AD9775BSV

14-Bit, 160 MSPS, 2×/4×/8× Interpolating Dual TxDAC+® Digital-to-Analog Converter AD9775 FEATURES Versatile input data interface Twos complement/straight binary data coding Dual-port or single-port interleaved input data Single 3.3 V supply operation Power dissipation: 1.2 W @ 3.3 V typical On-chip, 1.2 V reference 80-lead, thin quad flat package, exposed pad (TQFP_EP) 14-bit resolution, 160 MSPS/400 MSPS input/output data rate Selectable 2×/4×/8× interpolating filter Programmable channel gain and offset adjustment fS/4, fS/8 digital quadrature modulation capability Direct IF transmission mode for 70 MHz + IFs Enables image rejection architecture Fully compatible SPI® port Excellent ac performance SFDR: −71 dBc @ 2 MHz to 35 MHz W-CDMA ACPR: −71 dB @ IF = 19.2 MHz Internal PLL clock multiplier Selectable internal clock divider Versatile clock input Differential/single-ended sine wave or TTL/CMOS/LVPECL compatible APPLICATIONS Communications Analog quadrature modulation architecture 3G, multicarrier GSM, TDMA, CDMA systems Broadband wireless, point-to-point microwave radios Instrumentation/ATE FUNCTIONAL BLOCK DIAGRAM IDAC COS AD9775 I AND Q NONINTERLEAVED OR INTERLEAVED DATA 14 WRITE SELECT HALFBAND FILTER3* GAIN DAC OFFSET DAC SIN I LATCH 16 Q LATCH 16 MUX CONTROL HALFBAND FILTER2* 16 16 16 fDAC/2, 4, 8 16 16 SIN 16 FILTER BYPASS MUX IMAGE REJECTION/ DUAL DAC MODE BYPASS MUX I/Q DAC GAIN/OFFSET REGISTERS IOFFSET 14 HALFBAND FILTER1* VREF DATA ASSEMBLER COS IDAC /2 IOUT (fDAC) CLOCK OUT /2 /2 /2 SPI INTERFACE AND CONTROL REGISTERS DIFFERENTIAL CLK PHASE DETECTOR AND VCO PLL CLOCK MULTIPLIER AND CLOCK DIVIDER 02858-001 * HALF-BAND FILTERS ALSO CAN BE CONFIGURED FOR ZERO STUFFING ONLY PRESCALER Figure 1. Rev. E Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2006 Analog Devices, Inc. All rights reserved. AD9775 TABLE OF CONTENTS Features .............................................................................................. 1 1R/2R Mode ................................................................................ 25 Applications....................................................................................... 1 Clock Input Configurations...................................................... 25 Functional Block Diagram .............................................................. 1 Programmable PLL .................................................................... 26 Revision History ............................................................................... 3 Power Dissipation....................................................................... 27 General Description ......................................................................... 4 Sleep/Power-Down Modes........................................................ 28 Product Highlights ....................................................................... 4 Two-Port Data Input Mode ...................................................... 28 Specifications..................................................................................... 5 PLL Enabled, Two-Port Mode .................................................. 28 DC Specifications ......................................................................... 5 DATACLK Inversion.................................................................. 29 Dynamic Specifications ............................................................... 6 DATACLK Driver Strength....................................................... 29 Digital Specifications ................................................................... 7 PLL Enabled, One-Port Mode .................................................. 29 Digital Filter Specifications ......................................................... 8 ONEPORTCLK Inversion......................................................... 29 Absolute Maximum Ratings............................................................ 9 ONEPORTCLK Driver Strength.............................................. 30 ESD Caution.................................................................................. 9 IQ Pairing .................................................................................... 30 Thermal Resistance ...................................................................... 9 PLL Disabled, Two-Port Mode................................................. 30 Pin Configuration and Function Descriptions........................... 10 PLL Disabled, One-Port Mode ................................................. 30 Typical Performance Characteristics ........................................... 12 Digital Filter Modes ................................................................... 31 Terminology .................................................................................... 17 Amplitude Modulation.............................................................. 31 Mode Control (via SPI Port) ......................................................... 18 Modulation, No Interpolation .................................................. 32 Register Descriptions ..................................................................... 19 Modulation, Interpolation = 2× ............................................... 33 Address 0x00 ............................................................................... 19 Modulation, Interpolation = 4× ............................................... 34 Address 0x01 ............................................................................... 19 Modulation, Interpolation = 8× ............................................... 35 Address 0x02 ............................................................................... 19 Zero Stuffing ............................................................................... 36 Address 0x03 ............................................................................... 20 Interpolating (Complex Mix Mode)........................................ 36 Address 0x04 ............................................................................... 20 Operations on Complex Signals............................................... 36 Address 0x05, Address 0x09 ..................................................... 20 Complex Modulation and Image Rejection of Baseband Signals .......................................................................................... 37 Address 0x06, Address 0x0A..................................................... 20 Address 0x07, Address 0x0B ..................................................... 20 Address 0x08, Address 0x0C..................................................... 20 Address 0x08, Address 0x0C..................................................... 20 Functional Description .................................................................. 21 Serial Interface for Register Control ........................................ 21 General Operation of the Serial Interface ............................... 21 Image Rejection and Sideband Suppression of Modulated Carriers ........................................................................................ 38 Applying the Output Configurations........................................... 42 Unbuffered Differential Output, Equivalent Circuit ............. 42 Differential Coupling Using a Transformer............................ 42 Differential Coupling Using an Op Amp................................ 43 Instruction Byte .......................................................................... 22 Interfacing the AD9775 with the AD8345 Quadrature Modulator.................................................................................... 43 Serial Interface Port Pin Descriptions ..................................... 22 Evaluation Board ............................................................................ 44 MSB/LSB Transfers..................................................................... 22 Outline Dimensions ....................................................................... 54 Notes on Serial Port Operation ................................................ 22 Ordering Guide .......................................................................... 54 DAC Operation........................................................................... 24 Rev. E | Page 2 of 56 AD9775 REVISION HISTORY 12/06—Rev. D to Rev. E Changes to Figure 52, Figure 54, Figure 55, and Figure 56 .......29 1/06—Rev. C to Rev. D Updated Formatting..........................................................Universal Changes to Figure 32 .................................................................... 22 Changes to Figure 108 .................................................................. 55 Updated Outline Dimensions...................................................... 58 Changes to Ordering Guide......................................................... 58 6/04—Rev. B to Rev. C Updated Layout .................................................................Universal Changes to DC Specifications ....................................................... 5 Changes to Absolute Maximum Ratings...................................... 9 Changes to the DAC Operation Section .................................... 25 Inserted Figure 38.......................................................................... 25 Changes to Figure 40 .................................................................... 26 Changes to Table 11 ...................................................................... 28 Changes to Programmable PLL Section..................................... 28 Changes to Figures 49, 50, and 51............................................... 29 Changes to the PLL Enabled, One-Port Mode Section............ 30 Changes to the PLL Disabled, One-Port Mode Section........... 31 Changes to the Ordering Guide .................................................. 57 Updated Outline Dimensions...................................................... 57 3/03—Rev. A to Rev. B Changes to Register Description—Address 04h ....................... 16 Changes to Equation 1.................................................................. 16 Changes to Figure 8....................................................................... 20 2/03—Rev. 0 to Rev. A Edits to Features ...............................................................................1 Edits to DC Specifications ..............................................................3 Edits to Dynamic Specifications ....................................................4 Edits to Pin Function Descriptions ...............................................8 Edits to Table I ............................................................................... 14 Edits to Register Description—Address 02h ............................. 15 Edits to Register Description—Address 03h ............................. 16 Edits to Register Description—Address 07h, 0Bh.................... 16 Edits to Equation 1........................................................................ 16 Edits to MSB/LSB Transfers......................................................... 18 Edits to Programmable PLL......................................................... 21 Added New Figure 14 ................................................................... 22 Renumbered Figures 15–69 ......................................................... 22 Added Two-Port Data Input Mode Section............................... 23 Edits to PLL Enabled, Two-Port Mode ...................................... 24 Edits to Figure 19 .......................................................................... 24 Edits to Figure 21 .......................................................................... 25 Edits to PLL Disabled, Two-Port Mode ..................................... 25 Edits to Figure 22 .......................................................................... 25 Edits to Figure 23 .......................................................................... 26 Edits to Figure 26a ........................................................................ 27 Edits to Complex Modulation and Image Rejection of Baseband Signals ............................................................................................. 31 Edits to Evaluation Board ............................................................ 39 Edits to Figures 56–59 .................................................................. 40 Replaced Figures 60–69................................................................ 42 Updated Outline Dimensions...................................................... 49 Rev. E | Page 3 of 56 AD9775 GENERAL DESCRIPTION The AD97751 is the 14-bit member of the AD977x pincompatible, high performance, programmable 2×/4×/8× interpolating TxDAC+ family. The AD977x family features a serial port interface (SPI) that provides a high level of programmability, thus allowing for enhanced system-level options. These options include selectable 2×/4×/8× interpolation filters; fS/2, fS/4, or fS/8 digital quadrature modulation with image rejection; a direct IF mode; programmable channel gain and offset control; programmable internal clock divider; straight binary or twos complement data interface; and a single-port or dual-port data interface. The selectable 2×/4×/8× interpolation filters simplify the requirements of the reconstruction filters while simultaneously enhancing the pass-band noise/distortion performance of TxDAC+ devices. The independent channel gain and offset adjust registers allow the user to calibrate LO feedthrough and sideband suppression errors associated with analog quadrature modulators. The 6 dB of gain adjustment range can also be used to control the output power level of each DAC. The AD9775 can perform fS/2, fS/4, and fS/8 digital modulation and image rejection when combined with an analog quadrature modulator. In this mode, the AD9775 accepts I and Q complex data (representing a single or multicarrier waveform), generates a quadrature modulated IF signal along with its orthogonal representation via its dual DACs, and presents these two reconstructed orthogonal IF carriers to an analog quadrature modulator to complete the image rejection upconversion process. Another digital modulation mode (that is, the direct IF mode) allows the original baseband signal representation to be frequency translated such that pairs of images fall at multiples of one-half the DAC update rate. The AD977x family includes a flexible clock interface that accepts differential or single-ended sine wave or digital logic inputs. An internal PLL clock multiplier is included and generates the necessary on-chip high frequency clocks. It can also be disabled to allow the use of a higher performance external clock source. An internal programmable divider simplifies clock generation in the converter when using an external clock source. A flexible data input interface allows for straight binary or twos complement formats and supports single-port interleaved or dual-port data. Dual high performance DAC outputs provide a differential current output programmable over a 2 mA to 20 mA range. 