Order
Now
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
TPS55330
SLVSBX8B – MAY 2013 – REVISED JANUARY 2019
TPS55330 Integrated 5-A, 24-V Boost/SEPIC/Flyback DC-DC Regulator
1 Features
3 Description
•
•
•
•
•
•
•
•
•
•
The TPS55330 is a monolithic nonsynchronous
switching regulator with integrated 5-A, 24-V power
switch. The device can be configured in several
standard switching-regulator topologies, including
boost, SEPIC, and isolated flyback. The device has a
wide input voltage range to support applications with
input voltage from multicell batteries or regulated 3.3V, 5-V, and 12-V power rails.
1
•
•
•
•
Internal 5-A, 24-V Low-Side MOSFET Switch
2.9-V to 16-V Input Voltage Range
±0.7% Reference Voltage
0.5-mA Operating Quiescent Current
2.7-µA Shutdown Supply Current
Fixed-Frequency-Current-Mode PWM Control
Frequency Adjustable From 100 kHz to 1.2 MHz
Synchronization Capability to External Clock
Adjustable Soft-Start Time
Pulse-Skipping for Higher Efficiency at Light
Loads
Cycle-by-Cycle Current Limit, Thermal Shutdown,
and UVLO Protection
QFN-16 (3 mm × 3 mm) With PowerPAD™
Wide –40°C to +150°C Operating TJ Range
Create a Custom Design Using the TPS55330
With the WEBENCH® Power Designer
2 Applications
•
•
•
•
•
3.3-V, 5-V, 12-V Power Conversion
Boost, SEPIC, and Flyback Topologies
Thunderbolt Port, Power Docking for Tablets and
Portable PCs
Industrial Power Systems
ADSL Modems
The TPS55330 regulates the output voltage with
current mode PWM (pulse width modulation) control,
and has an internal oscillator. The switching
frequency of PWM is set by either an external resistor
or by synchronizing to an external clock signal. The
user can program the switching frequency from
100 kHz to 1.2 MHz.
The device features a programmable soft-start
function to limit inrush current during start up and has
other built-in protection features including cycle-bycycle overcurrent limit and thermal shutdown.
The TPS55330 is available in a small 3-mm × 3-mm
16-pin QFN with PowerPAD for enhanced thermal
performance.
Device Information(1)
PART NUMBER
TPS55330
VIN
BODY SIZE (NOM)
WQFN (16)
3.00 mm × 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Typical Application (Boost)
L
PACKAGE
Efficiency vs Output Current
D
100
VOUT
95
CO
TPS55330
VIN
SW
EN
SW
FREQ
SW
RSH
SS
FB
COMP
PGND
SYNC
PGND
AGND
PGND
CSS
RFREQ
RC
CC
90
Efficiency (%)
CI
85
80
75
fSW = 600 kHz
VOUT = 5 V
70
65
RSL
VIN = 2.9 V
VIN = 3.6 V
VIN = 4.2 V
60
55
50
0
0.5
1
1.5
2
Output Current (A)
2.5
3
G017
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPS55330
SLVSBX8B – MAY 2013 – REVISED JANUARY 2019
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
4
4
4
4
5
6
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 9
7.1
7.2
7.3
7.4
Overview ................................................................... 9
Functional Block Diagram ......................................... 9
Feature Description................................................... 9
Device Functional Modes........................................ 12
8
Application and Implementation ........................ 13
8.1 Application Information............................................ 13
8.2 Typical Application .................................................. 13
9 Power Supply Recommendations...................... 22
10 Layout................................................................... 22
10.1 Layout Guidelines ................................................. 22
10.2 Layout Example .................................................... 22
10.3 Thermal Considerations ........................................ 23
11 Device and Documentation Support ................. 24
11.1
11.2
11.3
11.4
11.5
11.6
Device Support......................................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
24
24
24
24
24
25
12 Mechanical, Packaging, and Orderable
Information ........................................................... 25
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision A (October 2014) to Revision B
Page
•
Added links for Webench ....................................................................................................................................................... 1
•
Added text note under pin configuration diagram................................................................................................................... 3
Changes from Original (May 2013) to Revision A
•
2
Page
Added Pin Configuration and Functions section, ESD Rating table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Submit Documentation Feedback
Copyright © 2013–2019, Texas Instruments Incorporated
Product Folder Links: TPS55330
TPS55330
www.ti.com
SLVSBX8B – MAY 2013 – REVISED JANUARY 2019
5 Pin Configuration and Functions
SW
1
VIN
2
SW
SW
NC
PGND
16-Pin RTE
QFN Package
Top View
16
15
14
13
12
PGND
11
PGND
NC
PowerPAD
4
9
5
6
7
8
FB
SS
COMP
10
AGND
3
SYNC
EN
FREQ
TI recommends connecting NC with AGND.
