VND5E050JTR-E

VND5E050J-E VND5E050K-E Double channel high side driver for automotive applications Features Max supply voltage Operating voltage range Max On-State resistance (per ch.) Current limitation (typ) Off state supply current (1) Typical value with all loads connected. ■ VCC VCC RON ILIMH IS 41V 4.5 to 28V 50 mΩ 27 A 2 µA(1) PowerSSO-12 PowerSSO-24 General – Inrush current active management by power limitation – Very low stand-by current – 3.0V CMOS compatible inputs – Optimized electromagnetic emissions – Very low electromagnetic susceptibility – In compliance with the 2002/95/EC european directive Diagnostic functions – Open Drain status output – On-state open load detection – Off-state open load detection – Output short to Vcc detection – Overload and short to ground (power limitation) indication – Thermal shutdown indication Protections – Undervoltage shutdown – Overvoltage clamp – Load current limitation – Self limiting of fast thermal transients – Protection against loss of ground and loss of VCC – Over-temperature shutdown with autorestart (thermal shutdown) – Reverse battery protected(a) – Electrostatic discharge protection Application ■ All types of resistive, inductive and capacitive loads Description The VND5E050J-E and VND5E050K-E are double channel high-side drivers manufactured in the ST proprietary VIPower M0-5 technology and housed in the tiny PowerSSO-12 and PowerSSO-24 packages. The VND5E050J-E and VND5E050K-E are designed to drive automotive grounded loads delivering protection, diagnostics and easy 3V and 5V CMOS-compatible interface with any microcontroller. The devices integrate advanced protective functions such as load current limitation, inrush and overload active management by power limitation, over-temperature shut-off with auto-restart and over-voltage active clamp. A dedicated active low digital status pin is associated with every output channel in order to provide Enhanced diagnostic functions including fast detection of overload and short-circuit to ground, over-temperature indication, short-circuit to VCC diagnosis and ON & OFF state open-load detection. The diagnostic feedback of the whole device can be disabled by pulling the STAT_DIS pin up, thus allowing wired-ORing with other similar devices. ■ ■ (a )See Application schematic on page 22. February 2008 Rev 1 1/40 www.st.com 40 Contents VND5E050J-E / VND5E050K-E Contents 1 2 Block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.1 2.2 2.3 2.4 2.5 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Electrical characteristics curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 3.1 GND protection network against reverse battery . . . . . . . . . . . . . . . . . . . 22 3.1.1 3.1.2 Solution 1: resistor in the ground line (RGND only) . . . . . . . . . . . . . . . . 22 Solution 2: diode (DGND) in the ground line . . . . . . . . . . . . . . . . . . . . . 23 3.2 3.3 3.4 3.5 Load dump protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 MCU I/Os protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Open load detection in Off state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Maximum demagnetization energy (VCC = 13.5V) . . . . . . . . . . . . . . . . . 25 4 Package and PCB thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.1 4.2 PowerSSO-12 thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 PowerSSO-24 thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 5 Package and packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 5.1 5.2 5.3 5.4 5.5 ECOPACK® packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 PowerSSO-12 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 PowerSSO-24 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 PowerSSO-12 packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 PowerSSO-24 packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 6 7 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 2/40 VND5E050J-E / VND5E050K-E List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 18. Pin function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Suggested connections for unused and not connected pins . . . . . . . . . . . . . . . . . . . . . . . . 