDG ,1387 2YHUORDG ,/LP+ ! 1RPLQDOORDG ,/LP/ ! ,287 96(16(+ ! 96(16( 9&6B',6 $*9 Figure 13. TJ evolution in overload or short to GND ,1387 6HOIOLPLWDWLRQRIIDVWWKHUPDOWUDQVLHQWV 776' 7+