SIP32459DB-T2-GE1

SiP32458, SiP32459 www.vishay.com Vishay Siliconix 20 m, Slew Rate Controlled Load Switch in WCSP6 DESCRIPTION FEATURES SiP32458 and SiP32459 are slew rate controlled integrated high side load switches that operate in the input voltage range from 1.5 V to 5.5 V. • Low input voltage, 1.5 V to 5.5 V • Low Ron, 20 m typical at 5 V • Slew rate control SiP32458 and SiP32459 are of p-channel MOSFET switching element with integrated gate pump that provides 20 m switch on resistance over a wide input voltage range. • Compatible with 1.2 V logic • Reverse current blocking when disabled (SiP32458, without output discharge switch) These devices have low voltage logic control threshold that can interface with low voltage control I/O directly without extra level shift or driver. A 2.8 M pulldown resistor is integrated at logic control EN pin. Available • Integrated output discharge switch (SiP32459 only) • Integrated pull down resistor at EN pin • 6 bumps WCSP package The slow slew rate of SiP32458 and SiP32459 in the range of 3 ms limits the in-rush current and minimized the switching noise. • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 The SiP32458 features a reverse current blocking capability while the SiP32459 features an integrated output discharge switch. APPLICATIONS • Battery operated devices • Smart phones Both SiP32458 and SiP32459 are available in compact wafer level WCSP package, WCSP6 1 mm x 1.5 mm with 0.5 mm pitch. • GPS and PMP • Computer • Medical and healthcare equipment • Industrial and instrument • Cellular phones and portable media players • Game console TYPICAL APPLICATION CIRCUIT VIN IN OUT IN VOUT OUT SiP32458, SiP32459 CIN COUT EN GND EN GND GND Fig. 1 - SiP32458 and SiP32459 Typical Application Circuit ORDERING INFORMATION TEMPERATURE RANGE -40 °C to +85 °C PACKAGE MARKING PART NUMBER WCSP: 6 bumps (2 x 3, 0.5 mm pitch, 250 μm bump height, 1.5 mm x 1 mm die size) AA SiP32458DB-T2-GE1 AB SiP32459DB-T2-GE1 Note • -GE1 denotes halogen-free and RoHS-compliant S20-0528-Rev. C, 06-Jul-2020 Document Number: 63999 1 For technical questions, contact: powerictechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiP32458, SiP32459 www.vishay.com Vishay Siliconix ABSOLUTE MAXIMUM RATINGS PARAMETER Supply input voltage (VIN) Enable input voltage (VEN) Output voltage (VOUT) Maximum continuous switch current (Imax.) Maximum pulsed current (IDM) VIN (pulsed at 1 ms, 10 % duty cycle) ESD rating (HBM) Junction temperature (TJ) Thermal resistance (JA) a Power dissipation (PD) a LIMIT -0.3 to 6 -0.3 to 6 -0.3 to 6 3 6 4000 -40 to +150 110 500 UNIT V A V °C °C/W mW Notes a. Device mounted with all bumps soldered to PC board b. Derate 9.1 mW/°C above TA = 70 °C  Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating/conditions for extended periods may affect device reliability. RECOMMENDED OPERATING RANGE PARAMETER Input voltage range (VIN) Operating junction temperature range LIMIT UNIT 1.5 to 5.5 V -40 to +125 °C SPECIFICATIONS PARAMETER SYMBOL Operating voltage c VIN Quiescent current IQ Off supply current IQ(off) Off switch current IDS(off) IRB Reverse blocking current On-resistance RDS(on) On-resistance temp. coefficient TCRDS TEST CONDITIONS UNLESS SPECIFIED VIN = 1.5 V to 5.5 V, TA = -40 °C to +85 °C (typical values are at VIN = 4.5 V, TA = 25 °C) VEN = VIN, OUT = open SiP32458 LIMITS UNIT TYP. b MAX. a 1.5 - 5.5 - 4.2 9.5 MIN. a - - 1 - - 10 EN = GND, OUT = 0 V - - 10 VOUT = 2.5 V, VIN = 0.75 V, VEN = 0 V (SiP32458 only) - - 10 SiP32459 EN = GND, OUT = open VIN = 1.5 V, IL = 500 mA, TA = 25 °C - 30 36 - 26 32 VIN = 3.3 V, IL = 500 mA, TA = 25 °C - 20 26 VIN = 5 V, IL = 1 A, TA = 25 °C - 20 26 - 2820 - ppm/°C - 70 - W RPD EN input low voltage c VIL VIN = 1.5 V - - 0.4 EN input high voltage c VIH VIN = 5.5 V 1 - - EN input leakage IEN EN pulldown resistor REN Output turn-on delay time td(on) Output turn-on rise time Output turn-off delay time tr td(off) μA VIN = 1.8 V, IL = 500 mA, TA = 25 °C VIN = 3.3 V, IOUT = 5 mA, VEN = 0 V (SiP32459 only) Output pulldown resistance V VIN = 5.5 V, VEN = 0 V - - 1 VIN = 5.5 V, VEN = 1.2 V - 0.44 1 VIN = 5.5 V, VEN = 1.2 V VIN = 4.5 V, RLOAD = 5 , CL = 100 μF, TA = 25 °C - 2.8 - - 0.5 - - 3 - - 18 - m V μA M ms μs Notes a. