SI9105DN02-E3

End of Life. Last Available Purchase Date is 31-Dec-2014 Si9105 Vishay Siliconix 1-W High-Voltage Switchmode Regulator FEATURES CCITT Compatible Current-Mode Control Low Power Consumption (less than 5 mW) 10- to 120-V Input Range 200-V, 250-mA MOSFET Internal Start-Up Circuit Current-Mode Control SHUTDOWN and RESET DESCRIPTION The Si9105 high-voltage switchmode regulator is a monolithic BiC/DMOS integrated circuit which contains most of the components necessary to implement a high-efficiency dc/dc converter in ISDN terminals up to 3 watts. A 0.5-mA max supply current makes possible the design of a dc/dc converter with 60% efficiency at 25 mW, therefore meeting the recommended performance under the CCITT I.430 specifications. This device may be used with an appropriate transformer to implement isolated flyback power converter topologies to provide single or multiple regulated dc outputs (i.e., 5 V). The Si9105 is available in both standard and lead (Pb)-free 16-pin wide-body SOIC, 14-pin plastic DIP and 20-pin PLCC packages which are specified to operate over the industrial temperature range of −40 C to 85 C. FUNCTIONAL BLOCK DIAGRAM FB COMP DISCHARGE OSC IN Error Amplifier OSC OUT OSC − + VREF 2V − 4 V (1%) Current-Mode Comparator + Ref Gen Clock (½ fOSC) R Q S + − DRAIN C/L Comparator −VIN (BODY) 1.2 V BIAS Current Sources To Internal Circuits VCC VCC +VIN − 8.7 V + Undervoltage Comparator SOURCE S SHUTDOWN R RESET Q − + Document Number: 70003 S-42030—Rev. H, 15-Nov-04 9.3 V www.vishay.com 1 Si9105 Vishay Siliconix ABSOLUTE MAXIMUM RATINGS Voltages Referenced to −VIN (VCC < +VIN + 0.3 V) VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 V +VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 V VDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 V ID (Peak) (300
s pulse, 2% duty cycle) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 A ID (rms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 mA Logic Inputs (RESET, SHUTDOWN, OSC IN) . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VCC + 0.3 V Power Dissipation (Package)a 14-Pin Plastic DIP (J Suffix)b . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 750 mW 16-Pin Plastic Wide-Body SOIC (W Suffix)c . . . . . . . . . . . . . . . . . . . 900 mW 20-Pin PLCC (N Suffix)d . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1400 mW Thermal Impedance (JA) 14-Pin Plastic DIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167_C/W 16-Pin Plastic Wide-Body SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140_C/W 20-Pin PLCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90_C/W Linear Inputs (FEEDBACK, SOURCE) . . . . . . . . . . . . . . . . . . . −0.3 V to 7 V HV Pre-Regulator Input Current (continuous) . . . . . . . . . . . . . . . . . . . . . 5 mA Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65 to 125_C Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40 to 85_C Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150_C Notes a. Device mounted with all leads soldered or welded to PC board. b. Derate 6 mW/_C above 25_C c. Derate 7.2 mW/_C above 25_C d. Derate 11.2 mW/_C above 25_C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. RECOMMENDED OPERATING RANGE Voltages Referenced to −VIN VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 V to 13.5 V ROSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 k to 1 M +VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 V to 120 V Linear Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to VCC − 3 V fOSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 kHz to 1 MHz Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to VCC SPECIFICATIONSa Test Conditions Unless Otherwise Specified Parameter Symbol DISCHARGE = −VIN = 0 V VCC = 10 V, +VIN = 48 V RBIAS = 820 k , ROSC = 910 k Limits Tempb Minc Typd Maxc Unit OSC IN = VIN (OSC Disabled) RL = 10 M Room 3.92 4.00 4.08 V k Reference Output Voltage VR Output Impedancee ZOUT OSC IN = −VIN Room 15 300 45 Short Circuit Current ISREF OSC IN = − VIN, VREF = −VIN Room 70 100 130