Pin Functions
PIN
NAME
VIN
DESCRIPTION
NUMBER
2
The input supply pin to the IC. Connect VIN to a supply voltage between 2.9 V and 16 V. It is acceptable for
the voltage on the pin to be different from the boost power stage input.
SW
1, 15, 16
FB
8
Error amplifier input and feedback pin for positive voltage regulation. Connect to the center tap of a resistor
divider to program the output voltage.
EN
3
Enable pin. When the voltage of this pin falls below the enable threshold for more than 1 ms, the IC turns
off.
COMP
7
Output of the transconductance error amplifier. An external RC network connected to this pin compensates
the regulator feedback loop.
SS
4
Soft-start programming pin. A capacitor between the SS pin and AGND pin programs soft-start timing.
FREQ
9
Switching frequency program pin. An external resistor connected between the FREQ pin and AGND sets the
switching frequency.
AGND
6
Signal ground of the IC.
PGND
11, 12, 13
SYNC
5
NC
PowerPAD
10, 14
17
SW is the drain of the internal power MOSFET. Connect SW to the switched side of the boost or SEPIC
inductor or the flyback transformer.
Power ground of the IC. It is connected to the source of the internal power MOSFET switch.
Switching frequency synchronization pin. An external clock signal can be used to set the switching frequency
between 200 kHz and 1 MHz. If not used, this pin should be tied to AGND.
Reserved pin that must be connected to ground.
Solder the PowerPAD to the AGND. If possible, use thermal vias to connect to internal ground plane for
improved power dissipation.
Submit Documentation Feedback
Copyright © 2013–2019, Texas Instruments Incorporated
Product Folder Links: TPS55330
3
TPS55330
SLVSBX8B – MAY 2013 – REVISED JANUARY 2019
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings (1)
over operating temperature range (unless otherwise noted)
Supply voltages on pin VIN (2)
Voltage on pin EN
(2)
(1)
(2)
MAX
UNIT
18
V
–0.3
18
V
Voltage on pins FB, FREQ, and COMP (2)
–0.3
3
V
Voltage on pin SS (2)
–0.3
5
V
V
Voltage on pin SYNC
Tstg
MIN
–0.3
(2)
–0.3
7
Voltage on pin SW (2)
–0.3
24
V
Operating junction temperature range
–40
150
°C
Storage temperature range
–65
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to network ground pin
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±2000
Charged-device model (CDM), per JEDEC specification JESD22C101 (2)
±500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
MIN
MAX
UNIT
VIN
Input voltage range
2.9
16
V
VOUT
Output voltage range
VIN
22
V
VEN
EN voltage range
0
16
V
VSYN
External switching frequency logic input range
0
5
V
TA
Operating free-air temperature
–40
125
°C
TJ
Operating junction temperature
–40
150
°C
6.4 Thermal Information
TPS55330
THERMAL METRIC (1)
QFN
UNIT
16 PINS
RθJA
Junction-to-ambient thermal resistance
43.3
RθJC(top)
Junction-to-case (top) thermal resistance
38.7
RθJB
Junction-to-board thermal resistance
14.5
ψJT
Junction-to-top characterization parameter
0.4
ψJB
Junction-to-board characterization parameter
14.5
RθJC(bot)