1 The AD9775 is manufactured on an advanced 0.35 micron CMOS process, operates from a single supply of 3.1 V to 3.5 V, and consumes 1.2 W of power. Targeted at wide dynamic range, multicarrier and multistandard systems, the superb baseband performance of the AD9775 is ideal for wideband CDMA, multicarrier CDMA, multicarrier TDMA, multicarrier GSM, and high performance systems employing high order QAM modulation schemes. The image rejection feature simplifies and can help reduce the number of signal band filters needed in a transmit signal chain. The direct IF mode helps to eliminate a costly mixer stage for a variety of communications systems. PRODUCT HIGHLIGHTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. The AD9775 is the 14-bit member of the AD977x pincompatible, high performance, programmable 2×/4×/8× interpolating TxDAC+ family. Direct IF transmission capability for 70 MHz + IFs through a novel digital mixing process. fS/2, fS/4, and fS/8 digital quadrature modulation and userselectable image rejection to simplify/remove cascaded SAW filter stages. A 2×/4×/8× user-selectable, interpolating filter eases data rate and output signal reconstruction filter requirements. User-selectable, twos complement/straight binary data coding. User-programmable, channel gain control over 1 dB range in 0.01 dB increments. User programmable channel offset control ±10% over the FSR. Ultrahigh speed 400 MSPS DAC conversion rate. Internal clock divider provides data rate clock for easy interfacing. Flexible clock input with single-ended or differential input, CMOS, or 1 V p-p LO sine wave input capability. Low power: complete CMOS DAC operates on 1.2 W from a 3.1 V to 3.5 V single supply. The 20 mA full-scale current can be reduced for lower power operation and several sleep functions are provided to reduce power during idle periods. On-chip voltage reference. The AD9775 includes a 1.20 V temperature compensated band gap voltage reference. 80-lead, thin quad flat package, exposed pad (TQFP_EP). Protected by U.S. Patent Numbers 5,568,145; 5,689,257; and 5,703,519. Other patents pending. Rev. E | Page 4 of 56 AD9775 SPECIFICATIONS DC SPECIFICATIONS TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, DVDD = 3.3 V, PLLVDD = 3.3 V, IOUTFS = 20 mA, unless otherwise noted. Table 1. Parameter RESOLUTION DC Accuracy 1 Integral Nonlinearity Differential Nonlinearity ANALOG OUTPUT (for 1R and 2R Gain Setting Modes) Offset Error Gain Error (with Internal Reference) Gain Matching Full-Scale Output Current 2 Output Compliance Range Output Resistance Output Capacitance Gain, Offset Cal DACs, Monotonicity Guaranteed REFERENCE OUTPUT Reference Voltage Reference Output Current 3 REFERENCE INPUT Input Compliance Range Reference Input Resistance Small Signal Bandwidth TEMPERATURE COEFFICIENTS Offset Drift Gain Drift (with Internal Reference) Reference Voltage Drift POWER SUPPLY AVDD Voltage Range Analog Supply Current (IAVDD) 4 IAVDD in SLEEP Mode CLKVDD Voltage Range Clock Supply Current (ICLKVDD)4 CLKVDD (PLL ON) Clock Supply Current (ICLKVDD) DVDD Voltage Range Digital Supply Current (IDVDD)4 Nominal Power Dissipation PDIS 5 PDIS IN PWDN Power Supply Rejection Ratio—AVDD OPERATING RANGE Min 14 Typ Max Unit Bits −5 −3 ±1.5 ±1.0 +5 +3 LSB LSB −0.02 −1.0 −1.0 2 −1.0 ±0.01 +0.02 +1.0 +1.0 20 +1.25 % of FSR % of FSR % of FSR mA V kΩ pF 1.26 V nA 1.25 7 0.5 V kΩ MHz 0 50 ±50 ppm of FSR/°C ppm of FSR/°C ppm/°C ±0.1 200 3 1.14 1.20 100 0.1 3.1 3.3 72.5 23.3 3.5 76 26 V mA mA 3.1 3.3 8.5 3.5 10.0 V mA 23.5 3.1 −40 1 Measured at IOUTA driving a virtual ground. Nominal full-scale current, IOUTFS, is 32 × the IREF current. Use an external amplifier to drive any external load. 4 100 MSPS fDAC with fOUT = 1 MHz, all supplies = 3.3 V, no interpolation, no modulation. 5 400 MSPS fDAC = 50 MSPS, fS/2 modulation, PLL enabled. 2 3 Rev. E | Page 5 of 56 3.3 34 380 1.75 6.0 ±0.4 mA 3.5 41 410 +85 V mA mW W mW % of FSR/V °C AD9775 DYNAMIC SPECIFICATIONS TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, DVDD = 3.3 V, PLLVDD = 0 V, IOUTFS = 20 mA, interpolation = 2×, differential transformer-coupled output, 50 Ω doubly terminated, unless otherwise noted. Table 2. Parameter DYNAMIC PERFORMANCE Maximum DAC Output Update Rate (fDAC) Output Settling Time (tST) to 0.025% Output Rise Time 10% to 90% 1 Output Fall Time 10% to 90%1 Output Noise, IOUTFS = 20 mA AC LINEARITY—BASEBAND MODE Spurious-Free Dynamic Range (SFDR) to Nyquist (fOUT = 0 dBFS) fDATA = 100 MSPS, fOUT = 1 MHz fDATA = 65 MSPS, fOUT = 1 MHz fDATA = 65 MSPS, fOUT = 15 MHz fDATA = 78 MSPS, fOUT = 1 MHz fDATA = 78 MSPS, fOUT = 15 MHz fDATA = 160 MSPS, fOUT = 1 MHz fDATA = 160 MSPS, fOUT = 15 MHz Spurious-Free Dynamic Range Within a 1 MHz Window fOUT = 0 dBFS, fDATA = 100 MSPS, fOUT = 1 MHz Two-Tone Intermodulation (IMD) to Nyquist (fOUT1 = fOUT2 = −6 dBFS) fDATA = 65 MSPS, fOUT1 = 10 MHz; fOUT2 = 11 MHz fDATA = 65 MSPS, fOUT1 = 20 MHz; fOUT2 = 21 MHz fDATA = 78 MSPS, fOUT1 = 10 MHz; fOUT2 = 11 MHz fDATA = 78 MSPS, fOUT1 = 20 MHz; fOUT2 = 21 MHz fDATA = 160 MSPS, fOUT1 = 10 MHz; fOUT2 = 11 MHz fDATA = 160 MSPS, fOUT1 = 20 MHz; fOUT2 = 21 MHz Total Harmonic Distortion (THD) fDATA = 100 MSPS, fOUT = 1 MHz; 0 dBFS Signal-to-Noise Ratio (SNR) fDATA = 78 MSPS, fOUT = 5 MHz; 0 dBFS fDATA = 160 MSPS, fOUT = 5 MHz; 0 dBFS Adjacent Channel Power Ratio (ACPR) W-CDMA with 3.84 MHz BW, 5 MHz Channel Spacing IF = Baseband, fDATA = 76.8 MSPS IF = 19.2 MHz, fDATA = 76.8 MSPS Four-Tone Intermodulation 21 MHz, 22 MHz, 23 MHz, and 24 MHz at −12 dBFS (fDATA = MSPS, Missing Center) AC LINEARITY—IF MODE Four-Tone Intermodulation at IF = 200 MHz 201 MHz, 202 MHz, 203 MHz, and 204 MHz at −12 dBFS (fDATA = 160 MSPS, fDAC = 320 MHz) 1 Measured single-ended into 50 Ω load. Rev. E | Page 6 of 56 Min Typ 400 Max Unit 11 0.8 0.8 50 MSPS ns ns ns pA/√Hz 71 84.5 84 80 84 80 82 80 dBc dBc dBc dBc dBc dBc dBc 73 91.3 dBc 81 76 81 76 81 76 dBc dBc dBc dBc dBc dBc −82.5 dB 76 74 dB dB 71 71 dBc dBc 75 dBFS 72 dBFS −71 AD9775 DIGITAL SPECIFICATIONS TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, PLLVDD = 0 V, DVDD = 3.3 V, IOUTFS = 20 mA, unless otherwise noted. Table 3. Parameter DIGITAL INPUTS Logic 1 Voltage Logic 0 Voltage Logic 1 Current Logic 0 Current Input Capacitance CLOCK INPUTS Input Voltage Range Common-Mode Voltage Differential Voltage SERIAL CONTROL BUS Maximum SCLK Frequency (fSLCK) Minimum Clock Pulse Width High (tPWH) Minimum Clock Pulse Width Low (tPWL) Maximum Clock Rise/Fall Time Minimum Data/Chip Select Setup Time (tDS) Minimum Data Hold Time (tDH) Maximum Data Valid Time (tDV) RESET Pulse Width Inputs (SDI, SDIO, SCLK, CSB) Logic 1 Voltage Logic 0 Voltage Logic 1 Current Logic 0 Current Input Capacitance SDIO Output Logic 1 Voltage Logic 0 Voltage Logic 1 Current Logic 0 Current Min Typ 2.1 3 0 −10 −10 Max Unit 0.9 +10 +10 V V μA μA pF 5 0 0.75 0.5 1.5 1.5 3 2.25 15 30 30 1 25 0 30 1.5 2.1 3 0 −10 −10 0.9 +10 +10 5 DRVDD − 0.6 0.4 30 30 Rev. E | Page 7 of 56 50 50 V V V MHz ns ns ms ns ns ns ns V V μA μA pF V V mA mA AD9775 DIGITAL FILTER SPECIFICATIONS 20 Table 4. Half-Band Filter No. 1 (43 Coefficients) 0 ATTENUATION (dBFS) –20 –40 –60 –80 –100 0.5 1.0 1.5 2.0 02858-002 0 2.0 02858-003 –120 8 02858-004 Coefficient 8 0 −29 0 67 0 −134 0 244 0 −414 0 673 0 −1079 0 1772 0 −3280 0 10,364 16,384 fOUT (NORMALIZED TO INPUT DATA RATE) Figure 2. 2× Interpolating Filter Response 20 0 ATTENUATION (dBFS) Tap 1, 43 2, 42 3, 41 4, 40 5, 39 6, 38 7, 37 8, 36 9, 35 10, 34 11, 33 12, 32 13, 31 14, 30 15, 29 16, 28 17, 27 18, 26 19, 25 20, 24 21, 23 22 –20 –40 –60 –80 Table 5. Half-Band Filter No. 2 (19 Coefficients) Coefficient 19 0 −120 0 438 0 −1288 0 5,047 8,192 Table 6. Half-Band Filter No. 3 (11 Coefficients) Tap 1, 11 2, 10 3, 9 4, 8 5, 7 6 Coefficient 7 0 −53 0 302 512 –100 –120 0 0.5 1.0 1.5 fOUT (NORMALIZED TO INPUT DATA RATE) Figure 3. 4× Interpolating Filter Response 20 0 ATTENUATION (dBFS) Tap 1, 19 2, 18 3, 17 4, 16 5, 15 6, 14 7, 13 8, 12 9, 11 10 –20 –40 –60 –80 –100 –120 0 2 4 6 fOUT (NORMALIZED TO INPUT DATA RATE) Figure 4. 8× Interpolating Filter Response Rev. E | Page 8 of 56 AD9775 ABSOLUTE MAXIMUM RATINGS Table 7. Parameter AVDD, DVDD, CLKVDD AVDD, DVDD, CLKVDD AGND, DGND, CLKGND REFIO, FSADJ1/FSADJ2 IOUTA, IOUTB P1B13 to P1B0, P2B13 to P2B0, RESET DATACLK, PLL_LOCK CLK+, CLK– LPF SPI_CSB, SPI_CLK, SPI_SDIO, SPI_SDO Junction Temperature Storage Temperature Lead Temperature (10 sec) With Respect To AGND, DGND, CLKGND AVDD, DVDD, CLKVDD AGND, DGND, CLKGND AGND AGND DGND DGND CLKGND CLKGND DGND Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION Rating −0.3 V to +4.0 V −4.0 V to +4.0 V −0.3 V to +0.3 V −0.3 V to AVDD + 0.3 V −1.0 V to AVDD + 0.3 V −0.3 V to DVDD + 0.3 V −0.3 V to DVDD + 0.3 V −0.3 V to CLKVDD + 0.3 V −0.3 V to CLKVDD + 0.3 V −0.3 V to DVDD + 0.3 V 125°C −65°C to +150°C 300°C THERMAL RESISTANCE θJA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Table 8. Thermal Resistance Package Type 80-Lead Thin Quad Flat Package (TQFP_EP), Exposed Pad Rev. E | Page 9 of 56 θJA 23.5 Unit °C/W AD9775 AVDD AGND AVDD AGND AVDD AGND AGND IOUTB2 IOUTA2 AGND AGND IOUTB1 IOUTA1 AGND AGND AVDD AGND AVDD AGND AVDD PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 CLKVDD 1 60 FSADJ1 59 FSADJ2 CLKVDD 3 58 REFIO CLKGND 4 57 RESET CLK+ 5 56 SPI_CSB CLK– 6 55 SPI_CLK CLKGND 7 54 SPI_SDIO DATACLK/PLL_LOCK 8 53 SPI_SDO DGND 9 52 DGND 51 DVDD P1B13 (MSB) 11 50 NC P1B12 12 49 NC P1B11 13 48 P2B0 (LSB) P1B10 14 47 P2B1 P1B9 15 46 P2B2 P1B8 16 45 P2B3 DGND 17 44 DGND DVDD 18 43 DVDD P1B7 19 42 P2B4 P1B6 20 41 P2B5 LPF PIN 1 2 AD9775 TxDAC+ TOP VIEW (Not to Scale) DVDD 10 Figure 5. Pin Configuration Rev. E | Page 10 of 56 02858-005 P2B6 P2B7 P2B8 P2B9 DVDD DGND P2B10 P2B11 ONEPORTCLK/P2B12 IQSEL/P2B13 (MSB) NC NC P1B0 (LSB) P1B1 DVDD DGND P1B2 P1B3 P1B4 P1B5 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 NC = NO CONNECT AD9775 Table 9. Pin Function Descriptions Pin No. 1, 3 2 4, 7 5 6 8 Mnemonic CLKVDD LPF CLKGND CLK+ CLK− DATACLK/PLL_LOCK Description Clock Supply Voltage. PLL Loop Filter. Clock Supply Common. Differential Clock Input. Differential Clock Input. With the PLL enabled, this pin indicates the state of the PLL. A read of a Logic 1 indicates the PLL is in the locked state. Logic 0 indicates the PLL has not achieved lock. This pin may also be programmed to act as either an input or output (Address 02h, Bit 3) DATACLK signal running at the input data rate. Digital Common. Digital Supply Voltage. Port 1 Data Inputs. 9, 17, 25, 35, 44, 52 10, 18, 26, 36, 43, 51 11 to 16, 19 to 24, 27, 28 29, 30, 49, 50 31 DGND DVDD P1B13 (MSB) to P1B0 (LSB) NC IQSEL/P2B13 (MSB) 32 ONEPORTCLK/P2B12 33, 34, 37 to 42, 45 to 48 53 P2B11 to P2B0 (LSB) SPI_SDO 54 SPI_SDIO 55 SPI_CLK 56 SPI_CSB 57 RESET 58 59 60 61, 63, 65, 76, 78, 80 62, 64, 66, 67, 70, 71, 74, 75, 77, 79 68, 69 72, 73 REFIO FSADJ2 FSADJ1 AVDD AGND No Connect. In one-port mode, IQSEL = 1 followed by a rising edge of the differential input clock latches the data into the I channel input register. IQSEL = 0 latches the data into the Q channel input register. In two-port mode, this pin becomes the Port 2 MSB. With the PLL disabled and the AD9775 in one-port mode, this pin becomes a clock output that runs at twice the input data rate of the I and Q channels. This allows the AD9775 to accept and demux interleaved I and Q data to the I and Q input registers. Port 2 Data Inputs. In the case where SDIO is an input, SDO acts as an output. When SDIO becomes an output, SDO enters a High-Z state. This pin can also be used as an output for the data rate clock. For more information, see the Two-Port Data Input Mode section. Bidirectional Data Pin. Data direction is controlled by Bit 7 of Register Address 0x00. The default setting for this bit is 0, which sets SDIO as an input. Data input to the SPI port is registered on the rising edge of SPI_CLK. Data output on the SPI port is registered on the falling edge. Chip Select/SPI Data Synchronization. On momentary logic high, resets SPI port logic and initializes instruction cycle. Logic 1 resets all of the SPI port registers, including Address 0x00, to their default values. A software reset can also be done by writing a Logic 1 to SPI Register 00h, Bit 5. However, the software reset has no effect on the bit in Address 0x00. Reference Output, 1.2 V Nominal. Full-Scale Current Adjust, Q Channel. Full-Scale Current Adjust, I Channel. Analog Supply Voltage. Analog Common. IOUTB2, IOUTA2 IOUTB1, IOUTA1 Differential DAC Current Outputs, Q Channel. Differential DAC Current Outputs, I Channel. Rev. E | Page 11 of 56 AD9775 TYPICAL PERFORMANCE CHARACTERISTICS 10 10 0 0 –10 –10 –20 –20 AMPLITUDE (dBm) –30 –40 –50 –60 –30 –40 –50 –60 –70 –70 –80 –80 –90 65 130 FREQUENCY (MHz) 02858-006 –90 0 0 50 100 02858-009 AMPLITUDE (dBm) T = 25°C, AVDD = 3.3 V, CLKVDD = 3.3 V, DVDD = 3.3 V, IOUTFS = 20 mA, interpolation = 2×, differential transformer-coupled output, 50 Ω doubly terminated, unless otherwise noted. 