A Temperature Stabilitye TREF OSC IN = −VIN Full 0.25 1.0 mV/_C t = 1000 hrs, TA = 125_C Room 5.00 25.00 mV Long Term Stabilitye Oscillator Maximum Frequencye fMAX ROSC = 0 Room 1 3 Initial Accuracy fOSC See Note e Room 32 40 48 kHz Voltage Stability f/f f/f = f (13.5 V) − f (9.5 V)/f (9.5 V) Room 10 15 % Full 200 500 ppm/_C 4 4.04 V 25 500 nA "40 mV Temperature Coefficiente TOSC MHz Error Amplifier Feedback Input Voltage Input BIAS Current VFB FB Tied to COMP OSC IN = −VIN (OSC Disabled) Room IFB OSC IN = −VIN, VFB = 4 V Room Open Loop Voltage Gaine AVOL OSC IN = −VIN (OSC Disabled) Room Input Offset Voltage VOS Unity Gain Bandwidthe BW Dynamic Output Impedance ZOUT Output Current IOUT Power Supply Rejection www.vishay.com 2 PSRR 3.96 60 Room OSC IN = −VIN Room "15 0.5 Room Source (VFB = 3.4 V) Room Sink (VFB = 4.5 V) Room 10 V v VCC v 13.5 V Room 80 0.8 MHz 1 k −1.2 0.05 dB 0.08 70 −0.32 mA dB Document Number: 70003 S-42030—Rev. H, 15-Nov-04 Si9105 Vishay Siliconix SPECIFICATIONSa Test Conditions Unless Otherwise Specified Parameter Symbol DISCHARGE = −VIN = 0 V VCC = 10 V, +VIN = 48 V RBIAS = 820 k , ROSC = 910 k Limits Tempb Minc Typd Maxc Unit 0.8 1.0 1.2 V 200 300 ns 10
A Current Limit Threshold Voltage Delay to Outpute VSOURCE RL = 100  from DRAIN to VCC VFB = 0 V Room td RL = 100  from DRAIN to VCC VSOURCE = 1.5 V, See Figure 1 Room Input Voltage +VIN IIN = 10
A Room Input Leakage Current +IIN VCC w 10 V Room 120 V Pre-Regulator Start-Up Current ISTART Pulse Width v 300
s, VCC = 7 V Room 8 15 VCC Pre-Regulator Turn-Off Threshold Voltage VREG IPRE-REGULATOR = 10
A Room 7.5 9.3 9.7 Undervoltage Lockout VUVLO RL = 100  from DRAIN to VCC See Detailed Description Room 7.0 8.7 9.2 V VREG − VUVLO VDELTA Room 0.25 0.5 ICC Room 0.35 0.5 mA IBIAS Room 7.5 Room 50 mA Supply Supply Current Bias Current SHUTDOWN Delay tSD VSOURCE = −VIN, See Figure 2 SHUTDOWN Pulse Width tSW Room 50 RESET Pulse Width tRW Room 50 Latching Pulse Width SHUTDOWN and RESET Low tLW Room 25 Input Low Voltage VIL Room Input High Voltage VIH Room Input Current, Input Voltage High IIH VIN = 10 V Room Input Current. Input Voltage Low IIL VIN = 0 V Room −35 −25 200 220 See Figure 3
A 100 ns 2.0 8.0 1 5 V
A MOSFET Switch Breakdown Voltage V(BR)DSS IDRAIN = 100
A Full rDS(on) IDRAIN = 100 mA Room Drain Off Leakage Current IDSS VDRAIN = 100 V Room Drain Capacitance CDS Drain-Source On Resistanceg Room 5 35 V 7  10
A pF Notes a. Refer to PROCESS OPTION FLOWCHART for additional information. b. Room = 25_C, Cold and Hot = as determined by the operating temperature suffix. c. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. d. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. e. Guaranteed by design, not subject to production test. f. CSTRAY Pin 8 = v 5 pF g. Temperature coefficient of rDS(on) is 0.75% per _C, typical. Document Number: 70003 S-42030—Rev. H, 15-Nov-04 www.vishay.com 3 Si9105 Vishay Siliconix TIMING WAVEFORMS 1.5 V − SOURCE 0 VCC − VCC SHUTDOWN 0 tr v 10 ns 50% td VCC DRAIN 0 − − tSD DRAIN 0 10% 10% FIGURE 1. FIGURE 2. tSW VCC SHUTDOWN 0 tf v 10 ns 50% 50% 50% − tf, tf v 10 ns tLW VCC RESET 0 50% 50% 50% − tRW FIGURE 3. TYPICAL CHARACTERISTICS Output Switching Frequency vs. Oscillator Resistance f OUT (Hz) 1M 100 k 10 k 10 k 100 k 1M rOSC − Oscillator Resistance () FIGURE 4. www.vishay.com 4 Document Number: 70003 S-42030—Rev. H, 15-Nov-04 Si9105 Vishay Siliconix PIN CONFIGURATIONS PLCC-20 SO-16 (Wide-Body) PDIP-14 3 1 14 2 13 2 1 20 19 1 16 2 15 4 18 14 3 12 3 5 17 4 11 4 13 6 16 5 10 5 12 7 15 6 9 6 11 8 14 7 8 7 10 8 9 Top View 9 Top View 10 11 12 13 Top View PIN DESCRIPTION Pin Number Function 14-Pin Plastic DIP 16-Pin SOIC 20-Pin PLCC SOURCE 4 1 7 −VIN 5 2 8 VCC 6 4 9 