6 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Switching (VCC = 13V; Tj = 25°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Status pin (VSD=0V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Protections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Openload detection (8V VOL VOL IOUT > IOL VOUT > VOL VOUT IOUT IOL IOUT < IOL tDSTK(on) VSTATUS tDOL(on) VST_DIS Figure 14. TJ evolution in Overload or Short to GND TJ evolution in Overload or Short to GND INPUT Self-limitation of fast thermal transients TTSD TR THYST TJ_START TJ ILimH > Power Limitation < ILimL IOUT 18/40 VND5E050J-E / VND5E050K-E Electrical specifications 2.5 Electrical characteristics curves Figure 16. High level input current Iih (µA) 5 4,5 600 Figure 15. Off state output current Iloff (nA) 700 500 Off State Vcc=13V Vin=Vout=0V Vin=2.1V 4 3,5 3 2,5 400 300 2 1,5 1 200 100 0,5 0 -50 -25 0 25 50 75 100 125 150 175 0 -50 -25 0 25 50 75 100 125 150 175 Tc (°C) Tc (°C) Figure 17. Input clamp voltage Vicl (V) 7 6,8 Figure 18. Input high level Vih (V) 4 3,5 3 lin=1mA 6,6 6,4 6,2 6 5,8 5,6 2,5 2 1,5 1 5,4 5,2 5 -50 -25 0 25 50 75 100 125 150 175 0,5 0 -50 -25 0 25 50 75 100 125 150 175 Tc (°C) Tc (°C) Figure 19. Input low level Vil (V) 2 1,8 1,6 1,4 1,2 1 0,8 0,6 0,4 0,2 0 -50 -25 0 25 50 75 100 125 150 175 Figure 20. Low level STAT_DIS current Isdl (µA) 5 4,5 Vsd= 0.9V 4 3,5 3 2,5 2 1,5 1 0,5 0 -50 -25 0 25 50 75 100 125 150 175 Tc (°C) Tc (°C) 19/40 Electrical specifications VND5E050J-E / VND5E050K-E Figure 21. On state resistance vs Tcase Ron (mOhm) 300 Figure 22. High level STAT_DIS current Isdh (µA) 5 4,5 250 Iout= 2A Vcc=13V Vsd= 2.1V 4 3,5 3 200 150 2,5 2 100 1,5 1 0,5 50 0 -50 -25 0 25 50 75 100 125 150 175 0 -50 -25 0 25 50 75 100 125 150 175 Tc (°C) Tc (°C) Figure 23. On state resistance vs VCC Ron (mOhm) 100 Figure 24. Low level input current Iil (µA) 5 4,5 Tc=150°C 80 4 3,5 Vin=0.9V Tc=125°C 60 3 Tc=25°C 40 2,5 2 1,5 Tc=-40°C 20 1 0,5 0 0 5 10 15 20 25 30 35 40 0 -50 -25 0 25 50 75 100 125 150 175 Tc (°C) Tc (°C) Figure 25. ILIM vs Tcase Ilimh (A) 40 Figure 26. Turn-On voltage slope (dVout/dt )On (V/ms) 1000 900 35 Vcc=13V 800 700 600 Vcc=13V RI=6.5 Ohm 30 25 500 400 20 300 200 100 15 10 -50 -25 0 25 50 75 100 125 150 0 -50 -25 0 25 50 75 100 125 150 175 Tc (°C) Tc (°C) 20/40 VND5E050J-E / VND5E050K-E Electrical specifications Figure 27. Undervoltage shutdown Vusd (V) 8 7 Figure 28. Turn-Off voltage slope (dVout/dt )Off (V/ms) 600 550 500 6 5 450 400 350 Vcc=13V RI= 6.5 Ohm 4 3 300 250 200 2 1 150 100 50 0 -50 -25 0 25 50 75 100 125 150 175 0 -50 -25 0 25 50 75 100 125 150 175 Tc (°C) Tc (°C) Figure 29. STAT_DIS clamp voltage Vsdcl(V) 10 9 8 7 6 5 4 3 Figure 30. High level STAT_DIS voltage VsdH(V) 4 3,5 Isd = 1 mA 3 2,5 2 1,5 1 2 1 0 -50 -25 0 25 50 75 100 125 150 175 0,5 0 -50 -25 0 25 50 75 100 125 150 175 Tc (°C) Tc (°C) Figure 31. Low level STAT_DIS voltage VsdL(V) 3 2,5 2 1,5 1 0,5 0 -50 -25 0 25 50 75 100 125 150 175 Tc (°C) 21/40 Application information VND5E050J-E / VND5E050K-E 3 Application information Figure 32. Application schematic +5V +5V VCC Rprot STAT_DIS Dld Rprot µC OUTPUT Rprot STATUS GND INPUT VGND RGND DGND Note: Channel 2 has the same internal circuit as channel 1. 3.1 3.1.1 GND protection network against reverse battery Solution 1: resistor in the ground line (RGND only) This can be used with any type of load. The following is an indication on how to dimension the RGND resistor. 1. 2. RGND ≤600mV / (IS(on)max). RGND ≥ (− CC) / (-IGND) V where -IGND is the DC reverse ground pin current and can be found in the absolute maximum rating section of the device datasheet. Power Dissipation in RGND (when VCC