150 FREQUENCY (MHz) Figure 6. Single-Tone Spectrum @ fDATA = 65 MSPS with fOUT = fDATA/3 Figure 9. Single-Tone Spectrum @ fDATA = 78 MSPS with fOUT = fDATA/3 90 90 0dBFS 0dBFS 85 85 –6dBFS 80 75 SFDR (dBc) –12dBFS 70 65 75 –12dBFS 70 –6dBFS 65 60 60 55 55 5 10 15 20 25 30 FREQUENCY (MHz) 02858-007 0 0 5 10 15 20 25 30 02858-010 50 50 30 02858-011 SFDR (dBc) 80 FREQUENCY (MHz) Figure 7. In-Band SFDR vs. fOUT @ fDATA = 65 MSPS Figure 10. In-Band SFDR vs. fOUT @ fDATA = 78 MSPS 90 90 –6dBFS 85 85 –6dBFS 80 75 75 SFDR (dBc) 80 70 –12dBFS 65 0dBFS 70 –12dBFS 65 60 60 55 55 50 50 0 5 10 15 20 25 FREQUENCY (MHz) 30 02858-008 SFDR (dBc) 0dBFS Figure 8. Out-of-Band SFDR vs. fOUT @ fDATA = 65 MSPS 0 5 10 15 20 25 FREQUENCY (MHz) Figure 11. Out-of-Band SFDR vs. fOUT @ fDATA = 78 MSPS Rev. E | Page 12 of 56 AD9775 10 90 –6dBFS 0 –3dBFS 85 –10 –30 IMD (dBc) AMPLITUDE (dBm) 80 –20 –40 –50 75 0dBFS 70 65 –60 60 –70 55 –80 –90 200 300 FREQUENCY (MHz) 0 5 10 15 20 25 30 FREQUENCY (MHz) Figure 12. Single-Tone Spectrum @ fDATA = 160 MSPS with fOUT = fDATA/3 02858-015 100 02858-012 50 0 Figure 15. Third-Order IMD Products vs. fOUT @ fDATA = 65 MSPS 90 90 –6dBFS 0dBFS –6dBFS 85 85 80 80 75 75 IMD (dBc) 70 –12dBFS 70 –3dBFS 65 65 60 60 55 55 50 0 10 20 30 40 50 FREQUENCY (MHz) 02858-013 50 0 5 10 15 20 25 30 FREQUENCY (MHz) Figure 13. In-Band SFDR vs. fOUT @ fDATA = 160 MSPS 02858-016 SFDR (dBc) 0dBFS Figure 16. Third-Order IMD Products vs. fOUT @ fDATA = 78 MSPS 90 90 85 85 80 80 –6dBFS IMD (dBc) 0dBFS 70 65 75 –3dBFS 70 0dBFS 65 60 60 –12dBFS 55 55 50 10 20 30 40 50 FREQUENCY (MHz) Figure 14. Out-of-Band SFDR vs. fOUT @ fDATA = 160 MSPS 0 10 20 30 40 50 60 FREQUENCY (MHz) Figure 17. Third-Order IMD Products vs. fOUT @ fDATA = 160 MSPS Rev. E | Page 13 of 56 02858-017 50 0 02858-014 SFDR (dBc) –6dBFS 75 AD9775 90 90 –3dBFS 85 85 80 80 4× 70 2× 1× 65 55 55 50 3.1 20 30 40 50 60 FREQUENCY (MHz) 02858-018 50 3.2 3.3 3.4 3.5 AVDD (V) Figure 18. Third-Order IMD Products vs. fOUT and Interpolation Rate, 1× fDATA = 160 MSPS, 2× fDATA = 160 MSPS, 4× fDATA = 80 MSPS, 8× fDATA = 50 MSPS Figure 21. Third-Order IMD Products vs. AVDD @ fOUT = 10 MHz, fDAC = 320 MSPS, fDATA = 160 MSPS 90 90 4× 8× 85 85 80 80 1× 70 75 PLL OFF 70 65 65 60 60 55 55 50 –15 –10 –5 0 AOUT (dBFS) PLL ON 50 0 50 100 150 INPUT DATA RATE (MSPS) Figure 19. Third-Order IMD Products vs. AOUT and Interpolation Rate, fDATA = 50 MSPS for All Cases, 1× fDAC = 50 MSPS, 2× fDAC = 100 MSPS, 4× fDAC = 200 MSPS, 8× fDAC = 400 MSPS 02858-022 2× SNR (dB) 75 02858-019 IMD (dBc) 65 60 10 –6dBFS 70 60 0 0dBFS 75 02858-021 75 SFDR (dBc) IMD (dBc) 8× Figure 22. SNR vs. Data Rate for fOUT = 5 MHz 90 90 78MSPS 85 80 80 75 75 70 –12dBFS –6dBFS 65 fDATA = 65MSPS 65 60 60 55 55 50 3.1 3.2 3.3 AVDD (V) 3.4 3.5 Figure 20. SFDR vs. AVDD @ fOUT = 10 MHz, fDAC = 320 MSPS, fDATA = 160 MSPS Rev. E | Page 14 of 56 160MSPS 70 50 –50 0 50 TEMPERATURE (°C) Figure 23. SFDR vs. Temperature @ fOUT = fDATA/11 100 02858-023 SFDR (dBc) 85 02858-020 SFDR (dBc) 0dBFS 0 0 –10 –10 –20 –20 –30 –30 AMPLITUDE (dBm) –40 –50 –60 –70 –40 –50 –60 –70 –80 –80 –90 –100 0 50 100 150 FREQUENCY (MHz) 02858-024 –90 –100 0 5 10 15 20 25 30 35 40 45 50 FREQUENCY (MHz) 02858-027 AMPLITUDE (dBm) AD9775 Figure 27. Two-Tone IMD Performance, fDATA = 150 MSPS, Interpolation = 4× Figure 24. Single-Tone Spurious Performance, fOUT = 10 MHz, fDATA = 150 MSPS, No Interpolation 0 0 –10 –20 –30 AMPLITUDE (dBm) AMPLITUDE (dBm) –20 –40 –60 –40 –50 –60 –70 –80 –80 –90 10 20 30 40 50 FREQUENCY (MHz) 0 02858-025 0 –10 –20 –20 –30 –30 AMPLITUDE (dBm) –10 200 250 300 –40 –50 –60 –70 –70 –80 –80 –90 –90 0 50 100 150 200 250 300 FREQUENCY (MHz) 0 5 10 15 20 FREQUENCY (MHz) Figure 29. Two-Tone IMD Performance, fOUT = 10 MHz, fDATA = 50 MSPS, Interpolation = 8× Figure 26. Single-Tone Spurious Performance, fOUT = 10 MHz, fDATA = 150 MSPS, Interpolation = 2× Rev. E | Page 15 of 56 25 02858-029 –100 –100 02858-026 AMPLITUDE (dBm) 0 –60 150 Figure 28. Single-Tone Spurious Performance, fOUT = 10 MHz, fDATA = 80 MSPS, Interpolation = 4× 0 –50 100 FREQUENCY (MHz) Figure 25. Two-Tone IMD Performance, fDATA = 150 MSPS, No Interpolation –40 50 02858-028 –100 –100 AD9775 0 0 –10 –20 AMPLITUDE (dBm) –30 –40 –50 –60 –70 –80 –40 –60 –80 –100 –90 0 100 200 300 400 FREQUENCY (MHz) 0 20 40 60 80 FREQUENCY (MHz) Figure 31. Eight-Tone IMD Performance, fDATA = 160 MSPS, Interpolation = 8× Figure 30. Single-Tone Spurious Performance, fOUT = 10 MHz, fDATA = 50 MSPS, Interpolation = 8× Rev. E | Page 16 of 56 02858-031 –120 –100 02858-030 AMPLITUDE (dBm) –20 AD9775 TERMINOLOGY Adjacent Channel Power Ratio (ACPR) A ratio in dBc between the measured power within a channel relative to its adjacent channel. Monotonicity A DAC is monotonic if the output either increases or remains constant as the digital input increases. Complex Image Rejection In a traditional two-part upconversion, two images are created around the second IF frequency. These images are redundant and have the effect of wasting transmitter power and system bandwidth. By placing the real part of a second complex modulator in series with the first complex modulator, either the upper or lower frequency image near the second IF can be rejected. Offset Error The deviation of the output current from the ideal of 0 is called offset error. For IOUTA, 0 mA output is expected when the inputs are all 0. For IOUTB, 0 mA output is expected when all inputs are set to 1. Complex Modulation The process of passing the real and imaginary components of a signal through a complex modulator (transfer function = ejωt = cosωt + jsinωt) and realizing real and imaginary components on the modulator output. Differential Nonlinearity (DNL) DNL is the measure of the variation in analog value, normalized to full scale, associated with a 1 LSB change in digital input code. Gain Error The difference between the actual and ideal output span. The actual span is determined by the output when all inputs are set to 1 minus the output when all inputs are set to 0. Output Compliance Range The range of allowable voltage at the output of a current output DAC. Operation beyond the maximum compliance limits may cause either output stage saturation or breakdown, resulting in nonlinear performance. Pass Band Frequency band in which any input applied therein passes unattenuated to the DAC output. Power Supply Rejection The maximum change in the full-scale output as the supplies are varied from minimum to maximum specified voltages. Settling Time The time required for the output to reach and remain within a specified error band about its final value, measured from the start of the output transition. Glitch Impulse Asymmetrical switching times in a DAC give rise to undesired output transients that are quantified by a glitch impulse. It is specified as the net area of the glitch in pV-s. Signal-to-Noise Ratio (SNR) SNR is the ratio of the rms value of the measured output signal to the rms sum of all other spectral components below the Nyquist frequency, excluding the first six harmonics and dc. The value for SNR is expressed in decibels. Group Delay Number of input clocks between an impulse applied at the device input and the peak DAC output current. A half-band FIR filter has constant group delay over its entire frequency range. Spurious-Free Dynamic Range The difference, in dB, between the rms amplitude of the output signal and the peak spurious signal over the specified bandwidth. Impulse Response Response of the device to an impulse applied to the input. Stop-Band Rejection The amount of attenuation of a frequency outside the pass band applied to the DAC, relative to a full-scale signal applied at the DAC input within the pass band. Interpolation Filter If the digital inputs to the DAC are sampled at a multiple rate of fDATA (interpolation rate), a digital filter can be constructed with a sharp transition band near fDATA/2. Images that would typically appear around fDAC (output data rate) can be greatly suppressed. Linearity Error (Also called integral nonlinearity or INL.) It is defined as the maximum deviation of the actual analog output from the ideal output, determined by a straight line drawn from zero scale to full scale. Temperature Drift Temperature drift is specified as the maximum change from the ambient (25°C) value to the value at either TMIN or TMAX. For offset and gain drift, the drift is reported in ppm of full-scale range (FSR) per °C. For reference drift, the drift is reported in ppm per °C. Total Harmonic Distortion (THD) THD is the ratio of the rms sum of the first six harmonic components to the rms value of the measured fundamental. It is expressed as a percentage or in decibels (dB). Rev. E | Page 17 of 56 AD9775 MODE CONTROL (VIA SPI PORT) Table 10. Mode Control via SPI Port1 Address 0x00 Bit 7 SDIO Bidirectional 0 = Input 1 = I/O Bit 6 LSB, MSB First, 0 = MSB 1 = LSB Bit 5 Software Reset on Logic 1 Bit 4 Sleep Mode Logic 1 Shuts Down the DAC Output Currents Bit 3 Power-Down Mode Logic 1 Shuts Down All Digital and Analog Functions 0x 01 Filter Interpolation Rate (1×, 2×, 4×, 8×) Filter Interpolation Rate (1×, 2×, 4×, 8×) Modulation Mode (None, fS/2, fS/4, fS/8) Modulation Mode (None, fS/2, fS/4, fS/8) 0 = No Zero Stuffing on Interpolation Filters, Logic 1 Enables Zero Stuffing. 0x 02 0 = Signed Input Data 1 = Unsigned 0 = Two-Port Mode 1 = One-Port Mode DATACLK Driver Strength DATACLK Invert 0 = No Invert 1 = Invert 0x 03 Data Rate Clock Output2 0x 04 0 = PLL OFF2 1 = PLL ON 0x 05 0x 06 0x 07 0x 08 0x 0C 2 Bit 0 0 = e−jωt 1 = e+jωt DATACLK/ PLL_LOCK2 Select 0 = PLLLOCK 1 = DATACLK ONEPORTCLK Invert 0 = No Invert 1 = Invert IQSEL Invert 0 = No Invert 1 = Invert Q First 0 = I First 1 = Q First PLL Divide (Prescaler) Ratio PLL Charge Pump Control PLL Divide (Prescaler) Ratio PLL Charge Pump Control IDAC Fine Gain Adjustment IDAC Offset Adjustment Bit 9 IDAC IOFFSET Direction 0 = IOFFSET on IOUTA 1 = IOFFSET on IOUTB IDAC Offset Adjustment Bit 8 IDAC Offset Adjustment Bit 7 IDAC Offset Adjustment Bit 6 IDAC Offset Adjustment Bit 5 IDAC Coarse Gain Adjustment IDAC Offset IDAC Offset Adjustment Adjustment Bit 4 Bit 3 IDAC Offset Adjustment Bit 1 IDAC Offset Adjustment Bit 2 IDAC Offset Adjustment Bit 0 QDAC Fine Gain Adjustment QDAC Coarse Gain Adjustment QDAC Offset Adjustment Bit 9 QDAC IOFFSET Direction 0 = IOFFSET on IOUTA 1 = IOFFSET on IOUTB QDAC Offset Adjustment Bit 8 QDAC Offset Adjustment Bit 7 QDAC Offset Adjustment Bit 6 QDAC Offset Adjustment Bit 5 0x 0D 1 Bit 1 PLL_LOCK Indicator PLL Charge Pump Control 0 = Automatic Charge Pump Control, 1 = Programmable 0x 09 0x 0A 0x 0B Bit 2 1R/2R Mode DAC Output Current Set by One or Two External Resistors 0 = 2R, 1 = 1R 1 = Real Mix Mode 0 = Complex Mix Mode QDAC Offset Adjustment Bit 4 QDAC Offset Adjustment Bit 3 QDAC Offset Adjustment Bit 1 Version Register Default values are shown in bold. See the Two-Port Data Input Mode section. Rev. E | Page 18 of 56 QDAC Offset Adjustment Bit 2 QDAC Offset Adjustment Bit 0 AD9775 REGISTER DESCRIPTIONS ADDRESS 0x00 Bit 3: Logic 1 enables zero-stuffing mode for interpolation filters. Bit 7: Logic 0 (default) causes the SPI_SDIO pin to act as an input during the data transfer (Phase 2) of the communications cycle. When set to 1, SPI_SDIO can act as an input or output, depending on Bit 7 of the instruction byte. Bit 2: Default (1) enables the real mix mode. The I and Q data channels are individually modulated by fS/2, fS/4, or fS/8 after the interpolation filters. However, no complex modulation is done. In the complex mix mode (Logic 0), the digital modulators on the I and Q data channels are coupled to create a digital complex modulator. When the AD9775 is applied in conjunction with an external quadrature modulator, rejection can be achieved of either the higher or lower frequency image around the second IF frequency (that is, the LO of the analog quadrature modulator external to the AD9775) according to the bit value of Register 0x01, Bit 1. Bit 6: Logic 0 (default) determines the direction (LSB/MSB first) of the communications and data transfer communications cycles. Refer to the MSB/LSB Transfers section for more details. Bit 5: Writing 1 to this bit resets the registers to their default values and restarts the chip. The RESET bit always reads back 0. Register Address 0x00 bits are not cleared by this software reset. However, a high level at the RESET pin forces all registers, including those in Address 0x00, to their default state. Bit 4: Sleep Mode. A Logic 1 to this bit shuts down the DAC output currents. Bit 3: Power Down. Logic 1 shuts down all analog and digital functions except for the SPI port. Bit 2: 1R/2R Mode. The default (0) places the AD9775 in tworesistor mode. In this mode, the IREF currents for the I and Q DAC references are set separately by the RSET resistors on FSADJ1 and FSADJ2 (Pin 60 and Pin 59). In 2R mode, assuming the coarse gain setting is full scale and the fine gain setting is zero, IFULLSCALE1 = 32 × VREF/FSADJ1 and IFULLSCALE2 = 32 × VREF/FSADJ2. With this bit set to 1, the reference currents for both I and Q DACs are controlled by a single resistor on Pin 60. IFULLSCALE in one-resistor mode for both of the I and Q DACs is half of what it would be in 2R mode, assuming all other conditions (RSET, register settings) remain unchanged. The full-scale current of each DAC can still be set to 20 mA by choosing a resistor of half the value of the RSET value used in 2R mode. Bit 1: PLL_LOCK Indicator. When the PLL is enabled, reading this bit gives the status of the PLL. A Logic 1 indicates the PLL is locked. A Logic 0 indicates an unlocked state. Bit 1: Logic 0 (default) causes the complex modulation to be of the form e− jωt, resulting in the rejection of the higher frequency image when the AD9775 is used with an external quadrature modulator. A Logic 1 causes the modulation to be of the form e+jωt, which causes rejection of the lower frequency image. Bit 0: In two-port mode, a Logic 0 (default) causes Pin 8 to act as a lock indicator for the internal PLL. A Logic 1 in this register causes Pin 8 to act as a DATACLK. For more information, see the Two-Port Data Input Mode section. ADDRESS 0x02 Bit 7: Logic 0 (default) causes data to be accepted on the inputs as twos complement binary. Logic 1 causes data to be accepted as straight binary. Bit 6: Logic 0 (default) places the AD9775 in two-port mode. I and Q data enters the AD9775 via Ports 1 and 2, respectively. A Logic 1 places the AD9775 in one-port mode in which interleaved I and Q data is applied to Port 1. See Table 9 for detailed information on how to use the DATACLK/PLL_LOCK, IQSEL, and ONEPORTCLK modes. Bit 7 and Bit 6: This is the filter interpolation rate according to the following table. Bit 5: DATACLK Driver Strength. With the internal PLL disabled and this bit set to Logic 0, it is recommended that DATACLK be buffered. When this bit is set to Logic 1, DATACLK acts as a stronger driver capable of driving small capacitive loads. Table 11. Bit 4: Logic 0 (default). A value of 1 inverts DATACLK at Pin 8. ADDRESS 0x01 00 01 10 11 Bit 2: Logic 0 (default). A value of 1 inverts ONEPORTCLK at Pin 32. 1× 2× 4× 8× Bit 5 and Bit 4: This is the modulation mode according to the following table. Table 12. 00 01 10 11 Bit 1: Logic 0 (default) causes IQSEL = 0 to direct input data to the I channel, while IQSEL = 1 directs input data to the Q channel. Bit 0: Logic 0 (default) defines IQ pairing as IQ, IQ… while programming a Logic 1 causes the pair ordering to be QI, QI… None fS/2 fS/4 fS/8 Rev. E | Page 19 of 56 AD9775 ADDRESS 0x03 ADDRESS 0x05, ADDRESS 0x09 Bit 7: Allows the data rate clock (divided down from the DAC clock) to be output at either the DATACLK/PLL_LOCK pin (Pin 8) or at the SPI_SDO pin (Pin 53). The default of 0 in this register enables the data rate clock at DATACLK/ PLL_LOCK, while a 1 in this register causes the data rate clock to be output at SPI_SDO. For more information, see the Two-Port Data Input Mode section. Bit 7 to Bit 0: These bits represent an 8-bit binary number (Bit 7 MSB) that defines the fine gain adjustment of the I (0x05) and Q (0x09) DAC, according to Equation 1. Bit 1 and Bit 0: Setting this divide ratio to a higher number allows the VCO in the PLL to run at a high rate (for best performance) while the DAC input and output clocks run substantially slower. The divider ratio is set according to the following table. Bit 3 to Bit 0: These bits represent a 4-bit binary number (Bit 3 MSB) that defines the coarse gain adjustment of the I (0x06) and Q (0x0A) DACs, according to Equation 1. ADDRESS 0x07, ADDRESS 0x0B Bit 7 to Bit 0: These bits are used in conjunction with Address 0x08, 0x0C, Bit 1 and Bit 0. ADDRESS 0x08, ADDRESS 0x0C Table 13. 