Junction-to-case (bottom) thermal resistance
3.5
(1)
4
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2013–2019, Texas Instruments Incorporated
Product Folder Links: TPS55330
TPS55330
www.ti.com
SLVSBX8B – MAY 2013 – REVISED JANUARY 2019
6.5 Electrical Characteristics
VIN = 5 V, TJ = –40°C to +150°C, unless otherwise noted. Typical values are at TA = 25°C.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY CURRENT
VIN
Input voltage range
IQ
Operating quiescent current into VIN
Device non-switching, VFB = 2 V
2.9
0.5
16
ISD
Shutdown current
EN = GND
2.7
VUVLO
Under-voltage lockout threshold
VIN falling
Vhys
Under-voltage lockout hysteresis
V
mA
10
µA
2.5
2.7
V
120
140
160
mV
ENABLE AND REFERENCE CONTROL
VEN(r)
EN threshold voltage
EN rising input
0.9
1.08
1.30
V
VEN(f)
EN threshold voltage
EN falling input
0.74
0.92
1.125
V
VENh
EN threshold hysteresis
REN
EN pulldown resistor
Toff
Shutdown delay, SS discharge
VSYNh
SYN logic high voltage
VSYNl
SYN logic low voltage
0.16
400
EN high to low
950
V
1600
1.0
kΩ
ms
1.2
0.4
V
VOLTAGE AND CURRENT CONTROL
1.204
1.229
1.254
1.220
1.229
1.238
TA = 25°C
1.6
20
VFB = VREF + 200 mV, VCOMP = 1 V
42
µA
Comp pin source current
VFB = VREF – 200 mV, VCOMP = 1 V
42
µA
VCCLP
Comp pin Clamp Voltage
High Clamp, VFB = 1 V
Low Clamp, VFB = 1.5 V
3.1
0.75
V
VCTH
Comp pin threshold
Duty cycle = 0%
1.04
V
Gea
Error amplifier transconductance
Rea
Error amplifier output resistance
fea
Error amplifier crossover frequency
VREF
Voltage feedback regulation voltage
IFB
Voltage feedback input bias current
Isink
Comp pin sink current
Isource
TA = 25°C
240
360
440
V
nA
µS
10
MΩ
500
kHz
FREQUENCY
fSW
Frequency
Dmax
Maximum duty cycle
VFREQ
FREQ pin voltage
Tmin_on
Minimum on pulse width
RFREQ = 480 kΩ
75
94
RFREQ = 80 kΩ
460
577
740
RFREQ = 40 kΩ
920
1140
1480
89%
96%
VFB = 1.0 V, RFREQ = 80 kΩ
130
kHz
1.25
V
RFREQ = 80 kΩ
77
ns
60
70
POWER SWITCH
RDS(ON)
N-channel MOSFET on-resistance
VIN = 5 V
VIN = 3 V
ILN_NFET
N-channel leakage current
VDS = 25 V, TA = 25°C
110
120
mΩ
2.1
µA
7.75
A
OCP and SS
ILIM
N-Channel MOSFET current limit
D = Dmax
ISS
Soft-start bias current
VSS = 0 V
5.25
6.6
6
µA
THERMAL SHUTDOWN
Tshutdown
Thermal shutdown threshold
165
°C
Thysteresis
Thermal shutdown threshold
hysteresis
15
°C
Submit Documentation Feedback
Copyright © 2013–2019, Texas Instruments Incorporated
Product Folder Links: TPS55330
5
TPS55330
SLVSBX8B – MAY 2013 – REVISED JANUARY 2019
www.ti.com
6.6 Typical Characteristics
VIN = 5 V, TA = 25°C (unless otherwise noted)
8
Current Limit Threshold (A)
Transconductance (µA/V)
400
380
360
340
320
7
6
5
4
3
2
300
−50
−25
0
25
50
75
Temperature (°C)
100
125
1
−50
150
Figure 1. Error Amplifier Transconductance vs Temperature
125
150
G002
VIN = 3 V
Resistance (mΩ)
Voltage Reference (V)
100
100
1.228
1.226
1.224
80
60
VIN = 12 V
40
VIN = 5 V
20
1.22
−50
−25
0
25
50
75
Temperature (°C)
100
125
0
−50
150
−25
0
G003
Figure 3. Feedback Voltage Reference vs Temperature
1600
1400
1400
1200
Frequency (kHz)
1000
800
600
400
25
50
75
Temperature (°C)
30
100