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum b. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing c. For VIN outside this range consult typical EN threshold curve S20-0528-Rev. C, 06-Jul-2020 Document Number: 63999 2 For technical questions, contact: powerictechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiP32458, SiP32459 www.vishay.com Vishay Siliconix PIN CONFIGURATION 1 OUT A OUT B GND C 2 W AA IN IN A2 A1 OUT IN IN B2 B1 OUT EN EN C2 C1 GND Backside Bumpside Fig. 2 - WCSP 2 x 3 Package PIN DESCRIPTION PIN NUMBER NAME A1, B1 OUT C1 GND FUNCTION These are the output pins of the switch Ground connection A2, B2 IN These are input pins of the switch C2 EN Enable input BLOCK DIAGRAM Fig. 3 - Functional Block Diagram S20-0528-Rev. C, 06-Jul-2020 Document Number: 63999 3 For technical questions, contact: powerictechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiP32458, SiP32459 www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (internally regulated, 25 °C, unless otherwise noted) 7 1000 SiP32458 IQ(OFF) - Off Supply Current (nA) IQ - Quiescent Current (μA) 6 5 4 3 2 1 VIN = 5.5 V 10 VIN = 4.5 V 1 VIN = 3.6 V 0.1 0.01 VIN = 2.5 V VIN = 1.2 V 0 0.001 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VIN - Input Voltage (V) - 40 20 40 Temperature (°C) Fig. 4 - Quiescent Current vs. Input Voltage Fig. 7 - Off Supply Current vs. Temperature 18 - 20 0 60 80 100 700 SiP32459 16 600 SiP32458 14 IQ(OFF) - Off Supply Current (nA) IQ(OFF) - Off Supply Current (nA) 100 12 10 8 6 4 500 400 300 200 100 2 0 0 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 VIN - Inport Voltage (V) 5.0 1.0 5.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VIN - Input Voltage (V) Fig. 8 - Off Supply Current vs. Input Voltage Fig. 5 - Off Supply Current vs. Input Voltage 7 700 VIN = 5.5 V 600 IDS(off) - Off Switch Current (nA) 6 IQ - Quiescent Current (μA) 1.5 5 VIN = 4.5 V 4 VIN = 3.6 V 3 VIN = 2.5 V 2 VIN = 1.2 V 500 400 300 200 100 1 0 0 1.0 - 40 - 20 0 20 40 Temperature (°C) 60 80 Fig. 6 - Quiescent Current vs. Temperature S20-0528-Rev. C, 06-Jul-2020 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 100 VIN - Input Voltage (V) Fig. 9 - Off Switch Current vs. Input Voltage Document Number: 63999 4 For technical questions, contact: powerictechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiP32458, SiP32459 www.vishay.com Vishay Siliconix 40 25 38 24 36 23 RDS - On-Resistance (mΩ) RDS - On-Resistance (mΩ) TYPICAL CHARACTERISTICS (internally regulated, 25 °C, unless otherwise noted) 34 32 30 IO = 3.0 A 28 IO = 2.0 A 26 IO = 1.0 A 24 22 22 21 20 19 18 17 20 IO = 0.1 A 16 18 IO = 0.5 A 16 1.0 1.5 2.0 2.5 3.0 15 3.5 4.0 4.5 5.0 - 40 5.5 - 20 0 20 40 60 80 VIN - Input Voltage (V) Temperature (°C) Fig. 10 - RDS(on) vs. Input Voltage Fig. 13 - RDS(on) vs. Temperature 10000 100 0 VIN = 5.5 V SiP32459 - 20 1000 SiP32458 IIN - Input Current (nA) IQ(OFF) - Off Supply Current (nA) IO = 0.5 A VIN = 4.5 V VIN = 4.5 V 100 VIN = 3.6 V 10 VIN = 2.5 V 1 0.1 VIN = 1.2 V - 40 VIN = 0.75V - 60 - 80 - 100 - 120 - 140 0.01 - 40 - 20 0 20 40 60 80 0.5 100 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VOUT - Output Voltage (V) Temperature (°C) Fig. 11 - Off Supply Current vs. Temperature Fig. 14 - Reverse Blocking Current vs. Output Voltage 50 10000 1000 0 IIN - Input Current (nA) IDS(off) - Off Switch Current (nA) SiP32458 VIN = 5.5 V VIN = 4.5 V 100 VIN = 3.6 V 10 1 VIN = 2.5 V 0.1 VOUT = 2.5 A VIN = 0.75 V -50 -100 -150 -200 -250 VIN = 1.2 V 0.01 -300 - 40 - 20 0 20 40 60 80 100 Temperature (°C) Fig. 12 - Off Switch Current vs. Temperature S20-0528-Rev. C, 06-Jul-2020 - 40 - 20 0 20 40 60 80 100 Temperature (°C) Fig. 15 - Reverse Blocking Current vs. Temperature Document Number: 63999 5 For technical questions, contact: powerictechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiP32458, SiP32459 www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (internally