00 01 10 11 ADDRESS 0x06, ADDRESS 0x0A Bit 1 and Bit 0: The 10 bits from these two address pairs (0x07, 0x08 and 0x0B, 0x0C) represent a 10-bit binary number that defines the offset adjustment of the I and Q DACs, according to Equation 1 (0x07, 0x0B—Bit 7 MSB/0x08, 0x0C— Bit 0 LSB). ÷1 ÷2 ÷4 ÷8 ADDRESS 0x04 ADDRESS 0x08, ADDRESS 0x0C Bit 7: Logic 0 (default) disables the internal PLL. Logic 1 enables the PLL. Bit 7: This bit determines the direction of the offset of the I (0x08) and Q (0x0C) DACs. A Logic 0 applies a positive offset current to IOUTA, while a Logic 1 applies a positive offset current to IOUTB. The magnitude of the offset current is defined by the bits in Addresses 0x07, 0x0B, 0x08, and 0x0C, according to Equation 1. Bit 6: Logic 0 (default) sets the charge pump control to automatic. In this mode, the charge pump bias current is controlled by the divider ratio defined in Address 0x03, Bits 1 and 0. Logic 1 allows the user to manually define the charge pump bias current using Address 0x04, Bits 2, 1, and 0. Adjusting the charge pump bias current allows the user to optimize the noise/settling performance of the PLL. Bit 2 to Bit 0: With the charge pump control set to manual, these bits define the charge pump bias current according to the following table. Equation 1 shows IOUTA and IOUTB as a function of fine gain, coarse gain, and offset adjustment when using the 2R mode. In 1R mode, the current IREF is created by a single FSADJ resistor (Pin 60). This current is divided equally into each channel so that a scaling factor of one-half must be added to these equations for full-scale currents for both DACs and the offset. Table 14. 000 001 010 011 111 50 μA 100 μA 200 μA 400 μA 800 μA ⎡⎛ 6 × I REF I OUTA = ⎢⎜⎜ 8 ⎣⎢⎝ ⎞⎛ COARSE + 1 ⎞ ⎛ 3 × I REF ⎟⎟ − ⎜⎜ ⎟⎟⎜⎜ 16 ⎠⎝ ⎠ ⎝ 32 ⎡⎛ 6 × I REF I OUTB = ⎢⎜⎜ 8 ⎣⎢⎝ ⎞⎛ COARSE + 1 ⎞ ⎛ 3 × I REF ⎟⎟ − ⎜⎜ ⎟⎟⎜⎜ 16 ⎠⎝ ⎠ ⎝ 32 ⎞⎛ FINE ⎞⎤ ⎡⎛ 1024 ⎞⎛ DATA ⎞ ⎤ ⎟⎟⎜ ⎟⎥ × ⎢⎜ ⎟⎜ 14 ⎟ ⎥ (A) ⎠⎦ ⎠⎝ 256 ⎠⎦⎥ ⎣⎝ 24 ⎠⎝ 2 14 ⎞⎛ FINE ⎞ ⎤ ⎡⎛ 1024 ⎞⎛⎜ 2 − DATA − 1 ⎞⎟⎤ ⎥ (A) ⎟⎟⎜ ⎟ ⎥ × ⎢⎜ ⎟ ⎟⎥ 2 14 ⎠⎝ 256 ⎠ ⎦⎥ ⎢⎣⎝ 24 ⎠⎜⎝ ⎠⎦ ⎛ OFFSET ⎞ I OFFSET = 4 × I REF ⎜ ⎟ (A) ⎝ 1024 ⎠ Rev. E | Page 20 of 56 (1) AD9775 FUNCTIONAL DESCRIPTION The AD9775 dual interpolating DAC consists of two data channels that can be operated independently or coupled to form a complex modulator in an image reject transmit architecture. Each channel includes three FIR filters, making the AD9775 capable of 2×, 4×, or 8× interpolation. High speed input and output data rates can be achieved within the following limitations. SDO (PIN 53) SPI_CLK (PIN 55) CSB (PIN 56) Figure 32. SPI Port Interface Table 15. Interpolation Rate (MSPS) 1× 2× 4× 8× AD9775 SPI PORT INTERFACE 02858-032 SDIO (PIN 54) Input Data Rate (MSPS) 160 160 100 50 DAC Sample Rate (MSPS) 160 320 400 400 Both data channels contain a digital modulator capable of mixing the data stream with an LO of fDAC/2, fDAC/4, or fDAC/8, where fDAC is the output data rate of the DAC. A zero-stuffing feature is also included and can be used to improve pass-band flatness for signals being attenuated by the sin(x)/x characteristic of the DAC output. The speed of the AD9775, combined with the digital modulation capability, enables direct IF conversion architectures at 70 MHz and higher. The digital modulators on the AD9775 can be coupled to form a complex modulator. By using this feature with an external analog quadrature modulator, such as the Analog Devices AD8345, an image rejection architecture can be enabled. To optimize the image rejection capability, as well as LO feedthrough in this architecture, the AD9775 offers programmable (via the SPI port) gain and offset adjust for each DAC. Also included on the AD9775 are a phase-locked loop (PLL) clock multiplier and a 1.20 V band gap voltage reference. With the PLL enabled, a clock applied to the CLK+/CLK− inputs is frequency multiplied internally and generates all necessary internal synchronization clocks. Each 14-bit DAC provides two complementary current outputs whose full-scale currents can be determined either from a single external resistor or independently from two separate resistors (see the 1R/2R Mode section). The AD9775 features a low jitter, differential clock input that provides excellent noise rejection while accepting a sine or square wave input. Separate voltage supply inputs are provided for each functional block to ensure optimum noise and distortion performance. Sleep and power-down modes can be used to turn off the DAC output current (sleep) or the entire digital and analog sections (power-down) of the chip. An SPI-compliant serial port is used to program the many features of the AD9775. Note that in power-down mode, the SPI port is the only section of the chip still active. SERIAL INTERFACE FOR REGISTER CONTROL The AD9775 serial port is a flexible, synchronous serial communications port that allows easy interface to many industry-standard microcontrollers and microprocessors. The serial I/O is compatible with most synchronous transfer formats, including both the Motorola SPI and Intel SSR protocols. The interface allows read/write access to all registers that configure the AD9775. Single- or multiple-byte transfers are supported, as well as MSB-first or LSB-first transfer formats. The AD9775 serial interface port can be configured as a single pin I/O (SDIO) or two unidirectional pins for I/O (SDIO/SDO). GENERAL OPERATION OF THE SERIAL INTERFACE There are two phases to a communication cycle with the AD9775. Phase 1 is the instruction cycle, which is the writing of an instruction byte into the AD9775 coincident with the first eight SCLK rising edges. The instruction byte provides the AD9775 serial port controller with information regarding the data transfer cycle, which is Phase 2 of the communication cycle. The Phase 1 instruction byte defines whether the upcoming data transfer is read or write, the number of bytes in the data transfer, and the starting register address for the first byte of the data transfer. The first eight SCLK rising edges of each communication cycle are used to write the instruction byte into the AD9775. A Logic 1 on the SPI_CSB pin, followed by a logic low, resets the SPI port timing to the initial state of the instruction cycle. This is true regardless of the present state of the internal registers or the other signal levels present at the inputs to the SPI port. If the SPI port is in the middle of an instruction cycle or a data transfer cycle, none of the present data is written. The remaining SCLK edges are for Phase 2 of the communication cycle. Phase 2 is the actual data transfer between the AD9775 and the system controller. Phase 2 of the communication cycle is a transfer of one to four data bytes as determined by the instruction byte. Typically, using one multibyte transfer is the preferred method. However, single byte data transfers are useful to reduce CPU overhead when register access requires one byte only. Registers change immediately upon writing to the last bit of each transfer byte. Rev. E | Page 21 of 56 AD9775 SPI_SDO (Pin 53)—Serial Data Out Data is read from this pin for protocols that use separate lines for transmitting and receiving data. In the case where the AD9775 operates in a single bidirectional I/O mode, this pin does not output data and is set to a high impedance state. INSTRUCTION BYTE The instruction byte contains the information shown next Table 16. N1 0 0 1 1 N0 0 1 0 1 Description Transfer 1 Byte Transfer 2 Bytes Transfer 3 Bytes Transfer 4 Bytes MSB/LSB TRANSFERS The AD9775 serial port can support both most significant bit (MSB) first or least significant bit (LSB) first data formats. This functionality is controlled by the LSB-first bit in Register 0. The default is MSB first. R/W Bit 7 of the instruction byte determines whether a read or a write data transfer occurs after the instruction byte write. Logic 1 indicates read operation. Logic 0 indicates a write operation. When this bit is set active high, the AD9775 serial port is in LSB-first format. In LSB-first mode, the instruction byte and data bytes must be written from LSB to MSB. In LSB-first mode, the serial port internal byte address generator increments for each byte of the multibyte communication cycle. N1, N0 Bit 6 and Bit 5 of the instruction byte determine the number of bytes to be transferred during the data transfer cycle. The bit decodes are shown next. Table 17. MSB I7 I6 I5 I4 I3 I2 I1 LSB I0 R/W N1 N0 A4 A3 A2 A1 A0 A4, A3, A2, A1, A0 Bit 4 to Bit 0 of the instruction byte determine which register is accessed during the data transfer portion of the communications cycle. For multibyte transfers, this address is the starting byte address. The remaining register addresses are generated by the AD9775. SERIAL INTERFACE PORT PIN DESCRIPTIONS SPI_CLK (Pin 55)—Serial Clock The serial clock pin is used to synchronize data to and from the AD9775 and to run the internal state machines. SPI_CLK maximum frequency is 15 MHz. All data input to the AD9775 is registered on the rising edge of SPI_CLK. All data is driven out of the AD9775 on the falling edge of SPI_CLK. SPI_CSB (Pin 56)—Chip Select Active low input starts and gates a communication cycle. It allows more than one device to be used on the same serial communications lines. The SDO and SDIO pins go to a high impedance state when this input is high. Chip select should stay low during the entire communication cycle. SPI_SDIO (Pin 54)—Serial Data I/O Data is always written into the AD9775 on this pin. However, this pin can be used as a bidirectional data line. The configuration of this pin is controlled by Bit 7 of Register Address 0x00. The default is Logic 0, which configures the SDIO pin as unidirectional. When this bit is set default low, the AD9775 serial port is in MSB-first format. In MSB-first mode, the instruction byte and data bytes must be written from MSB to LSB. In MSB-first mode, the serial port internal byte address generator decrements for each byte of the multibyte communication cycle. When incrementing from 0x1F, the address generator changes to 0x00. When decrementing from 0x00, the address generator changes to 0x1F. NOTES ON SERIAL PORT OPERATION The AD9775 serial port configuration bits reside in Bit 6 and Bit 7 of Register Address 0x00. It is important to note that the configuration changes immediately upon writing to the last bit of the register. For multibyte transfers, writing to this register may occur during the middle of the communication cycle. Care must be taken to compensate for this new configuration for the remaining bytes of the current communication cycle. The same considerations apply to setting the reset bit in Register Address 0x00. All other registers are set to their default values, but the software reset does not affect the bits in Register Address 0x00. It is recommended to use only single-byte transfers when changing serial port configurations or initiating a software reset. A write to Bit 1, Bit 2, and Bit 3 of Address 0x00 with the same logic levels as for Bit 7, Bit 6, and Bit 5 (bit pattern is XY1001YX binary) allows the user to reprogram a lost serial port configuration and to reset the registers to their default values. A second write to Address 0x00 with reset bit low and serial port configuration as specified above (XY) reprograms the OSC IN multiplier setting. A changed fSYSCLK frequency is stable after a maximum of 200 fMCLK cycles (equals wake-up time). Rev. E | Page 22 of 56 AD9775 INSTRUCTION CYCLE DATA TRANSFER CYCLE CS SDIO I6(N) R/W I5(N) I4 I3 I2 I1 I0 SDO D7N D6N D20 D10 D00 D7N D6N D20 D10 D00 02858-033 SCLK Figure 33. Serial Register Interface Timing MSB First INSTRUCTION CYCLE DATA TRANSFER CYCLE CS I0 I1 I2 I3 I4 I5(N) I6(N) R/W SDO D00 D10 D20 D6N D7N D00 D10 D20 D6N D7N Figure 34. Serial Register Interface Timing LSB First tSCLK tDS CS tPWH tPWL SCLK SDIO tDH INSTRUCTION BIT 7 T6 INSTRUCTION BIT 02858-035 tDS Figure 35. Timing Diagram for Register Write to AD9775 CS SCLK tDV SDIO DATA BIT N DATA BIT N–1 SDO Figure 36. Timing Diagram for Register Read from AD9775 Rev. E | Page 23 of 56 02858-036 SDIO 02858-034 SCLK AD9775 25 DAC OPERATION COARSE REFERENCE CURRENT (mA) The dual, 14-bit DAC output of the AD9775, along with the reference circuitry, gain, and offset registers, is shown in Figure 37. Note that an external reference can be used by simply overdriving the internal reference with the external reference. Referring to the transfer functions in Equation 1, a reference current is set by the internal 1.2 V reference, the external RSET resistor, and the values in the coarse gain register. The fine gain DAC subtracts a small amount from this and the result is input to IDAC and QDAC, where it is scaled by an amount equal to 1024/24. Figure 38 and Figure 39 show the scaling effect of the coarse and fine adjust DACs. IDAC and QDAC are PMOS current source arrays, segmented in a 5-4-5 configuration. The 5 MSBs control an array of 31 current sources. The next four bits consist of 15 current sources whose values are all equal to 1/16 of an MSB current source. The 5 LSBs are binary weighted fractions of the middle bits’ current sources. All current sources are switched to either IOUTA or IOUTB, depending on the input code. 20 2R MODE 15 10 1R MODE 5 0 5 10 20 15 02858-039 0 COARSE GAIN REGISTER CODE (ASSUMING RSET1, RSET2 = 1.9kΩ) Figure 38. Coarse Gain Effect on IFULLSCALE FINE REFERENCE CURRENT (mA) 0 The fine adjustment of the gain of each channel allows for improved balance of QAM modulated signals, resulting in improved modulation accuracy and image rejection. In the section Interfacing the AD9775 with the AD8345 Quadrature Modulator, the performance data shows to what degree image rejection can be improved when the AD9775 is used with an AD8345 quadrature modulator from Analog Devices, Inc. AVDD –0.5 1R MODE –1.0 2R MODE –1.5 –2.0 –2.5 –3.0 200 400 600 800 FINE GAIN REGISTER CODE (ASSUMING RSET1, RSET2 = 1.9kΩ) REFIO Figure 39. Fine Gain Effect on IFULLSCALE 7kΩ 02858-038 0.7V Figure 37. Equivalent Internal Reference Circuit OFFSET CONTROL OFFSET DAC REGISTERS FINE GAIN DAC GAIN CONTROL REGISTERS FINE GAIN DAC 1.2VREF IDAC IOUTA1 IOUTB1 REFIO COARSE GAIN DAC 0.1μF COARSE GAIN DAC QDAC IOUTA2 IOUTB2 FSADJ2 RSET1 RSET2 OFFSET OFFSET CONTROL DAC GAIN REGISTERS CONTROL REGISTERS Figure 40. DAC Outputs, Reference Current Scaling, and Gain/Offset Adjust Rev. E | Page 24 of 56 02858-037 FSADJ1 1000 02858-040 0 84μA AD9775 –10 OFFSET REGISTER 1 ADJUSTED –20 –30 –40 –50 –60 OFFSET REGISTER 2 ADJUSTED, WITH OFFSET REGISTER 1 SET TO OPTIMIZED VALUE –70 –80 –1024 –768 –512 –256 256 512 768 CLOCK INPUT CONFIGURATIONS The clock inputs to the AD9775 can be driven differentially or single-ended. The internal clock circuitry has supply and ground (CLKVDD, CLKGND) separate from the other supplies on the chip to minimize jitter from internal noise sources. Figure 43 shows the AD9775 driven from a single-ended clock source. The CLK+/CLK− pins form a differential input (CLKIN) so that the statically terminated input must be dcbiased to the midswing voltage level of the clock driven input. AD9775 5 4 RSERIES CLK+ CLKVDD CLK– VTHRESHOLD 0.1μF CLKGND 02858-043 In 2R mode, the reference current for each channel is set independently by the FSADJ resistor on that channel. The AD9775 can be programmed to derive its reference current from a single resistor on Pin 60 by placing the part into 1R mode. The transfer functions in Equation 1 are valid for 2R mode. In 1R mode, the current developed in the single FSADJ resistor is split equally between the two channels. The result is that in 1R mode, a