Resistance (kΩ)
500
125
150
G004
1000
800
600
RFREQ = 40 kΩ
RFREQ = 80 kΩ
RFREQ = 480 kΩ
400
200
200
100
Figure 4. RDS(ON) vs Temperature
1200
Frequency (kHz)
25
50
75
Temperature (°C)
120
1.222
0
−50
G005
Figure 5. Frequency vs FREQ Resistance
6
0
Figure 2. Switch Current Limit vs Temperature
1.23
0
−25
G001
Submit Documentation Feedback
−25
0
25
50
75
Temperature (°C)
100
125
150
G006
Figure 6. Frequency vs Temperature
Copyright © 2013–2019, Texas Instruments Incorporated
Product Folder Links: TPS55330
TPS55330
www.ti.com
SLVSBX8B – MAY 2013 – REVISED JANUARY 2019
Typical Characteristics (continued)
VIN = 5 V, TA = 25°C (unless otherwise noted)
400
700
350
600
300
500
Frequency (kHz)
Frequency (kHz)
RFREQ = 80 kΩ
250
200
150
100
400
Non-Foldback
Foldback
300
200
100
50
0
−50
0
0
5
10
15
20
25
30
Voltage on the VIN Pin (V)
35
−25
0
40
25
50
75
Temperature (°C)
100
125
150
G007
D006
TA = 25°C
Figure 7. Minimum Switching Frequency for Quick Recovery
from Frequency Foldback
Figure 8. Non-Foldback Frequency vs Foldback Frequency
3.5
2.7
2.66
Input Voltage (V)
COMP Voltage (V)
3
2.5
COMP Pin Clamp High
COMP Pin Clamp Low
2
1.5
2.62
UVLO Start
UVLO Stop
2.58
2.54
1
0.5
−50
−25
0
25
50
75
Temperature (°C)
100
125
2.5
−50
150
Figure 9. COMP Clamp Voltage vs Temperature
25
50
75
Temperature (°C)
100
125
150
G009
100
RFREQ = 80 kΩ
EN Voltage Rising
EN Voltage Falling
Maximum Duty Cycle (%)
1.2
Enable Voltage (V)
0
Figure 10. Input Voltage UVLO vs Temperature
1.3
1.1
1
0.9
0.8
0.7
−50
−25
G008
99
98
97
96
95
−25
0
25
50
75
Temperature (°C)
100
125
150
94
−50
G010
Figure 11. Enable Voltage vs Temperature
−25
0
25
50
75
Temperature (°C)
100
125
150
G011
Figure 12. Maximum Duty Cycle vs Temperature
Submit Documentation Feedback
Copyright © 2013–2019, Texas Instruments Incorporated
Product Folder Links: TPS55330
7
TPS55330
SLVSBX8B – MAY 2013 – REVISED JANUARY 2019
www.ti.com
Typical Characteristics (continued)
VIN = 5 V, TA = 25°C (unless otherwise noted)
100
8
RFREQ = 80 kΩ
7
Shutdown Current (µA)
Minimum On Time (ns)
95
90
85
80
75
6
5
4
3
2
70
−50
−25
0
25
50
75
Temperature (°C)
100
125
1
−50
150
−25
0
25
50
75
Temperature (°C)
G012
Figure 13. Minimum On Time vs Temperature
100
125
150
G013
Figure 14. Shutdown Current vs Temperature
2.1
Supply Current (mA)
1.8
1.5
Switching
Non-Switching
1.2
0.9
0.6
0.3
−50
−25
0
25
50
75
Temperature (°C)
100
125
150
G014
Figure 15. Supply Current vs Temperature
8
Submit Documentation Feedback
Copyright © 2013–2019, Texas Instruments Incorporated
Product Folder Links: TPS55330
TPS55330
www.ti.com
SLVSBX8B – MAY 2013 – REVISED JANUARY 2019
7 Detailed Description
7.1 Overview
The TPS55330 device is a monolithic nonsynchronous switching regulator with an integrated 5-A, 24-V power
switch. The device can be configured in several standard switching-regulator topologies, including boost, SEPIC,
and isolated flyback. The device has a wide input voltage range to support applications with input voltage from
multicell batteries or regulated 3.3-V, 5-V, and 12-V power rails.