OSCOUT 7 5 10 OSCIN 8 6 11 DISCHARGE 9 7 12 VREF 10 8 14 SHUTDOWN 11 9 16 RESET 12 10 17 COMP 13 11 18 FB 14 12 20 BIAS 1 13 2 +VIN 2 14 3 DRAIN 3 16 5 3, 15 1, 4, 6, 13, 15, 19 NC ORDERING INFORMATION Standard Part Number Si9105DJ02 Lead (Pb)-Free Part Number Si9105DJ02—E3 Package Temperature Range PDIP-14 Si9105DW Si9105DW-T1 (With Tape and Reel) Si9105DW-T1—E3 (With Tape and Reel) Si9105DN02 Si9105DN02—E3 Document Number: 70003 S-42030—Rev. H, 15-Nov-04 SOIC-16 (WB) −40 to 85 _C PLCC-20 www.vishay.com 5 Si9105 Vishay Siliconix DETAILED DESCRIPTION Pre-Regulator/Start-Up Section Due to the low quiescent current requirement of the Si9105 control circuitry, bias power can be supplied from the unregulated input power source, from an external regulated low-voltage supply, or from an auxiliary “bootstrap” winding on the output inductor or transformer. When power is first applied during start-up, +VIN will draw a constant current. The magnitude of this current is determined by a high-voltage depletion MOSFET device which is connected between +VIN and VCC. This start-up circuitry provides initial power to the IC by charging an external bypass capacitance connected to the VCC pin. The constant current is disabled when VCC exceeds 9.3 V. If VCC is not forced to exceed the 9.3-V threshold, then VCC will be regulated to a nominal value of 9.3 V by the pre-regulator circuit. As the supply voltage rises toward the normal operating conditions, an internal undervoltage (UV) lockout circuit keeps the output MOSFET disabled until VCC exceeds the undervoltage lockout threshold (typically 8.7 V). This guarantees that the control logic will be functioning properly and that sufficient gate drive voltage is available before the MOSFET turns on. The design of the IC is such that the undervoltage lockout threshold will not exceed the pre-regulator turn-off voltage. Power dissipation can be minimized by providing an external power source to VCC such that the constant current source is always disabled. BIAS To properly set the bias for the Si9105, a 820-k resistor should be tied from BIAS to −VIN. This determines the magnitude of bias current in all of the analog sections and the pull-up current for the SHUTDOWN and RESET pins. The current flowing in the bias resistor is nominally 7.5
A. Reference Section The reference section of the Si9105 consists of a temperature compensated buried zener and trimmable divider network. www.vishay.com 6 The output of the reference section is connected internally to the non-inverting input of the error amplifier. Nominal reference output voltage is 4 V. The trimming procedure that is used on the Si9105 brings the output of the error amplifier (which is configured for unity gain during trimming) to within "1% of 4 V. This automatically compensates for the input offset voltage in the error amplifier. The output impedance of the reference section has been purposely made high so that a low impedance external voltage source can be used to override the internal voltage source, if desired, without otherwise altering the performance of the device. Error Amplifier Closed-loop regulation is provided by the error amplifier, whose 1-k dynamic output impedance enables it to be used with feedback compensation (unlike transconductance amplifiers). A MOS differential input stage provides for low input current. The noninverting input to the error amplifier (VREF) is internally connected to the output of the reference supply and should be bypassed with a small capacitor to ground. Oscillator Section The oscillator consists of a ring of CMOS inverters, capacitors, and a capacitor discharge switch. Frequency is set by an external resistor between the OSC IN and OSC OUT pins. (See Typical Characteristics graph of resistor value vs. frequency.) The DISCHARGE pin should be tied to −VIN for normal internal oscillator operation. A frequency divider in the logic section limits switch duty cycle to a maximum of 50% by locking the switching frequency to one half of the oscillator frequency. Remote synchronization can be accomplished by capacitive coupling of a synchronization pulse into the OSC IN terminal. For a 5-V pulse amplitude and 0.5-