scale factor of 1/2 must be applied to the formulas in Equation 1. The full-scale DAC current in 1R mode can still be set to as high as 20 mA by using the internal 1.2 V reference and a 950 Ω resistor instead of the 1.9 kΩ resistor typically used in the 2R mode. Figure 43. Single-Ended Clock Driving Clock Inputs A configuration for differentially driving the clock inputs is given in Figure 44. DC-blocking capacitors can be used to couple a clock driver output whose voltage swings exceed CLKVDD or CLKGND. If the driver voltage swings are within the supply range of the AD9775, the dc-blocking capacitors and bias resistors are not necessary. AD9775 3 0.1μF 1kΩ CLK+ 2R MODE 1kΩ 2 ECL/PECL 0.1μF 0.1μF 1R MODE CLKVDD 1kΩ CLK– 1 CLKGND 200 400 600 800 COARSE GAIN REGISTER CODE (ASSUMING RSET1, RSET2 = 1.9kΩ) 1000 02858-041 0 Figure 41. DAC Output Offset Current Rev. E | Page 25 of 56 02858-044 1kΩ 0 1024 Figure 42. Offset Adjust Control, Effect on LO Suppression 1R/2R MODE OFFSET CURRENT (mA) 0 DAC1, DAC2 (OFFSET REGISTER CODES) 02858-042 In Figure 42, the negative scale represents an offset added to IOUTB, while the positive scale represents an offset added to IOUTA of the respective DAC. Offset Register 1 corresponds to IDAC, while Offset Register 2 corresponds to QDAC. Figure 42 represents the AD9775 synthesizing a complex signal that is then dc-coupled to an AD8345 quadrature modulator with an LO of 800 MHz. The dc coupling allows the input offset of the AD8345 to be calibrated out as well. The LO suppression at the AD8345 output was optimized first by adjusting Offset Register 1 in the AD9775. When an optimal point was found (roughly Code 54), this code was held in Offset Register 1, and Offset Register 2 was adjusted. The resulting LO suppression is 70 dBFS. These are typical numbers; the specific code for optimization varies from part to part. 0 LO SUPPRESSION (dBFS) The offset control defines a small current that can be added to IOUTA or IOUTB (not both) on the IDAC and QDAC. The selection of which IOUT this offset current is directed toward is programmable via Register 0x08, Bit 7 (IDAC) and Register 0x0C, Bit 7 (QDAC). Figure 41 shows the scale of the offset current that can be added to one of the complementary outputs on the IDAC and QDAC. Offset control can be used for suppression of LO leakage resulting from modulation of dc signal components. If the AD9775 is dccoupled to an external modulator, this feature can be used to cancel the output offset on the AD9775 as well as the input offset on the modulator. Figure 42 shows a typical example of the effect that the offset control has on LO suppression. Figure 44. Differential Clock Driving Clock Inputs AD9775 A transformer, such as the T1-1T from Mini-Circuits®, can also be used to convert a single-ended clock to differential. This method is used on the AD9775 evaluation board so that an external sine wave with no dc offset can be used as a differential clock. INTERPOLATION FILTERS, MODULATORS, AND DACS 2 The charge pump, VCO, differential clock input buffer, phase detector, prescaler, and clock distribution are all powered from CLKVDD. PLL lock status is indicated by the logic signal at the DATACLK_PLL_LOCK pin, as well as by the status of Bit 1, Register 0x00. To ensure optimum phase noise performance from the PLL clock multiplier and distribution, CLKVDD should originate from a clean analog supply. Table 18 defines the minimum input data rates vs. the interpolation and PLL divider setting. If the input data rate drops below the defined minimum under these conditions, VCO noise may increase significantly. The VCO speed is a function of the input data rate, the interpolation rate, and the VCO prescaler, according to the following function: PRESCALER VCO LPF PLL DIVIDER (PRESCALER) CONTROL INTERNAL SPI CONTROL REGISTERS INTERPOLATION RATE CONTROL MODULATION RATE CONTROL SPI PORT PLL CONTROL (PLL ON) Figure 45. PLL and Clock Circuitry with PLL Enabled CLK+ CLK– PLL_LOCK 1 = LOCK 0 = NO LOCK AD9775 INTERPOLATION FILTERS, MODULATORS, AND DACS 2 The PLL clock multiplier and distribution circuitry produce the necessary internal synchronized 1×, 2×, 4×, and 8× clocks for the rising edge triggered latches, interpolation filters, modulators, and DACs. This circuitry consists of a phase detector, charge pump, voltage controlled oscillator (VCO), prescaler, clock distribution, and SPI port control. CHARGE PUMP 8 CLOCK DISTRIBUTION CIRCUITRY INPUT DATA LATCHES PROGRAMMABLE PLL VCO Speed (MHz) = Input Data Rate (MHz) × Interpolation Rate × Prescaler 4 PHASE DETECTOR 1 The quality of the clock and data input signals is important in achieving optimum performance. The external clock driver circuitry should provide the AD9775 with a low jitter clock input that meets the minimum/maximum logic levels while providing fast edges. Although fast clock edges help minimize any jitter that manifests itself as phase noise on a reconstructed waveform, the high gain bandwidth product of the AD9775 clock input comparator can tolerate differential sine wave inputs as low as 0.5 V p-p with minimal degradation of the output noise floor. CLKIN can function either as an input data rate clock (PLL enabled) or as a DAC data rate clock (PLL disabled) according to the state of Address 0x02, Bit 7 in the SPI port register. The internal operation of the AD9775 clock circuitry in these two modes is illustrated in Figure 45 and Figure 46. PLLVDD AD9775 02858-045 Optimum performance of the AD9775 is achieved when the driver is placed very close to the AD9775 clock inputs, thereby negating any transmission line effects such as reflections due to mismatch. CLK– 4 PHASE DETECTOR CHARGE PUMP PRESCALER VCO 8 1 CLOCK DISTRIBUTION CIRCUITRY INPUT DATA LATCHES INTERPOLATION RATE CONTROL PLL DIVIDER (PRESCALER) CONTROL INTERNAL SPI CONTROL REGISTERS SPI PORT MODULATION RATE CONTROL PLL CONTROL (PLL ON) 02858-046 PECL/ECL drivers require varying termination networks, the details of which are left out of Figure 43 and Figure 44 but can be found in application notes such as AND8020/D from ON Semiconductor®. These networks depend on the assumed transmission line impedance and power supply voltage of the clock driver. CLK+ PLL_LOCK 1 = LOCK 0 = NO LOCK Figure 46. PLL and Clock Circuitry with PLL Disabled Table 18. PLL Optimization Interpolation Rate 1 1 1 1 2 2 2 2 4 4 4 4 8 8 8 8 Rev. E | Page 26 of 56 Divider Setting 1 2 4 8 1 2 4 8 1 2 4 8 1 2 4 8 Minimum fDATA 32 16 8 4 24 12 6 3 24 12 6 3 24 12 6 3 Maximum fDATA 160 160 112 56 160 112 56 28 100 56 28 14 50 28 14 7 AD9775 In addition, if the zero-stuffing option is enabled, the VCO doubles its speed again. Phase noise may be slightly higher with the PLL enabled. Figure 47 illustrates typical phase noise performance of the AD9775 with 2× interpolation and various input data rates. The signal synthesized for the phase noise measurement was a single carrier at a frequency of fDATA/4. The repetitive nature of this signal eliminates quantization noise and distortion spurs as a factor in the measurement. Although the curves blend together in Figure 47, the different conditions are given for clarity in Table 19. Figure 47 also contains a table detailing the maximum and minimum fDATA rates for each combination of interpolation rate and PLL divider setting. These rates are guaranteed over the entire supply and operating temperature range. Figure 48 shows typical performance of the PLL lock signal (Pin 8 or Pin 53) when the PLL is in the process of locking. Table 19. Required PLL Prescaler Ratio vs. fDATA fDATA 125 MSPS 125 MSPS 100 MSPS 75 MSPS 50 MSPS PLL Disabled Enabled Enabled Enabled Enabled Prescaler Ratio It is important to note that the resistor/capacitor needed for the PLL loop filter is internal on the AD9775. This suffices unless the input data rate is below 10 MHz, in which case an external series RC is required between the LPF pin and CLKVDD pins. POWER DISSIPATION The AD9775 has three voltage supplies: DVDD, AVDD, and CLKVDD. Figure 49 through Figure 51 show the current required from each of these supplies when each is set to the 3.3 V nominal specified for the AD9775. Power dissipation (PD) can easily be extracted by multiplying the given curves by 3.3. As Figure 49 shows, IDVDD is very dependent on the input data rate, the interpolation rate, and the activation of the internal digital modulator. IDVDD, however, is relatively insensitive to the modulation rate by itself. In Figure 50, IAVDD shows the same type of sensitivity to the data, the interpolation rate, and the modulator function but to a much lesser degree (10 mA into a 330 Ω load while providing a rise time of 3 ns. Figure 53 shows DATACLK driving a 330 Ω resistive load at a frequency of 50 MHz. By enabling the drive strength option (Control Register 0x02, Bit 5), the amplitude of DATACLK under these conditions increases by approximately 200 mV. By programming this bit, the ONEPORTCLK signal shown in Figure 54 can be inverted. With inversion enabled, tOD refers to the delay between the rising edge of the external clock and the falling edge of ONEPORTCLK. The setup and hold times, tS and tH, are with respect to the falling edge of ONEPORTCLK. There is no other effect on timing. tOD 3.0 tOD = 4.0ns (MIN) TO 5.5ns (MAX) CLKIN 2.5 tS = 3.0ns (MIN) tH = –0.5ns (MIN) tIQS = 3.5ns (MIN) tIQH = –1.5ns (MIN) 1.5 ONEPORTCLK 1.0 0.5 I AND Q INTERLEAVED INPUT DATA AT PORT 1 0 DELTA APPROX. 2.8ns –0.5 10 20 30 40 50 TIME (ns) Figure 53. DATACLK Driver Capability into 330 Ω at 50 MHz tS tH IQSEL tIQS tIQH Figure 54. Timing Requirements in One-Port Input Mode with the PLL Enabled Rev. E | Page 29 of 56 02858-054 0 02858-053 AMPLITUDE (V) 2.0 AD9775 tOD ONEPORTCLK DRIVER STRENGTH The drive capability of ONEPORTCLK is identical to that of DATACLK in the two-port mode. Refer to Figure 53 for performance under load conditions. CLKIN IQ PAIRING (Control Register 0x02, Bit 0) DATACLK DATA AT PORTS 1 AND 2 tS Given the following interleaved data stream, where the data indicates the value with respect to full scale: tOD = 6.5ns (MIN) TO 8.0ns (MAX) tS = 5.0ns (MIN) tH = –3.2ns (MIN) tH 02858-055 In one-port mode, the interleaved data is latched into the AD9775 internal I and Q channels in pairs. The order of how the pairs are latched internally is defined by this control register. The following is an example of the effect that this has on incoming interleaved data. Figure 55. Timing Requirements in Two-Port Input Mode with PLL Disabled Table 20. I 0.5 Q 0.5 I 1 Q 1 I 0.5 Q 0.5 I 0 Q 0 I 0.5 tOD Q 0.5 With the control register set to 0 (I first), the data appears at the internal channel inputs in the following order in time: CLKIN Table 21. I Channel Q Channel 0.5 0.5 1 1 0.5 0.5 0 0 0.5 0.5 ONEPORTCLK With the control register set to 1 (Q first), the data appears at the internal channel inputs in the following order in time: Table 22. 0.5 y 1 0.5 0.5 1 0 0.5 0.5 0 x 0.5 I AND Q INTERLEAVED INPUT DATA AT PORT 1 The values x and y represent the next I value and the previous Q value in the series. tS tH IQSEL PLL DISABLED, TWO-PORT MODE tOD = 4.0ns (MIN) With the PLL disabled, a clock at the DAC output rate must be applied to CLKIN. Internal clock dividers in the AD9775 synthesize the DATACLK signal at Pin 8, which runs at the input data rate and can be used to synchronize the input data. Data is latched into input Port 1 and Port 2 of the AD9775 on the rising edge of DATACLK. DATACLK speed is defined as the speed of CLKIN divided by the interpolation rate. With zero stuffing enabled, this division increases by a factor of 2. Figure 55 illustrates the delay between the rising edge of CLKIN and the rising edge of DATACLK, as well as tS and tH in this mode. The programmable modes DATACLK inversion and DATACLK driver strength described in the previous section (PLL Enabled, Two-Port Mode) have identical functionality with the PLL disabled. The data rate clock created by dividing down the DAC clock in this mode can be programmed (via Register 0x03, Bit 7) to be output from the SPI_SDO pin rather than the DATACLK/ PLL_LOCK pin. In some applications, this may improve complex image rejection. When SPI_SDO is used as data rate clock out, tOD increases by 1.6 ns. TO 5.5ns (MAX) tS = 3.0ns (MIN) tH = –1.0ns (MIN) tIQS = 3.5ns (MIN) tIQH = –1.5ns (MIN) tIQS tIQH 02858-056 I Channel Q Channel Figure 56. Timing Requirements in One-Port Input Mode with PLL Disabled PLL DISABLED, ONE-PORT MODE In one-port mode, data is received into the AD9775 as an interleaved stream on Port 1. A clock signal (ONEPORTCLK) running at the interleaved data rate, which is 2× the input data rate of the internal I and Q channels, is available for data synchronization at Pin 32. With PLL disabled, a clock at the DAC output rate must be applied to CLKIN. Internal dividers synthesize the ONEPORTCLK signal at Pin 32. The selection of the data for the I or Q channel is determined by the state of the logic level applied to Pin 31 (IQSEL when the AD9775 is in one-port mode) on the rising edge of ONEPORTCLK. Under these conditions, IQSEL = 0 latches the data into the I channel on the clock rising edge, while IQSEL = 1 latches the data into the Q channel. Rev. E | Page 30 of 56 AD9775 frequency images. This is shown graphically in the frequency domain in Figure 57. e–jωt/2j SINE DC One-port mode is very useful when interfacing with devices such as the Analog Devices AD6622 or AD6623 transmit signal processors, in which two digital data channels have been interleaved (multiplexed). e–jωt/2j e–jωt/2 e–jωt/2 COSINE The programmable modes’ ONEPORTCLK inversion, ONEPORTCLK driver strength, and IQ pairing described in the PLL Enabled, One-Port Mode section have identical functionality with the PLL disabled. DIGITAL FILTER MODES The I and Q datapaths of the AD9775 have their own independent half-band FIR filters. Each datapath consists of three FIR filters, providing up to 8× interpolation for each channel. The rate of interpolation is determined by the state of Control Register 0x01, Bit 7 and Bit 6. Figure 2 to Figure 4 show the response of the digital filters when the AD9775 is set to 2×, 4×, and 8× modes. The frequency axes of these graphs are normalized to the input data rate of the DAC. As the graphs show, the digital filters can provide greater than 75 dB of out-of-band rejection. DC 02858-057 It is possible to invert the I and Q selection by setting control Register 0x02, Bit 1 to the invert state (Logic 1). Figure 56 illustrates the timing requirements for the data inputs as well as the IQSEL input. Note that the 1× interpolation rate is not available in the one-port mode. Figure 57. Real and Imaginary Components of Sinusoidal and Cosinusoidal Waveforms Amplitude modulating a baseband signal with a sine or a cosine convolves the baseband signal with the modulating carrier in the frequency domain. Amplitude scaling of the modulated signal reduces the positive and negative frequency images by a factor of 2. This scaling is very important in the discussion of the various modulation modes. The phase relationship of the modulated signals is dependent on whether the modulating carrier is sinusoidal or cosinusoidal, again with respect to the reference point of the viewer. Examples of sine and cosine modulation are given in Figure 58. Ae–jωt/2j An online tool is available for quick and easy analysis of the AD9775 interpolation filters in the various modes. The link can be accessed at www.analog.com/ad9777image. AMPLITUDE MODULATION SINUSOIDAL MODULATION DC Ae–jωt/2j Rev. E | Page 31 of 56 Ae–jωt/2 Ae–jωt/2 COSINUSOIDAL MODULATION DC Figure 58. Baseband Signal, Amplitude Modulated with Sine and Cosine Carriers 02858-058 Given two sine waves at the same frequency, but with a 90 degree phase difference, a point of view in time can be taken such that the waveform that leads in phase is cosinusoidal and the waveform that lags is sinusoidal. Analysis of complex variables states that the cosine waveform can be defined as having real positive and negative frequency components, while the sine waveform consists of imaginary positive and negative AD9775 MODULATION, NO INTERPOLATION With Control Register 0x01, Bit 7 and Bit 6 set to 00, the interpolation function on the AD9775 is disabled. Figure 59 through Figure 62 show the DAC output spectral characteristics of the AD9775 in the various modulation modes, all with the interpolation filters disabled. The modulation frequency is determined by the state of Control Register 0x01, Bit 5 and Bit 4. The tall rectangles represent the digital domain spectrum of a baseband signal of narrow bandwidth. By comparing the digital domain spectrum to the DAC sin(x)/x roll-off, an estimate can be made for the characteristics required for the DAC reconstruction filter. Note also, per the previous discussion on amplitude modulation, that the spectral components (where modulation is set to fS/4 or fS/8) are scaled by a factor of 2. In the situation where the modulation is fS/2, the modulated spectral components add constructively, and there is no scaling effect. 