7.2 Functional Block Diagram
VIN
SW
FB
Error
Amp
EN
1.229V
Reference
COMP
PWM
Control
Ramp
Generator
Gate
Driver
Lossless
Current Sense
S
Oscillator
SS
FREQ
SYNC
AGND
PGND
7.3 Feature Description
7.3.1 Operation
If designed as a boost converter, the TPS55330 device regulates the output with current-mode pulse-widthmodulation (PWM) control. The PWM-control circuitry turns on the switch at the beginning of each oscillator clock
cycle. The input voltage is applied across the inductor and stores the energy as inductor current ramps up.
During this portion of the switching cycle, the load current is provided by the output capacitor. When the inductor
current reaches a threshold level set by the error amplifier output, the power switch turns off and the external
Schottky diode is forward biased to allow the inductor current to flow to the output. The inductor transfers stored
energy to replenish the output capacitor and supply the load current. This operation repeats every switching
cycle. The duty cycle of the converter is determined by the PWM-control comparator which compares the error
amplifier output and the current signal. The oscillator frequency is programmed by the external resistor or
synchronized to an external clock signal.
Submit Documentation Feedback
Copyright © 2013–2019, Texas Instruments Incorporated
Product Folder Links: TPS55330
9
TPS55330
SLVSBX8B – MAY 2013 – REVISED JANUARY 2019
www.ti.com
Feature Description (continued)
A ramp signal from the oscillator is added to the inductor current ramp to provide slope compensation. Slope
compensation is required to avoid subharmonic oscillation that is intrinsic to peak-current mode control at duty
cycles higher than 50%. If the inductor value is too small, the internal slope compensation may not be adequate
to maintain stability.
The PWM control feedback loop regulates the FB pin to a reference voltage through a transconductance error
amplifier. The output of the error amplifier is connected to the COMP pin. An external RC-compensation network
connected to the COMP pin is chosen for feedback loop stability and optimum transient response.
7.3.2 Switching Frequency
The switching frequency is set by a resistor (RFREQ) connected to the FREQ pin of the TPS55330. The
relationship between the timing resistance RFREQ and frequency is shown in the Figure 5. Do not leave this pin
open. A resistor must always be connected from the FREQ pin to ground for proper operation. The resistor value
required for a desired frequency can be calculated using Equation 1.
RFREQ(kΩ) = 57500 × ƒsw(kHz)–1.03
(1)
For the given resistor value, the corresponding frequency can be calculated by Equation 2.
ƒsw(kHz) = 41600 × RFREQ(kΩ)–0.97
(2)
The TPS55330 switching frequency can be synchronized to an external clock signal that is applied to the SYNC
pin. The required logic levels of the external clock are shown in the specification table. The recommended duty
cycle of the clock is in the range of 10% to 90%. A resistor must be connected from the FREQ pin to ground
when the converter is synchronized to the external clock and the external clock frequency must be within ±20%
of the corresponding frequency set by the resistor. For example, if the frequency programmed by the FREQ pin
resistor is 600kHz, the external clock signal should be in the range of 480kHz to 720kHz.
With a switching frequency below 280 kHz (typical) after the TPS55330 enters frequency foldback as described
in the section, if a load remains when the overcurrent condition is removed the output may not recover to the set
value. For the output to return to the set value the load must be removed completely or the TPS55330 power
cycled with the EN pin or VIN pin. Select a nominal switching frequency of 350 kHz for quicker recovery from
frequency foldback.