regulated, 25 °C, unless otherwise noted) 85 4.00 VIN = 4.5 V CL = 100 μF RL = 5 Ω 3.75 80 VIN = 3.3 V IOUT = 5 mA 3.50 75 tr - Rise Time (ms) RPD - Output Pulldown Resistance (Ω) SiP32459 70 65 60 3.25 3.00 2.75 2.50 2.25 2.00 55 - 40 - 20 0 20 40 60 80 - 40 100 - 20 0 20 60 80 100 Temperature (°C) Temperature (°C) Fig. 19 - Rise Time vs. Temperature Fig. 16 - Output Pulldown Resistance vs. Temperature 24.00 0.9 0.85 VIN = 4.5 V CL = 100 μF RL = 5 Ω td(off) - Turn-Off Delay Time (μs) 22.00 0.8 EN Threshold Voltage (V) 40 VIH 0.75 VIL 0.7 0.65 0.6 0.55 0.5 20.00 18.00 16.00 14.00 12.00 0.45 10.00 - 40 0.4 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 0 20 40 60 80 100 VIN - Input Voltage(V) Temperature (°C) Fig. 17 - EN Threshold Voltage vs. Input Voltage Fig. 20 - Turn-Off Delay Time vs. Temperature 2.00 1 0.8 VIN = 4.5 V CL = 100 μF RL = 150 Ω 1.80 VIN = 4.5 V CL = 100 μF RL = 5 Ω td(off) - Turn-Off Delay Time (ms) td(on) - Turn-On Delay Time (ms) - 20 0.6 0.4 0.2 1.60 SiP32458 1.40 1.20 1.00 SiP32459 0.80 0.60 0.40 0.20 0 0.00 - 40 - 20 0 20 40 60 80 100 Temperature (°C) Fig. 18 - Turn-On Delay Time vs. Temperature S20-0528-Rev. C, 06-Jul-2020 - 40 - 20 0 20 40 60 80 100 Temperature (°C) Fig. 21 - Turn-Off Delay Time vs. Temperature Document Number: 63999 6 For technical questions, contact: powerictechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiP32458, SiP32459 www.vishay.com Vishay Siliconix TYPICAL WAVEFORMS Fig. 22 - Turn-On Time Fig. 25 - Turn-Off Time, SiP32458 Fig. 23 - Turn-Off Time Fig. 26 - Turn-Off Time, SiP32459 Fig. 24 - Turn-On Time S20-0528-Rev. C, 06-Jul-2020 Document Number: 63999 7 For technical questions, contact: powerictechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiP32458, SiP32459 www.vishay.com DETAILED DESCRIPTION SiP32458 and SiP32459 are p-channel power MOSFET designed as high side load switches. They incorporate a negative charge pump at the gate to keep the gate to source voltage high when turned on therefore keep the on resistance low at lower input voltage range. SiP32458 and SiP32459 are designed with slow slew rate to minimize the inrush current during turn on. The SiP32458 has a reverse blocking circuit to prevent the current from going back to the input in case the output voltage is higher than the input voltage. The SiP32459 has an output pulldown resistor to discharge the output capacitance when the device is off. APPLICATION INFORMATION Input Capacitor While a bypass capacitor on the input is not required, a 4.7 μF or larger capacitor for CIN is recommended in almost all applications. The bypass capacitor should be placed as physically close as possible to the input pin to be effective in minimizing transients on the input. Ceramic capacitors are recommended over tantalum because of their ability to withstand input current surges from low impedance sources such as batteries in portable devices. Output Capacitor Vishay Siliconix another limiting characteristic for the safe operating load current is the thermal power dissipation of the package. To obtain the highest power dissipation (and a thermal resistance of 110 °C/W) the device should be connected to a heat sink on the printed circuit board. The maximum power dissipation in any application is dependent on the maximum junction temperature, TJ (max.) = 125 °C, the junction-to-ambient thermal resistance, J-A = 110 °C/W, and the ambient temperature, TA, which may be formulaically expressed as: 125 - T A T J(max.) - T A P (max.) = -------------------------------- = ---------------------- JA 280 It then follows that, assuming an ambient temperature of 70 °C, the maximum power dissipation will be limited to about 500 mW. So long as the load current is below the 3 A limit, the maximum continuous switch current becomes a function two things: the package power dissipation and the RDS(on) at the ambient temperature. As an example let us calculate the worst case maximum load current at TA = 70 °C. The worst case RDS(on) at 25 °C is 36 m at VIN = 1.5 V. The RDS(on) at 70 °C can be