0 0 –20 –20 AMPLITUDE (dBFS) –40 –60 –40 –60 –80 –80 0.2 0.4 0.6 0.8 1.0 fOUT (×fDATA) 02858-059 0 0 0.4 0.6 0.8 1.0 1.0 fOUT (×fDATA) Figure 59. No Interpolation, Modulation Disabled Figure 61. No Interpolation, Modulation = fDAC/4 0 –20 –20 AMPLITUDE (dBFS) 0 –40 –60 –40 –60 –80 –80 –100 –100 0 0.2 0.4 0.6 0.8 fOUT (×fDATA) 1.0 02858-060 AMPLITUDE (dBFS) 0.2 02858-061 –100 –100 02858-062 AMPLITUDE (dBFS) The Effects of the Digital Modulation on the DAC Output Spectrum, Interpolation Disabled Figure 60. No Interpolation, Modulation = fDAC/2 0 0.2 0.4 0.6 0.8 fOUT (×fDATA) Figure 62. No Interpolation, Modulation = fDAC/8 Rev. E | Page 32 of 56 AD9775 MODULATION, INTERPOLATION = 2× With Control Register 0x01, Bit 7 and Bit 6 set to 01, the interpolation rate of the AD9775 is 2×. Modulation is achieved by multiplying successive samples at the interpolation filter output by the sequence (+1, −1). Figure 63 through Figure 66 represent the spectral response of the AD9775 DAC output with 2× interpolation in the various modulation modes to a narrowband baseband signal (the tall rectangles in the graphic). The advantage of interpolation becomes clear in Figure 63 through Figure 66, where the images that would normally appear in the spectrum around the input data rate frequency are suppressed by >70 dB. Another significant point is that the interpolation filtering is done previous to the digital modulator. For this reason, as Figure 63 through Figure 66 show, the pass band of the interpolation filters can be frequency shifted, giving the equivalent of a high-pass digital filter. Note that when using the fS/4 modulation mode, there is no true stop band as the band edges coincide with each other. In the fS/8 modulation mode, amplitude scaling occurs over only a portion of the digital filter pass band due to constructive addition over just that section of the band. 0 0 –20 –20 AMPLITUDE (dBFS) –40 –60 –40 –60 –80 –80 0.5 1.0 1.5 2.0 fOUT (×fDATA) 0 1.0 1.5 2.0 2.0 fOUT (×fDATA) Figure 63. 2× Interpolation, Modulation = Disabled Figure 65. 2× Interpolation, Modulation = fDAC/4 0 –20 –20 AMPLITUDE (dBFS) 0 –40 –60 –40 –60 –80 –80 –100 0 0.5 1.0 1.5 fOUT (×fDATA) 2.0 02858-064 AMPLITUDE (dBFS) 0.5 02858-065 –100 0 02858-063 –100 02858-066 AMPLITUDE (dBFS) The Effects of the Digital Modulation on the DAC Output Spectrum, Interpolation = 2× –100 Figure 64. 2× Interpolation, Modulation = fDAC/2 0 0.5 1.0 1.5 fOUT (×fDATA) Figure 66. 2× Interpolation, Modulation = fDAC/8 Rev. E | Page 33 of 56 AD9775 MODULATION, INTERPOLATION = 4× With Control Register 0x01, Bit 7 and Bit 6 set to 10, the interpolation rate of the AD9775 is 4×. Modulation is achieved by multiplying successive samples at the interpolation filter output by the sequence (0, +1, 0, −1). Figure 67 through Figure 70 represent the spectral response of the AD9775 DAC output with 4× interpolation in the various modulation modes to a narrow-band baseband signal. 0 0 –20 –20 AMPLITUDE (dBFS) –40 –60 –40 –60 –80 –80 1 2 3 4 fOUT (×fDATA) 0 2 3 4 4 fOUT (×fDATA) Figure 67. 4× Interpolation, Modulation Disabled Figure 69. 4× Interpolation, Modulation = fDAC/2 0 –20 –20 AMPLITUDE (dBFS) 0 –40 –60 –40 –60 –80 –80 –100 –100 0 1 2 3 fOUT (×fDATA) 4 02858-068 AMPLITUDE (dBFS) 1 02858-069 –100 0 02858-067 –100 02858-070 AMPLITUDE (dBFS) The Effects of the Digital Modulation on the DAC Output Spectrum, Interpolation = 4× 0 1 2 3 fOUT (×fDATA) Figure 70. 4× Interpolation, Modulation = fDAC/8 Figure 68. 4× Interpolation, Modulation = fDAC/4 Rev. E | Page 34 of 56 AD9775 MODULATION, INTERPOLATION = 8× With Control Register 0x01, Bit 7 and Bit 6 set to 11, the interpolation rate of the AD9775 is 8×. Modulation is achieved by multiplying successive samples at the interpolation filter output by the sequence (0, +0.707, +1, +0.707, 0, −0.707, −1, +0.707). Figure 71 through Figure 74 represent the spectral response of the AD9775 DAC output with 8× interpolation in the various modulation modes to a narrow-band baseband signal. Looking at Figure 63 through Figure 74, the user can see how higher interpolation rates reduce the complexity of the reconstruction filter needed at the DAC output. It also becomes apparent that the ability to modulate by fS/2, fS/4, or fS/8 adds a degree of flexibility in frequency planning. 0 0 –20 –20 AMPLITUDE (dBFS) –40 –60 –40 –60 –80 –80 –100 2 3 4 fOUT (×fDATA) 0 2 3 4 5 6 7 8 8 fOUT (×fDATA) Figure 73. 8× Interpolation, Modulation = fDAC/4 Figure 71. 8× Interpolation, Modulation Disabled 0 –20 –20 AMPLITUDE (dBFS) 0 –40 –60 –40 –60 –80 –80 –100 –100 0 1 2 3 fOUT (×fDATA) 4 02858-072 AMPLITUDE (dBFS) 1 02858-073 1 02858-071 –100 0 02858-074 AMPLITUDE (dBFS) The Effects of the Digital Modulation on the DAC Output Spectrum, Interpolation = 8× 0 1 2 3 4 5 6 7 fOUT (×fDATA) Figure 74. 8× Interpolation, Modulation = fDAC/8 Figure 72. 8× Interpolation, Modulation = fDAC/2 Rev. E | Page 35 of 56 AD9775 ZERO STUFFING (Control Register 0x01, Bit 3) As shown in Figure 75, a 0 or null in the output frequency response of the DAC (after interpolation, modulation, and DAC reconstruction) occurs at the final DAC sample rate (fDAC). This is due to the inherent sin(x)/x roll-off response in the digital-toanalog conversion. In applications where the desired frequency content is below fDAC/2, this may not be a problem. Note that at fDAC/2 the loss due to sin(x)/x is 4 dB. In direct RF applications, this roll-off may be problematic due to the increased pass-band amplitude variation as well as the reduced amplitude of the desired signal. Consider an application where the digital data into the AD9775 represents a baseband signal around fDAC/4 with a pass band of fDAC/10. The reconstructed signal out of the AD9775 would experience only a 0.75 dB amplitude variation over its pass band. However, the image of the same signal occurring at 3 × fDAC/4 suffers from a pass-band flatness variation of 3.93 dB. This image may be the desired signal in an IF application using one of the various modulation modes in the AD9775. This roll-off of image frequencies can be seen in Figure 59 to Figure 74, where the effect of the interpolation and modulation rate is apparent as well. 10 ZERO STUFFING ENABLED SIN (X)/X ROLL-OFF (dBFS) 0 INTERPOLATING (COMPLEX MIX MODE) (Control Register 0x01, Bit 2) In the complex mix mode, the two digital modulators on the AD9775 are coupled to provide a complex modulation function. In conjunction with an external quadrature modulator, this complex modulation can be used to realize a transmit image rejection architecture. The complex modulation function can be programmed for e+jωt or e−jωt to give upper or lower image rejection. As in the real modulation mode, the modulation frequency ω can be programmed via the SPI port for fDAC/2, fDAC/4, and fDAC/8, where fDAC represents the DAC output rate. OPERATIONS ON COMPLEX SIGNALS Truly complex signals cannot be realized outside of a computer simulation. However, two data channels, both consisting of real data, can be defined as the real and imaginary components of a complex signal. I (real) and Q (imaginary) datapaths are often defined this way. By using the architecture defined in Figure 76, a system can be realized that operates on complex signals, giving a complex (real and imaginary) output. If a complex modulation function (e+jωt) is desired, the real and imaginary components of the system correspond to the real and imaginary components of e+jωt or cosωt and sinωt. As Figure 77 shows, the complex modulation function can be realized by applying these components to the structure of the complex system defined in Figure 76. –10 –20 ZERO STUFFING DISABLED –30 Note that the zero-stuffing option by itself does not change the location of the images but rather their amplitude, pass-band flatness, and relative weighting. For instance, in the previous example, the pass-band amplitude flatness of the image at 3 × fDATA/4 improved to +0.59 dB while the signal level increased slightly from −10.5 dBFS to −8.1 dBFS. –40 a(t) 1.5 2.0 c(t) × b(t) + d × b(t) b(t) IMAGINARY INPUT OUTPUT b(t) × a(t) + c × b(t) Figure 75. Effect of Zero Stuffing on DAC’s sin(x)/x Response To improve upon the pass-band flatness of the desired image, the zero stuffing mode can be enabled by setting the control register bit to Logic 1. This option increases the ratio of fDAC/fDATA by a factor of 2 by doubling the DAC sample rate and inserting a midscale sample (that is, 1000 0000 0000 0000) after every data sample originating from the interpolation filter. This is important as it affects the PLL divider ratio needed to keep the VCO within its optimum speed range. Note that the zero stuffing takes place in the digital signal chain at the output of the digital modulator before the DAC. The net effect is to increase the DAC output sample rate by a factor of 2× with the 0 in the sin(x)/x DAC transfer function occurring at twice the original frequency. A 6 dB loss in amplitude at low frequencies is also evident (see Figure 75). Rev. E | Page 36 of 56 02858-076 1.0 OUTPUT Figure 76. Realization of a Complex System INPUT (REAL) OUTPUT (REAL) INPUT (IMAGINARY) 90° OUTPUT (IMAGINARY) e–jωt = COSωt + jSINωt 02858-077 0.5 02858-075 0 fOUT, NORMALIZED TO fDATA WITH ZERO STUFFING DISABLED (Hz) INPUT COMPLEX FILTER = (c + jd) –50 Figure 77. Implementation of a Complex Modulator AD9775 the baseband real and imaginary channels, now modulated onto orthogonal (cosine and negative sine) carriers at the transmit frequency. It is important to remember that in this application (two baseband data channels) the image rejection is not dependent on the data at either of the AD9775 input channels. In fact, image rejection still occurs with either one or both of the AD9775 input channels active. Note that by changing the sign of the sinusoidal multiplying term in the complex modulator, the upper sideband image could have been suppressed while passing the lower one. This is easily done in the AD9775 by selecting the e+jωt bit (Register 0x01, Bit 1). In purely complex terms, Figure 79 represents the two-stage upconversion from complex baseband to carrier. COMPLEX MODULATION AND IMAGE REJECTION OF BASEBAND SIGNALS In traditional transmit applications, a two-step upconversion is done in which a baseband signal is modulated by one carrier to an intermediate frequency (IF) and then modulated a second time to the transmit frequency. Although this approach has several benefits, a major drawback is that two images are created near the transmit frequency. Only one image is needed, the other being an exact duplicate. Unless the unwanted image is filtered, typically with analog components, transmit power is wasted and the usable bandwidth available in the system is reduced. A more efficient method of suppressing the unwanted image can be achieved by using a complex modulator followed by a quadrature modulator. Figure 78 is a block diagram of a quadrature modulator. Note that it is in fact the real output half of a complex modulator. The complete upconversion can actually be referred to as two complex upconversion stages, the real output of which becomes the transmitted signal. INPUT (REAL) OUTPUT INPUT (IMAGINARY) 90° The entire upconversion, from baseband to transmit frequency, is represented graphically in Figure 79. The resulting spectrum shown in Figure 79 represents the complex data consisting of COSωt Figure 78. Quadrature Modulator REAL CHANNEL (OUT) A/2 A/2 –FC1 FC –B/2J B/2J –FC FC REAL CHANNEL (IN) A DC COMPLEX MODULATOR TO QUADRATURE MODULATOR IMAGINARY CHANNEL (OUT) –A/2J A/2J –FC –FC B/2 B/2 –FC FC IMAGINARY CHANNEL (IN) B DC A/4 + B/4J A/4 – B/4J A/4 + B/4J A/4 – B/4J –FQ2 –FQ – FC –FQ + FC F Q – FC –A/4 – B/4J A/4 – B/4J A/4 + B/4J –A/4 + B/4J FQ FQ + F C OUT REAL QUADRATURE MODULATOR –FQ IMAGINARY FQ REJECTED IMAGES –FQ A/2 – B/2J FQ 1F = COMPLEX MODULATION FREQUENCY C 2F = QUADRATURE MODULATION FREQUENCY Q Figure 79. Two-Stage Upconversion and Resulting Image Rejection Rev. E | Page 37 of 56 02858-079 A/2 + B/2J 02858-078 SINωt AD9775 data on any channel. Image rejection on a channel occurs if either the real or imaginary data, or both, is present on the baseband channel. IMAGE REJECTION AND SIDEBAND SUPPRESSION OF MODULATED CARRIERS As shown in Figure 79, image rejection can be achieved by applying baseband data to the AD9775 and following the AD9775 with a quadrature modulator. To process multiple carriers while still maintaining image reject capability, each carrier must be complex modulated. As Figure 80 shows, single or multiple complex modulators can be used to synthesize complex carriers. These complex carriers are then summed and applied to the real and imaginary inputs of the AD9775. It is important to remember that the magnitude of a complex signal can be 1.414× the magnitude of its real or imaginary components. Due to this 3 dB increase in signal amplitude, the real and imaginary inputs to the AD9775 must be kept at least 3 dB below full scale when operating with the complex modulator. Overranging in the complex modulator results in severe distortion at the DAC output. COMPLEX BASEBAND SIGNAL A system in which multiple baseband signals are complex modulated and then applied to the AD9775 real and imaginary inputs followed by a quadrature modulator is shown in Figure 82, which also describes the transfer function of this system and the spectral output. Note the similarity of the transfer functions given in Figure 82 and Figure 80. Figure 82 adds an additional complex modulator stage for the purpose of summing multiple carriers at the AD9775 inputs. Also, as in Figure 79, the image rejection is not dependent on the real or imaginary baseband –ω1 – ω2 DC ω1 + ω2 FREQUENCY 02858-080 = REAL 1/2 Figure 80. Two-Stage Complex Upconversion R(1) MULTICARRIER REAL OUTPUT = R(1) + R(2) + . . .R(N) (TO REAL INPUT OF AD9775) R(1) R(2) COMPLEX MODULATOR 2 IMAGINARY INPUT BASEBAND CHANNEL N REAL INPUT ej(ω1 + ω2)t 1/2 COMPLEX MODULATOR 1 IMAGINARY INPUT BASEBAND CHANNEL 2 REAL INPUT × MULTICARRIER IMAGINARY OUTPUT = I(1) + I(2) + . . .I(N) (TO IMAGINARY INPUT OF AD9775) R(2) R(N) COMPLEX MODULATOR N R(N) = REAL OUTPUT OF N I(N) = IMAGINARY OUTPUT OF N 02858-081 BASEBAND CHANNEL 1 REAL INPUT 1 OUTPUT = REAL R(N) IMAGINARY INPUT Figure 81. Synthesis of Multicarrier Complex Signal MULTIPLE BASEBAND CHANNELS IMAGINARY MULTIPLE COMPLEX MODULATORS FREQUENCY = ω1, ω2...