7.3.3 Overcurrent Protection and Frequency Foldback
The TPS55330 provides cycle-by-cycle over-current protection that turns off the power switch once the inductor
current reaches the over-current limit threshold. The PWM circuitry resets itself at the beginning of the next
switch cycle. During an over-current event, the output voltage begins to droop as a function of the load on the
output. When the FB voltage through the feedback resistors, drops lower than 0.9 V, the switching frequency is
automatically reduced to 1/4 of the normal value. Figure 8 shows the non-foldback frequency with an 80kΩ timing
resistor and the corresponding foldback frequency. The switching frequency does not return to normal until the
over-current condition is removed and the FB voltage increases above 0.9 V. The frequency foldback feature is
disabled during soft-start.
7.3.3.1 Minimum On-Time and Pulse Skipping
The TPS55330 PWM control system has a minimum PWM pulse width of 77ns (typical). This minimum on-time
determines the minimum duty cycle of the PWM, for any set switching frequency. When the voltage regulation
loop of the TPS55330 requires a minimum on-time pulse width less than 77ns, the IC enters pulse-skipping
mode. In this mode, the device will hold the power switch off for several switching cycles to prevent the output
voltage from rising above the desired regulated voltage. This operation typically occurs in light load conditions
when the PWM operates in discontinuous conduction mode. Pulse skipping increases the output ripple as shown
in Figure 22.
7.3.4 Voltage Reference and Setting Output Voltage
An internal voltage reference provides a precise 1.229 V voltage reference at the error amplifier non-inverting
input. To set the output voltage, select the FB pin resistor RSH and RSL according to Overcurrent Protection and
Frequency Foldback.
10
Submit Documentation Feedback
Copyright © 2013–2019, Texas Instruments Incorporated
Product Folder Links: TPS55330
TPS55330
www.ti.com
SLVSBX8B – MAY 2013 – REVISED JANUARY 2019
Feature Description (continued)
æR
ö
VOUT = 1.229 V ´ ç SH + 1÷
è R SL
ø
(3)
7.3.5 Soft-Start
The TPS55330 has a built-in soft-start circuit which significantly reduces the start-up current spike and output
voltage overshoot. When the IC is enabled, an internal bias current source (6 µA typical) charges a capacitor
(CSS) on the SS pin. The voltage at the capacitor clamps the output of the internal error amplifier that determines
the peak current and duty cycle of PWM controller. Limiting the peak switch current during start-up with a slow
ramp on the SS pin will reduce in-rush current and output voltage overshoot. Once the capacitor reaches 1.8V,
the soft-start cycle is completed and the soft-start voltage no longer clamps the error amplifier output. When the
EN is pulled low for at least 1ms, the IC enters the shutdown mode and the SS capacitor is discharged through a
5kΩ resistor to prepare for the next soft-start sequence.
7.3.6 Slope Compensation
The TPS55330 has internal slope compensation to prevent subharmonic oscillations. The sensed current slope
of boost converter can be expressed as Equation 4:
V
Sn = IN ´ RSENSE
(4)
L
The slope compensation dv/dt can be calculated using Equation 5.
0.32 V RFREQ 0.5 mA
Se =
+
16 ´ (1 - D) ´ 6 pF
6 pF
(5)
In a converter with current mode control, in addition to the output voltage feedback loop, the inner current loop
including the inductor current sampling effect as well as the slope compensation on the small signal response
should be taken into account, which can be modeled as seen in Equation 6:
1
He(s) =
éæ
ù
S ö
s ´ êç 1 + e ÷ ´ (1 - D) - 0.5 ú
Sn ÷ø
êëçè
úû
s2
1+
+
2
fsw
p ´ fsw
(
)
where
•
•
•
RSENSE (15mΩ) is the equivalent current sense resistor
RFREQ is timing resistor used to set frequency
D is the duty cycle
(6)
NOTE
If Sn