extrapolated from this data using the following formula: A 0.1 μF capacitor across VOUT and GND is recommended to insure proper slew operation. There is inrush current through the output MOSFET and the magnitude of the inrush current depends on the output capacitor, the bigger the COUT the higher the inrush current. There are no ESR or capacitor type requirement. Where TC is 2820 ppm/°C. Continuing with the calculation we have Enable The maximum current limit is then determined by The EN pin is compatible with CMOS logic voltage levels. It requires at least 0.4 V or below to fully shut down the device and 1 V or above to fully turn on the device. There is a 2.8 M resistor connected between EN pin and GND pin. Protection Against Reverse Voltage Condition The SiP32458 contains the reverse blocking circuit to keep the output current from flowing back to the input in case the output voltage is higher than the input voltage. Thermal Considerations These devices are designed to maintain a constant output load current. Due to physical limitations of the layout and assembly of the device the maximum switch current is 3 A as stated in the Absolute Maximum Ratings table. However, S20-0528-Rev. C, 06-Jul-2020 RDS(on) (at 70 °C) = RDS(on) (at 25 °C) x (1 + TC x T) RDS(on) (at 70 °C) = 36 m x (1 + 0.00282 x (70 °C - 25 °C)) = 40.5 m P (max.) I LOAD(max.)  --------------------R DS(on) which in this case is 3.5 A. Under the stated input voltage condition, if the 3.5 A current limit is exceeded the internal die temperature will rise and eventually, possibly damage the device. To avoid possible permanent damage to the device and keep a reasonable design margin, it is recommended to operate the device maximum up to 3 A only as listed in the Absolute Maximum Ratings table.  Document Number: 63999 8 For technical questions, contact: powerictechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SiP32458, SiP32459 www.vishay.com Vishay Siliconix PRODUCT SUMMARY Part number SiP32458 SiP32459 Description 1.5 V to 5.5 V, 20 m, bidirectional off isolation 1.5 V to 5.5 V, 20 m, output discharge Configuration Single Single Slew rate time (μs) 3000 3000 On delay time (μs) 500 500 Input voltage min. (V) 1.5 1.5 Input voltage max. (V) 5.5 5.5 On-resistance at input voltage min. (m) 30 30 On-resistance at input voltage max. (m) 20 20 Quiescent current at input voltage min. (μA) 1.5 1.5 Quiescent current at input voltage max. (μA) 5.8 5.8 Output discharge (yes / no) No Yes Reverse blocking (yes / no) Yes No Continuous current (A) Package type Package size (W, L, H) (mm) 3 3 WCSP6 WCSP6 1.0 x 1.5 x 0.5 1.0 x 1.5 x 0.5 Status code 2 2 Product type Slew rate Slew rate Applications Computers, consumer, industrial, healthcare, networking, portable Computers, consumer, industrial, healthcare, networking, portable Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see www.vishay.com/ppg?63999. S20-0528-Rev. C, 06-Jul-2020 Document Number: 63999 9 For technical questions, contact: powerictechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Package Information www.vishay.com Vishay Siliconix WCSP6: 6 Bumps (2 x 3, 0.5 mm pitch, 250 μm bump height, 1 mm x 1.5 mm die size) b C2 B2 A2 C1 B1 A1 s e D W AB s Index Bump A1 s E e e Bottom View A1 A A1 Note 3 e Note 4 Top View e s Bump Note 2 Side View e RECOMMENDED LAND PATTERN MILLIMETERS (5) INCHES DIMENSION MIN. NOM. MAX. MIN. NOM. MAX. 0.0244 A 0.540 0.572 0.620 0.0212 0.0225 A1 0.214 0.250 0.286 0.0084 0.0098 0.0113 b 0.279 0.310 0.372 0.0109 0.0122 0.0146 e 0.500 0.0197 s 0.230 0.250 0.270 0.0090 0.0098 D 0.920 0.960 1.000 0.0362 0.0378 0.0106 0.0394 E 1.420 1.460 1.500 0.0559 0.0575 0.0591 Notes (unless otherwise specified) (1) Laser mark on the silicon die back coated with an epoxy film. (2) Bumps are SAC396. (3) 0.050 max. co-planarity. (4) Laminate tape thickness is 0.022 mm. (5) Use millimeters as the primary measurement. ECN: S13-1424-Rev. B, 01-Jul-13 DWG: 6011 Revision: 01-Jul-13 Document Number: 62805 1 For technical questions, contact: powerictechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000