ωN REAL AD9775 COMPLEX MODULATOR FREQUENCY = ωC IMAGINARY REAL IMAGINARY REAL QUADRATURE MODULATOR FREQUENCY = ωQ COMPLEX BASEBAND SIGNAL × OUTPUT = REAL –ω1 – ωC – ωQ ej(ωN + ωC + ωQ)t ω1 + ωC + ωQ DC REJECTED IMAGES Figure 82. Image Rejection with Multicarrier Signals Rev. E | Page 38 of 56 02858-082 REAL AD9775 The complex carrier synthesized in the AD9775 digital modulator is accomplished by creating two real digital carriers in quadrature. Carriers in quadrature cannot be created with the modulator running at fDAC/2. As a result, complex modulation only functions with modulation rates of fDAC/4 and fDAC/8. Regions A and B of Figure 83 to Figure 88 are the result of the complex signal described previously, when complex modulated in the AD9775 by +ejωt. Regions C and D are the result of the complex signal described previously, again with positive frequency components only, modulated in the AD9775 by –ejωt. The analog quadrature modulator after the AD9775 inherently modulates by +ejωt. Region A Region A is a direct result of the upconversion of the complex signal near baseband. If viewed as a complex signal, only the images in Region A remain. The complex Signal A, consisting of positive frequency components only in the digital domain, has images in the positive odd Nyquist zones (1, 3, 5, …), as well as images in the negative even Nyquist zones. The appearance and rejection of images in every other Nyquist zone becomes more apparent at the output of the quadrature modulator. The A images appear on the real and the imaginary outputs of the AD9775, as well as on the output of the quadrature modulator, where the center of the spectral plot now represents the quadrature modulator LO, and the horizontal scale now represents the frequency offset from this LO. the high end of the DAC output spectrum in these graphs is the first null point for the sin(x)/x roll-off, and the asymmetry of the DAC output images is representative of the sin(x)/x roll-off over the spectrum. The internal PLL was enabled for these results. In addition, a 35 MHz third-order low-pass filter was used at the AD9775/AD8345 interface to suppress DAC images. An important point can be made by looking at Figure 91 and Figure 93. Figure 91 represents a group of positive frequencies modulated by complex +fDAC/4, while Figure 93 represents a group of negative frequencies modulated by complex −fDAC/4. When looking at the real or imaginary outputs of the AD9775, as shown in Figure 91 and Figure 93, the results look identical. However, the spectrum analyzer cannot show the phase relationship of these signals. The difference in phase between the two signals becomes apparent when they are applied to the AD8345 quadrature modulator, with the results shown in Figure 92 and Figure 94. 0 –20 D A B C D A B C –40 –60 –80 Region B is the image (complex conjugate) of Region A. If a spectrum analyzer is used to view the real or imaginary DAC outputs of the AD9775, Region B appears in the spectrum. However, on the output of the quadrature modulator, Region B is rejected. –100 –2.0 –1.5 –1.0 –0.5 0 0.5 1.0 1.5 2.0 02858-083 Region B (LO) fOUT (×fDATA) Figure 83. 2× Interpolation, Complex fDAC/4 Modulation Region C Region C is most accurately described as a downconversion, as the modulating carrier is –ejωt. If viewed as a complex signal, only the images in Region C remain. This image appears on the real and imaginary outputs of the AD9775, as well as on the output of the quadrature modulator, where the center of the spectral plot now represents the quadrature modulator LO and the horizontal scale represents the frequency offset from this LO. –20 Region D –60 D A B C D A B C –40 –80 –100 –4.0 Figure 89 to Figure 96 show the measured response of the AD9775 and AD8345 given the complex input signal to the AD9775 in Figure 89. The data in these graphs was taken with a data rate of 12.5 MSPS at the AD9775 inputs. The interpolation rate of 4× or 8× gives a DAC output data rate of 50 MSPS or 100 MSPS. As a result, Rev. E | Page 39 of 56 –3.0 –2.0 –1.0 0 1.0 2.0 3.0 4.0 (LO) fOUT (×fDATA) Figure 84. 4× Interpolation, Complex fDAC/4 Modulation 02858-084 Region D is the image (complex conjugate) of Region C. If a spectrum analyzer is used to view the real or imaginary DAC outputs of the AD9775, Region D appears in the spectrum. However, on the output of the quadrature modulator, Region D is rejected. 0 AD9775 0 –20 –20 D A B C D A B DA C –40 –40 –60 –60 –80 –80 –6.0 –4.0 –2.0 0 2.0 4.0 6.0 –100 –8.0 8.0 –6.0 –4.0 –2.0 02858-085 –100 –8.0 BC (LO) fOUT (×fDATA) DA BC 0 2.0 4.0 6.0 8.0 02858-088 0 (LO) fOUT (×fDATA) Figure 85. 8× Interpolation, Complex fDAC/4 Modulation Figure 88. 8× Interpolation, Complex fDAC/8 Modulation 0 0 –10 –20 –20 AMPLITUDE (dBm) –40 D A B CD A B –30 C –60 –40 –50 –60 –70 –80 –80 –90 –1.0 –0.5 0 0.5 1.0 1.5 –100 2.0 (LO) fOUT (×fDATA) 0 10 20 30 40 50 FREQUENCY (MHz) 02858-089 –1.5 02858-086 –100 –2.0 Figure 89. AD9775 Real DAC Output of Complex Input Signal Near Baseband (Positive Frequencies Only), Interpolation = 4×, No Modulation in AD9775 Figure 86. 2× Interpolation, Complex fDAC/8 Modulation 0 0 –10 –20 –20 AMPLITUDE (dBm) –40 D A B C D A B –30 C –60 –40 –50 –60 –70 –80 –80 –2.0 –1.0 0 1.0 2.0 3.0 4.0 (LO) fOUT (×fDATA) 02858-087 –3.0 –100 750 760 770 780 790 800 810 820 830 840 850 FREQUENCY (MHz) Figure 90. AD9775 Complex Output from Figure 89, Now Quadrature Modulated by AD8345 (LO = 800 MHz) Figure 87. 4× Interpolation, Complex fDAC/8 Modulation Rev. E | Page 40 of 56 02858-090 –90 –100 –4.0 0 0 –10 –10 –20 –20 –30 –30 AMPLITUDE (dBm) –40 –50 –60 –70 –40 –50 –60 –70 –80 –80 –100 750 10 20 30 40 50 FREQUENCY (MHz) 02858-091 0 780 790 800 810 820 830 840 850 Figure 94. AD9775 Complex Output from Figure 93, Now Quadrature Modulated by AD8345 (LO = 800 MHz) 0 0 –10 –10 –20 –20 –30 –30 AMPLITUDE (dBm) –40 –50 –60 –70 –40 –50 –60 –70 –80 –80 –90 –90 760 770 780 790 800 810 820 830 840 850 FREQUENCY (MHz) –100 02858-092 –100 750 0 20 40 60 80 100 FREQUENCY (MHz) Figure 92. AD9775 Complex Output from Figure 91, Now Quadrature Modulated by AD8345 (LO = 800 MHz) 02858-095 AMPLITUDE (dBm) 770 FREQUENCY (MHz) Figure 91. AD9775 Real DAC Output of Complex Input Signal Near Baseband (Positive Frequencies Only), Interpolation = 4×, Complex Modulation in AD9775 = +fDAC/4 Figure 95. AD9775 Real DAC Output of Complex Input Signal Near Baseband (Positive Frequencies Only), Interpolation = 8×, Complex Modulation in AD9775 = +fDAC/8 0 –10 –10 –20 –20 –30 –30 AMPLITUDE (dBm) 0 –40 –50 –60 –70 –40 –50 –60 –70 –80 –80 –90 –90 –100 0 10 20 30 40 50 FREQUENCY (MHz) 02858-093 AMPLITUDE (dBm) 760 02858-094 –90 –90 –100 –100 700 Figure 93. AD9775 Real DAC Output of Complex Input Signal Near Baseband (Negative Frequencies Only), Interpolation = 4×, Complex Modulation in AD9775 = −fDAC/4 720 740 760 780 800 820 840 860 880 900 FREQUENCY (MHz) Figure 96. AD9775 Complex Output from Figure 95, Now Quadrature Modulated by AD8345 (LO = 800 MHz) Rev. E | Page 41 of 56 02858-096 AMPLITUDE (dBm) AD9775 AD9775 APPLYING THE OUTPUT CONFIGURATIONS A single-ended output is suitable for applications requiring a unipolar voltage output. A positive unipolar output voltage results if IOUTA and/or IOUTB is connected to a load resistor, RLOAD, referred to AGND. This configuration is most suitable for a single-supply system requiring a dc-coupled, ground-referred output voltage. Alternatively, an amplifier could be configured as an I-V converter, thus converting IOUTA or IOUTB into a negative unipolar voltage. This configuration provides the best DAC dc linearity as IOUTA or IOUTB are maintained at ground or virtual ground. In many applications, it may be necessary to understand the equivalent DAC output circuit. This is especially useful when designing output filters or when driving inputs with finite input impedances. Figure 97 illustrates the output of the AD9775 and the equivalent circuit. A typical application where this information may be useful is when designing an interface filter between the AD9775 and Analog Devices’ AD8345 quadrature modulator. VOUT+ IOUTB VOUT– VSOURCE = 2 V p-p R OUT = 100 Ω Note that the output impedance of the AD9775 DAC itself is greater than 100 kΩ and typically has no effect on the impedance of the equivalent output circuit. DIFFERENTIAL COUPLING USING A TRANSFORMER An RF transformer can be used to perform a differential-tosingle-ended signal conversion, as shown in Figure 98. A differentially coupled transformer output provides the optimum distortion performance for output signals whose spectral content lies within the transformer’s pass band. An RF transformer, such as the Mini-Circuits T1-1T, provides excellent rejection of common-mode distortion (that is, even-order harmonics) and noise over a wide frequency range. It also provides electrical isolation and the ability to deliver twice the power to the load. Transformers with different impedance ratios can also be used for impedance matching purposes. IOUTA DAC IOUTB 02858-097 VOUT (DIFFERENTIAL) RLOAD The center tap on the primary side of the transformer must be connected to AGND to provide the necessary dc current path for both IOUTA and IOUTB. The complementary voltages appearing at IOUTA and IOUTB (that is, VOUTA and VOUTB) swing symmetrically around AGND and should be maintained within the specified output compliance range of the AD9775. A differential resistor, RDIFF, can be inserted in applications where the output of the transformer is connected to the load, RLOAD, via a passive reconstruction filter or cable. RDIFF is determined by the transformer’s impedance ratio and provides the proper source termination that results in a low VSWR. Note that approximately half the signal power dissipates across RDIFF. RA + R B VSOURCE = IOUTFS × (RA + RB) p-p MINI-CIRCUITS T1-1T Figure 98. Transformer-Coupled Output Circuit UNBUFFERED DIFFERENTIAL OUTPUT, EQUIVALENT CIRCUIT IOUTA For the typical situation, where IOUTFS = 20 mA and RA and RB both equal 50 Ω, the equivalent circuit values become 02858-098 The following sections illustrate typical output configurations for the AD9775. Unless otherwise noted, it is assumed that IOUTFS is set to a nominal 20 mA. For applications requiring optimum dynamic performance, a differential output configuration is suggested. A simple differential output may be achieved by converting IOUTA and IOUTB to a voltage output by terminating them to AGND via equal value resistors. This type of configuration may be useful when driving a differential voltage input device such as a modulator. If a conversion to a single-ended signal is desired and the application allows for ac coupling, an RF transformer may be useful, or if power gain is required, an op amp may be used. The transformer configuration provides optimum high frequency noise and distortion performance. The differential op amp configuration is suitable for applications requiring dc coupling, signal gain, and/or level shifting within the bandwidth of the chosen op amp. Figure 97. DAC Output Equivalent Circuit Rev. E | Page 42 of 56 AD9775 DIFFERENTIAL COUPLING USING AN OP AMP Gain/Offset Adjust An op amp can also be used to perform a differential-to-singleended conversion, as shown in Figure 99. This has the added benefit of providing signal gain as well. In Figure 99, the AD9775 is configured with two equal load resistors, RLOAD, of 25 Ω. The differential voltage developed across IOUTA and IOUTB is converted to a single-ended signal via the differential op amp configuration. An optional capacitor can be installed across IOUTA and IOUTB, forming a real pole in a low-pass filter. The addition of this capacitor also enhances the op amp distortion performance by preventing the DAC fast slewing output from overloading the input of the op amp. The matching of the DAC output to the common-mode input of the AD8345 allows the two components to be dc-coupled, with no level shifting necessary. The combined voltage offset of the two parts can therefore be compensated for via the AD9775 programmable offset adjust. This allows excellent LO cancellation at the AD8345 output. The programmable gain adjust allows for optimal image rejection as well. AD8021 DAC IOUTB COPT 225Ω 25Ω 500Ω ROPT 225Ω 02858-099 AVDD 25Ω Figure 99. Op Amp-Coupled Output Circuit The common-mode (and second-order distortion) rejection of this configuration is typically determined by the resistor matching. The op amp used must operate from a dual supply because its output is approximately ±1.0 V. A high speed amplifier, such as the AD8021, capable of preserving the differential performance of the AD9775 while meeting other system level objectives (such as cost and power) is recommended. The op amp differential gain, its gain setting resistor values, and full-scale output swing capabilities should all be considered when optimizing this circuit. ROPT is only necessary if level shifting is required on the op amp output. In Figure 99, AVDD, which is the positive analog supply for both the AD9775 and the op amp, is also used to level shift the differential output of the AD9775 to midsupply, that is, AVDD/2. INTERFACING THE AD9775 WITH THE AD8345 QUADRATURE MODULATOR The AD9775 architecture was defined to operate in a transmit signal chain using an image reject architecture. A quadrature modulator is also required in this application and should be designed to meet the output characteristics of the DAC as much as possible. The AD8345 from Analog Devices meets many of the requirements for interfacing with the AD9775. As with any DAC output interface, there are a number of issues that have to be resolved. The following sections list some of these issues. The performance of the AD9775 and AD8345 in an image reject transmitter, reconstructing three W-CDMA carriers, can be seen in Figure 100. The LO of the AD8345 in this application is 800 MHz. Image rejection (50 dB) and LO feedthrough (−78 dBFS) have been optimized with the programmable features of the AD9775. The average output power of the digital waveform for this test was set to −15 dBFS to account for the peak-to-average ratio of the W-CDMA signal. 