s pulse width, typical values would be 100 pF in series with 3 k to OSC IN. Document Number: 70003 S-42030—Rev. H, 15-Nov-04 Si9105 Vishay Siliconix DETAILED DESCRIPTION (CONT’D) Output Switch SHUTDOWN and RESET SHUTDOWN and RESET are intended for overriding the output MOSFET switch via external control logic. The two inputs are fed through a latch preceding the output switch. Depending on the logic state of RESET, SHUTDOWN can be either a latched or unlatched input. The output is off whenever SHUTDOWN is low. By simultaneously having SHUTDOWN and RESET low, the latch is set and SHUTDOWN has no effect until RESET goes high. The truth table for these inputs is given in Table 1. The output switch is a 7- , 200-V lateral DMOS transistor. Like discrete MOSFETs, the switch contains an intrinsic body-drain diode. However, the body contact in the Si9105 is connected internally to −VIN and is independent of the SOURCE. Table 1: Truth Table for the SHUTDOWN and RESET Pins SHUTDOWN RESET Output H H Normal Operation H Both pins have internal current source pull-ups and can be left disconnected when not in use. An added feature of the current sources is the ability to connect a capacitor and an open-collector driver to the SHUTDOWN pin to provide variable shutdown time. Normal Operation (No Change) L H Off (Not Latched) L L Off (Latched) L Off (Latched, No Change) APPLICATIONS 1N5819 +VIN 7 NC 0.1
F Lp = 3.8 m H 2 11 8 3 7 6 − 0.1
F Si9105DJ NC 0.1
F 12 14 10 13 1 4 0.1
F 5 71.5 k 1% 15 k 9 820 k 3.9  47.5 k 1% 4 −5 V 1N5819 12 V 9 47
F 150 k 0.22
F 0.1
F OUTPUT 3 1N4148 10 910 k + 220
F 5.6 V 8 20
F +5 V 2 1
F INPUT GND (GND Plane) FIGURE 5. CCITT Compatible ISDN Terminal Power Supply Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see http://www.vishay.com/ppg?70003. Document Number: 70003 S-42030—Rev. H, 15-Nov-04 www.vishay.com 7 Package Information Vishay Siliconix SOIC (WIDE-BODY): 16-LEAD (POWER IC ONLY) ECN: S-40079—Rev. A, 02-Feb-04 DWG: 5910 Ğ0.06$0.002D CAVITY NO. 0.2025$0.001 0.334$0.005 R0.004 16 15 14 13 12 11 10 0.010 9 R0.008 0.1475$0.001 R0.009 0.295$0.001 0.070$0.005 R0.004 1 2 3 4 5 6 7 4°$2° 8 0.032$0.005 DETAIL A 0.055$0.005 PIN 1 INDICATOR Ğ0.0470.007$0.001 dp SURFACE POLISHED 0.334$0.005 0.291$0.001 0.02045° 7°(4) 0.405$0.001 0.091$0.001 0.098$0.002 R0.004 0.295$0.001 0.406$0.004 0.041$0.001 0.050 TYP. 0.006$0.002 0.017$0.0003 DETAIL A All Dimensions In Inches Document Number: 72805 28-Jan-04 www.vishay.com 1 Package Information Vishay Siliconix PLCC: 2O-LEAD (POWER IC ONLY) D−SQUARE A2 MILLIMETERS D1−SQUARE B1 B e1 D2 Document Number: 72812 28-Jan-04 INCHES Min Max Min Max 4.20 4.57 0.165 0.180 2.29 3.04 0.090 0.120 0.51 − 0.020 − 0.331 0.553 0.013 0.021 0.661 0.812 0.026 0.032 9.78 10.03 0.385 0.395 8.890 9.042 0.350 0.356 7.37 8.38 0.290 0.330 1.27 BSC 0.050 BSC ECN: S-40081—Rev. A, 02-Feb-04 DWG: 5917 A1 A Dim A A1 A2 B B1 D D1 D2 e1 0.101 mm 0.004″ www.vishay.com 1 Package Information Vishay Siliconix PDIP: 14-LEAD (POWER IC ONLY) 14 13 12 11 10 9 8 E E1 1 2 3 4 5 6 7 D S Q1 A A1 B1 e1 L B Dim A A1 B B1 C D E E1 e1 eA L Q1 S 15° MAX C eA MILLIMETERS Min Max INCHES Min Max 3.81 5.08 0.150 0.200 0.38 1.27 0.015 0.050 0.38 0.51 0.015 0.020 0.89 1.65 0.035 0.065 0.20 0.30 0.008 0.012 17.27 19.30 0.680 0.760 7.62 8.26 0.300 0.325 5.59 7.11 0.220 0.280 2.29 2.79 0.090 0.110 7.37 7.87 0.290 0.310 2.79 3.81 0.110 0.150 1.27 2.03 0.050 0.080 1.02 2.03 0.040 0.080 ECN: S-40081—Rev. A, 02-Feb-04 DWG: 5919 Document Number: 72814 28-Jan-04 www.vishay.com 1 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000