0 –10 –20 –30 –40 –50 –60 –70 –80 –90 –100 762.5 DAC Compliance Voltage/Input Common-Mode Range The dynamic range of the AD9775 is optimal when the DAC outputs swing between ±1.0 V. The input common-mode range of the AD8345, at 0.7 V, allows optimum dynamic range to be achieved in both components. Rev. E | Page 43 of 56 782.5 802.5 822.5 842.5 FREQUENCY (MHz) Figure 100. AD9775/AD8345 Synthesizing a Three-Carrier W-CDMA Signal at an LO of 800 MHz 02858-100 225Ω IOUTA AMPLITUDE (dBm) 500Ω The AD9775 evaluation board includes an AD8345 and recommended interface (Figure 104 and Figure 105). On the output of the AD9775, R9 and R10 convert the DAC output current to a voltage. R16 may be used to do a slight commonmode shift if necessary. The (now voltage) signal is applied to a low-pass reconstruction filter to reject DAC images. The components installed on the AD9775 provide a 35 MHz cutoff but may be changed to fit the application. A balun (MiniCircuits ADTL1-12) is used to cross the ground plane boundary to the AD8345. Another balun (Mini-Circuits ETC1-1-13) is used to couple the LO input of the AD8345. The interface requires a low ac impedance return path from the AD8345, so a single connection between the AD9775 and AD8345 ground planes is recommended. AD9775 EVALUATION BOARD The AD9775 evaluation board allows easy configuration of the various modes, programmable via the SPI port. Software is available for programming the SPI port from PCs running Windows® 95, Windows 98, or Windows NT®/2000. The evaluation board also contains an AD8345 quadrature modulator and support circuitry that allows the user to optimally configure the AD9775 in an image reject transmit signal chain. Figure 101 to Figure 104 show how to configure the evaluation board in the one-port and two-port input modes with the PLL enabled and disabled. Refer to Figure 105 to Figure 114, the schematics, and the layout for the AD9775 evaluation board for the jumper locations described in the DAC Single-Ended Outputs section. The AD9775 outputs can be configured for various applications by referring to the following instructions. DAC Differential Outputs Transformers T2 and T3 should be in place. Note that the lower band of operation for these transformers is 300 kHz to 500 kHz. Jumper 4, Jumper 8, Jumper 13 to Jumper 17, and Jumper 28 to Jumper 30 should remain unsoldered. The outputs are taken from S3 and S4. Using the AD8345 Remove Transformers T2 and T3. Jumper JP4 and Jumper 28 to Jumper 30 should remain unsoldered. Jumper 13 to Jumper 16 should be soldered. The desired components for the low-pass interface filter L6, L7, C55, and C81 should be in place. The LO drive is connected to the AD8345 via J10 and the balun T4, and the AD8345 output is taken from J9. DAC Single-Ended Outputs Remove Transformers T2 and T3. Solder jumper links JP4 or JP28 to look at the DAC1 outputs. Solder jumper links JP29 or JP30 to look at the DAC2 outputs. Jumper 8 and Jumper 13 to Jumper 17 should remain unsoldered. Jumper JP35 to Jumper JP38 can be used to ground one of the DAC outputs while the other is measured single ended. Optimum single-ended distortion performance is typically achieved in this manner. The outputs are taken from S3 and S4. Rev. E | Page 44 of 56 AD9775 LECROY TRIG PULSE INP GENERATOR SIGNAL GENERATOR DATACLK INPUT CLOCK AWG2021 OR DG2020 CLK+/CLK– 40-PIN RIBBON CABLE DAC1, DB13–DB0 DAC2, DB13–DB0 AD9775 JUMPER CONFIGURATION FOR TWO-PORT MODE PLL ON SOLDERED/IN × UNSOLDERED/OUT × × × × × × × × × × × × NOTES 1. TO USE PECL CLOCK DRIVER, SOLDER JP41 AND JP42 AND REMOVE TRANSFORMER T1. 2. IN TWO-PORT MODE, IF DATACLK/PLL_LOCK IS PROGRAMMED TO OUTPUT PIN 8, JP25 AND JP39 SHOULD BE SOLDERED. IF DATACLK/PLL_LOCK IS PROGRAMMED TO OUTPUT PIN 53, JP46 AND JP47 SHOULD BE SOLDERED. SEE THE TWO-PORT DATA INPUT MODE FOR MORE INFORMATION. 02858-101 JP1 – JP2 – JP3 – JP5 – JP6 – JP12 – JP24 – JP25 – JP26 – JP27 – JP31 – JP32 – JP33 – Figure 101. Test Configuration for AD9775 in Two-Port Mode with PLL Enabled, Signal Generator Frequency = Input Data Rate, DAC Output Data Rate = Signal Generator Frequency × Interpolation Rate LECROY TRIG PULSE INP GENERATOR SIGNAL GENERATOR ONEPORTCLK INPUT CLOCK AWG2021 OR DG2020 CLK+/CLK– DAC1, DB13–DB0 DAC2, DB13–DB0 AD9775 JUMPER CONFIGURATION FOR ONE-PORT MODE PLL ON SOLDERED/IN × UNSOLDERED/OUT × × × × × × × × × × × × NOTES 1. TO USE PECL CLOCK DRIVER, SOLDER JP41 AND JP42 AND REMOVE TRANSFORMER T1. 02858-102 JP1 – JP2 – JP3 – JP5 – JP6 – JP12 – JP24 – JP25 – JP26 – JP27 – JP31 – JP32 – JP33 – Figure 102. Test Configuration for AD9775 in One-Port Mode with PLL Enabled, Signal Generator Frequency = One-Half Interleaved Input Data Rate, ONEPORTCLK = Interleaved Input Data Rate, DAC Output Data Rate = Signal Generator Frequency × Interpolation Rate Rev. E | Page 45 of 56 AD9775 LECROY TRIG PULSE INP GENERATOR SIGNAL GENERATOR DATACLK INPUT CLOCK AWG2021 OR DG2020 CLK+/CLK– 40-PIN RIBBON CABLE DAC1, DB13–DB0 DAC2, DB13–DB0 AD9775 JUMPER CONFIGURATION FOR TWO-PORT MODE PLL OFF SOLDERED/IN × UNSOLDERED/OUT × × × × × × × × × × × × NOTES 1. TO USE PECL CLOCK DRIVER, SOLDER JP41 AND JP42 AND REMOVE TRANSFORMER T1. 2. IN TWO-PORT MODE, IF DATACLK/PLL_LOCK IS PROGRAMMED TO OUTPUT PIN 8, JP25 AND JP39 SHOULD BE SOLDERED. IF DATACLK/PLL_LOCK IS PROGRAMMED TO OUTPUT PIN 53, JP46 AND JP47 SHOULD BE SOLDERED. SEE THE TWO-PORT DATA INPUT MODE FOR MORE INFORMATION. 02858-103 JP1 – JP2 – JP3 – JP5 – JP6 – JP12 – JP24 – JP25 – JP26 – JP27 – JP31 – JP32 – JP33 – Figure 103. Test Configuration for AD9775 in Two-Port Mode with PLL Disabled, DAC Output Data Rate = Signal Generator Frequency, DATACLK = Signal Generator Frequency/Interpolation Rate LECROY TRIG PULSE INP GENERATOR SIGNAL GENERATOR ONEPORTCLK INPUT CLOCK AWG2021 OR DG2020 CLK+/CLK– DAC1, DB13–DB0 DAC2, DB13–DB0 AD9775 JUMPER CONFIGURATION FOR ONE-PORT MODE PLL OFF SOLDERED/IN × UNSOLDERED/OUT × × × × × × × × × × × × NOTES 1. TO USE PECL CLOCK DRIVER, SOLDER JP41 AND JP42 AND REMOVE TRANSFORMER T1. 02858-104 JP1 – JP2 – JP3 – JP5 – JP6 – JP12 – JP24 – JP25 – JP26 – JP27 – JP31 – JP32 – JP33 – Figure 104. Test Configuration for AD9775 in One-Port Mode with PLL Disabled, DAC Output Data Rate = Signal Generator Frequency, ONEPORTCLK = Interleaved Input Data Rate = 2× Signal Generator Frequency/Interpolation Rate Rev. E | Page 46 of 56 Figure 105. AD8345 Circuitry on AD9775 Evaluation Board O1P O1N 2 + C72 10V 10μF 02858-105 BCASE VDDM O2P C54 DNP CC0603 LC0805 CC0805 C78 0.1μF C75 0.1μF C73 L5 DNP DNP CC0805 LC0805 L4 DNP C35 100pF CC0603 L7 DNP LC0805 C81 DNP 1 3 P 1 T6 S 6 4 2 2 1 11 10 AD8345 3 4 RC0603 R36 51Ω 1 C77 100pF CC0603 RC0603 7 8 P CC0603 C80 DNP T4 R37 DNP RC0603 JP20 S 5 4 JP18 R26 1kΩ VDDM 2 9 C76 100pF 3 ETC1-1-13 6 CC0603 R35 51Ω 5 U2 CC0603 C74 100pF R34 DNP R33 51Ω 12 4 T5 RC0603 JP19 CC0603 RC0603 RC0603 16 15 14 13 6 S P 3 QBBP IBBP CC0805 QBBN IBBN LC0805 G1B C55 DNP LOIN G2 O2N G4B G1A C79 DNP RC0603 ENBL ADTL1-12 G4A CC0603 VOUT LOIP G3 VPS1 VPS2 ADTL1-12 Rev. E | Page 47 of 56 CC0805 R32 51Ω RC0603 L6 DNP 2 R30 DNP 2 2 J9 DGND2; 3, 4, 5 JP21 JP7 2 2 LOCAL OSC INPUT R28 DGND2; 3, 4, 5 0Ω J10 RC0603 RC0603 R23 0Ω MODULATED OUTPUT J7 J3 J6 J4 J5 J8 W12 W11 CGND DCASE CLKVDD_IN AGND DCASE AVDD_IN DGND DCASE DVDD_IN DGND2 DCASE VDDMIN + C63 16V 22μF + C64 16V 22μF + C65 16V 22μF + C28 16V 22μF 2 c LC1210 L1 FERRITE LC1210 L2 FERRITE LC1210 L3 FERRITE LC1210 L8 FERRITE CC0805 CC0805 CC0805 CC0805 POWER INPUT FILTERS DCASE DCASE C69 0.1μF DCASE JP11 C68 0.1μF JP10 C67 0.1μF JP9 C32 0.1μF + C62 16V 22μF TP5 BLK + C61 16V 22μF TP3 BLK + C66 16V 22μF JP43 VDDM JP44 TP7 BLK TP6 RED CLKVDD TP4 RED AVDD TP2 RED DVDD JP45 AD9775 Figure 106. AD9775 Clock, Power Supplies, and Output Circuitry 2 3 JP12 CX2 CX1 02858-106 JP3 IQ JP40 JP27 JP5 C29 0.1μF JP25 RC0603 R39 1kΩ JP32 R5 49.9Ω TP14 WHT DVDD; 14 DGND; 7 11 DVDD; 14 DGND; 7 RC0603 R1 200Ω DVDD DVDD DVDD DVDD c + C7 BCASE 10μF 6.3V + C8 10μF 6.3V BCASE + C9 10μF 6.3V BCASE + C10 10μF 6.3V C42 0.1μF CC0603 0.001μF CC0603 C23 0.001μF CC0603 C24 0.001μF CC0603 C25 0.001μF CC0603 C26 CLKN CLKP 0.1μF C11 CC0603 0.1μF C12 BCASE BCASE C1 + 10μF 6.3V R38 10kΩ JP26 BD14 74VCX86 JP31 12 11 U4 13 U3 RC0603 JP23 74VCX86 CX3 C45 0.01μF OPCLK JP34 AGND; 3, 4, 5 OPCLK S5 IQ S6 DGND; 3, 4, 5 OPCLK_3 BD15 13 12 JP24 JP39 T1 T1-1T JP33 ADCLK 1 5 4 JP22 6 ACLKX c CGND; 3, 4, 5 S1 CLKIN JP2 JP1 C13 0.1μF CC0603 R40 DVDD 5kΩ DGND; 3, 4, 5 DATACLK S2 c TP15 WHT R3 1kΩ BD11 BD10 BD09 BD08 BD13 BD12 AD03 AD02 AD01 AD00 AD09 AD08 AD07 AD06 AD05 AD04 AD10 AD13 AD12 AD11 AD15 AD14 c CC0603 1pF C27 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 CC0805 DVDD AD9775+TSP CC0805 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 0.1μF C36 VDDC1 VDDA6 VSSA10 LF VDDC2 VDDA5 VSSC1 VSSA9 VDDA4 CLKP CLKN VSSA8 VSSA7 VSSC2 DCLK-PLLL IOUT1P VSSD1 IOUT1N VDDD1 VSSA6 VSSA5 P1D15 IOUT2P P1D14 IOUT2N P1D13 VSSA4 P1D12 VSSA3 P1D11 VDDA3 P1D10 VSSD2 VSSA2 VDDD2 U1 VDDA2 P1D9 VSSA1 VDDA1 P1D8 FSADJ1 P1D7 FSADJ2 P1D6 REFOUT P1D5 P1D4 RESET VSSD3 SP-CSB SP-CLK VDDD3 SP-SDI P1D3 SP-SDO P1D2 P1D1 VSSD6 VDDD6 P1D0 P2D0 P2D15-IQSEL P2D14-OPCLK P2D1 P2D2 P2D13 P2D3 P2D12 P2D4 VSSD4 VDDD4 P2D5 P2D11 VSSD5 VDDD5 P2D10 P2D9 P2D6 P2D7 P2D8 CC0603 CLKVDD CC0603 0.1μF CC0805 C37 CC0603 BD07 BD06 C22 0.001μF CC0603 CC0805 0.1μF CC0603 C16 TP8 WHT C6 + 10μF 6.3V C5 + 10μF 6.3V BCASE DVDD BCASE JP38 JP36 J35 J37 IQ JP46 R7 R8 2kΩ 1kΩ 0.01% 0.01% + C3 10μF 6.3V DVDD BCASE 0.1μF + C2 10μF 6.3V AVDD 0.1μF C41 AVDD BCASE C15 C4 + 10μF 6.3V TP9 WHT 0.1μF 0.1μF BCASE C14 C58 DNP CC0603 C17 CC0603 CC0805 0.1μF C40 C58 DNP CC0603 C19 0.1μF C39 R6 0.1μF 1kΩ BD00 C21 BD01 CC0603 BD02 0.001μF BD03 BD04 BD05 SPCSP SPCLK SPSDI SPSDO TP10 WHT 0.1μF TP11 WHT CC0805 C18 C59 DNP C57 DNP 0.1μF CC0603 C20 0.1μF CC0805 C38 CC0603 CC0603 RC0603 RC0603 CC0605 Rev. E | Page 48 of 56 CC0805 RC1206 CC0603 R2 1kΩ 5 6 2 1 U4 9 10 RC0603 RC0603 74VCX86 R11 51kΩ JP47 R17 10kΩ O1N O1P O2N O2P AGND; 3, 4, 5 OUT 2 S4 R42 49.9kΩ RC1206 AGND; 3, 4, 5 OUT1 S3 RC0603 SPSDO RC0603 CC0603 R43 49.9kΩ T1-1T JP17 R12 C70 51kΩ 0.1μF 4 3 T3 JP30 DVDD; 14 DGND; 7 8 JP14 JP15 JP29 JP16 JP13 5 6 2 1 JP8 CC0603 R16 10kΩ 4 T1-1T T2 JP28 JP4 RC0603 RC0603 C70 0.1μF 3 R9 51kΩ R10 51kΩ AD9775 Rev. E | Page 49 of 56 02858-107 13 15 17 19 21 23 25 27 29 31 33 35 37 39 14 16 18 20 22 24 26 28 30 32 34 36 38 40 RC1206 R15 220Ω 11 12 RIBBON J1 9 10 5 6 7 3 4 8 1 2 DATA-A 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 RP1 1 RP1 2 RP1 3 RP1 4 RP1 5 RP1 6 RP1 7 RP1 8 RP2 1 RP2 2 RP2 3 RP2 4 RP2 5 RP2 6 RP2 7 RP2 8 22Ω 16 22Ω 15 22Ω 14 22Ω 13 22Ω 12 22Ω 11 22Ω 10 22Ω 9 22Ω 16 22Ω 15 22Ω 14 22Ω 13 22Ω 12 22Ω 11 22Ω 10 22Ω 9 RCOM RP5 50Ω 10 1 R1 R2 R3 R4 R5 R6 R7 R8 R9 2 3 4 5 6 7 8 9 ADCLK OPCLK Figure 107. AD9775 Evaluation Board Input (A Channel) and Clock Buffer Circuitry K 2 74LCX112 U7 15 CLR CLK J Q 5 1 OPCLK_2 Q 6 2 U4 OPCLK_3 3 DVDD; 14 AGND; 7 74VCX86 11 J K 14 CLR CLK 74LCX112 U7 13 12 10 PRE 1 3 6 C52 + 4.7μF 6.3V DVDD C31 + 4.7μF 6.3V DVDD CX3 C30 + 4.7μF 6.3V DVDD AGND; 8 DVDD; 16 Q 7 Q 9 DVDD; 14 AGND; 7 74VCX86 U4 8 DVDD; 14 AGND; 7 PRE 5 4 U3 6 DVDD; 14 AGND; 7 74VCX86 U3 3 DVDD; 14 AGND; 7 74VCX86 U3 74VCX86 4 DVDD RP8 DNP AD00 AD01 AD02 AD03 AD04 AD05 AD06 9 10 5 4 2 1 AD07 CX2 CX1 AD08 AD09 AD10 AD11 AD12 AD13 AD14 AD15 RP7 10 DNP R1 R2 R3 R4 R5 R6 R7 R8 R9 9 10 RP6 1 2 3 4 5 6 7 8 9 10 50Ω RCOM RCOM R1 R2 R3 R4 R5 R6 R7 R8 R9 R1 R2 R3 R4 R5 R6 R7 R8 R9 1 1 RCOM ACASE ACASE ACASE C53 0.1μF C34 0.1μF C33 0.1μF CC0805 CC0805 CC0805 AD9775 Rev. E | Page 50 of 56 02858-108 33 35 37 39 34 36 38 40 RIBBON J2 31 32 23 24 29 21 22 30 19 20 27 17 18 28 15 16 25 13 14 26 11 7 8 12 5 6 9 3 4 10 1 2 DATA-B 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 RP4 22Ω RP4 22Ω RP4 22Ω RP4 22Ω RP4 22Ω RP4 22Ω RP4 22Ω RP4 22Ω RP3 22Ω RP3 22Ω RP3 22Ω RP3 22Ω RP3 22Ω RP3 22Ω RP3 22Ω RP3 22Ω 9 10 11 12 13 14 15 16 9 10 11 12 13 14 15 2 3 4 5 6 7 8 9 BD00 BD01 BD02 BD03 BD04 BD05 BD06 BD07 BD08 BD09 BD10 BD11 BD12 BD13 BD14 BD15 RP9 10 DNP R1 R2 R3 R4 R5 R6 R7 R8 R9 16 RCOM RP12 10 50Ω 1 R1 R2 R3 R4 R5 R6 R7 R8 R9 Figure 108. AD9775 Evaluation Board Input (B Channel) and SPI Port Circuitry ACASE DVDD SPSDO SPSDI SPCLK SPCSB + C43 4.7μF CC805 6.3V 9 10 RP11 1 2 3 4 5 6 7 8 9 10 RP10 50Ω RCOM DNP RCOM R1 R2 R3 R4 R5 R6 R7 R8 R9 R1 R2 R3 R4 R5 R6 R7 R8 R9 1 1 RCOM C50 0.1μF 2 c U5 + C49 4.7μF 6.3V U5 U5 U5 10 U5 74AC14 8 U5 U6 12 DGND; 7 DVDD; 14 U6 U6 6 DGND; 7 74AC14 DVDD; 14 5 DGND; 7 74AC14 DVDD; 14 3 U6 U6 8 DGND; 7 74AC14 DVDD; 14 9 DGND; 7 74AC14 DVDD; 14 11 10 13 9 DGND; 7 DVDD; 14 11 DGND; 7 DVDD; 14 12 RC0805 ACASE DVDD + RC0805 C44 4.7μF 6.3V RC0805 R24 DNP RC0805 R22 DNP JP41 JP42 RC0805 R20 DNP R21 DNP RC0805 RC0805 R45 9kΩ R48 9kΩ R50 9kΩ CLKVDD; 8 CGND; 5 4 2 DGND; 7 DVDD; 14 74AC14 5 CC805 C48 1nF R19 100Ω CC805 MC100EPT22 3 6 U8 4 R18 200Ω RC0805 DGND; 7 74AC14 DVDD; 14 3 c 1 2 CGND; 5 CLKVDD; 8 U8 13 c RC0805 MC100EPT22 c C47 1nF DGND; 7 74AC14 DVDD; 14 U6 C60 0.1μF c 7 R13 120Ω DGND; 7 DVDD; 14 1 CC805 RC0805 R4 120Ω R14 200Ω DGND; 7 74AC14 DVDD; 14 1 74AC14 6 74AC14 4 74AC14 ACASE CLKDD ACLKX CC805 C46 0.1μF RC0805 CLKVDD CLKVDD CLKN CLKP CLKVDD CC805 6 5 4 3 2 C51 0.1μF SPI PORT P1 1 c c AD9775 02858-109 AD9775 02858-110 Figure 109. AD9775 Evaluation Board Components, Top Side Figure 110. AD9775 Evaluation Board Components, Bottom Side Rev. E | Page 51 of 56 02858-111 AD9775 02858-112 Figure 111. AD9775 Evaluation Board Layout, Layer One (Top) Figure 112. AD9775 Evaluation Board Layout, Layer Two (Ground Plane) Rev. E | Page 52 of 56 02858-113 AD9775 02858-114 Figure 113. AD9775 Evaluation Board Layout, Layer Three (Power Plane) Figure 114. AD9775 Evaluation Board Layout, Layer Four (Bottom) Rev. E | Page 53 of 56 AD9775 OUTLINE DIMENSIONS 14.20 14.00 SQ 13.80 0.75 0.60 0.45 1.20 MAX 12.20 12.00 SQ 11.80 80 61 61 1 60 80 1 60 PIN 1 EXPOSED PAD TOP VIEW (PINS DOWN) BOTTOM VIEW 0° MIN 1.05 1.00 0.95 0.15 0.05 SEATING PLANE 6.00 BSC SQ 0.20 0.09 7° 3.5° 0° 0.08 MAX COPLANARITY (PINS UP) 20 41 40 21 VIEW A 41 20 21 40 0.50 BSC LEAD PITCH 0.27 0.22 0.17 VIEW A ROTATED 90° CCW COMPLIANT TO JEDEC STANDARDS MS-026-ADD-HD Figure 115. 80-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP] (SV-80-1) Dimensions shown in millimeters ORDERING GUIDE Model AD9775BSV AD9775BSVRL AD9775BSVZ 1 AD9775BSVZRL1 AD9775-EB 1 Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C Package Description 80-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP] 80-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP] 80-Lead, Thin Quad Flat Package, Exposed Pad [TQFP_EP] 80-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP] Evaluation Board Z = Pb-free part. Rev. E | Page 54 of 56 Package Option SV-80-1 SV-80-1 SV-80-1 SV-80-1 AD9775 NOTES Rev. E | Page 55 of 56 AD9775 NOTES ©2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C02858-0-12/06(E) Rev. E | Page 56 of 56