NTHL080N120SC1

MOSFET - SiC Power, Single N-Channel 1200 V, 80 mW, 31 A NTHL080N120SC1 Features • • • • • Typ. RDS(on) = 80 mW Ultra Low Gate Charge (typ. QG(tot) = 56 nC) Low Effective Output Capacitance (typ. Coss = 80 pF) 100% UIL Tested These Devices are RoHS Compliant www.onsemi.com V(BR)DSS RDS(on) MAX ID MAX 1200 V 110 mW @ 20 V 31 A Typical Applications • UPS • DC/DC Converter • Boost Inverter N−CHANNEL MOSFET D MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Parameter Symbol Value Unit Drain−to−Source Voltage VDSS 1200 V Gate−to−Source Voltage VGS −15/+25 V VGSop −5/+20 V ID 31 A PD 178 W ID 22 A Recommended Operation Values of Gate−to− Source Voltage TC < 175°C Steady State Continuous Drain Current RqJC TC = 25°C Power Dissipation RqJC Steady TC = 100°C State Continuous Drain Current RqJC Power Dissipation RqJC Pulsed Drain Current (Note 2) TA = 25°C Single Pulse Surge Drain TA = 25°C, tp = 10 ms, Current Capability RG = 4.7 W Operating Junction and Storage Temperature Range Source Current (Body Diode) Single Pulse Drain−to−Source Avalanche Energy (IL(pk) = 18.5 A, L = 1 mH) (Note 3) PD 89 W IDM 132 A IDSC 132 A TJ, Tstg −55 to +175 °C IS 18 A EAS 171 mJ G S G D S TO−247−3LD CASE 340CX MARKING DIAGRAM $Y&Z&3&K NTHL080 N120SC1 Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. THERMAL RESISTANCE MAXIMUM RATINGS Parameter Symbol Value Unit Junction−to−Case (Note 1) RqJC 0.84 °C/W Junction−to−Ambient (Note 1) RqJA 40 °C/W 1. The entire application environment impacts the thermal resistance values shown, they are not constants and are only valid for the particular conditions noted. 2. Repetitive rating, limited by max junction temperature. 3. EAS of 171 mJ is based on starting TJ = 25°C; L = 1 mH, IAS = 18.5 A, VDD = 120 V, VGS = 18 V. © Semiconductor Components Industries, LLC, 2018 April, 2020 − Rev. 4 1 $Y &Z &3 &K NTHL080N120SC1 = ON Semiconductor Logo = Assembly Plant Code = Data Code (Year & Week) = Lot = Specific Device Code ORDERING INFORMATION See detailed ordering and shipping information on page 2 of this data sheet. Publication Order Number: NTHL080N120SC1/D NTHL080N120SC1 ELECTRICAL CHARACTERISTICS Parameter Symbol Test Conditions Min Typ Max Unit Drain−to−Source Breakdown Voltage V(BR)DSS VGS = 0 V, ID = 1 mA 1200 − − V Drain−to−Source Breakdown Voltage Temperature Coefficient V(BR)DSS/TJ ID = 1 mA, referenced to 25_C − 700 − mV/_C IDSS VGS = 0 V, VDS = 1200 V, TJ = 25_C − − 100 mA VGS = 0 V, VDS = 1200 V, TJ = 175_C − − 1 mA IGSS VGS = +25/−15 V, VDS = 0 V − − ±1 mA Gate Threshold Voltage VGS(th) VGS = VDS, ID = 5 mA 1.8 2.7 4.3 V Recommended Gate Voltage VGOP −5 − +20 V VGS = 20 V, ID = 20 A, TJ = 25_C − 80 110 mW VGS = 20 V, ID = 20 A, TJ = 150_C − 114 − VDS = 20 V, ID = 20 A − 13 − S VGS = 0 V, f = 1 MHz, VDS = 800 V − 1112 − pF OFF CHARACTERISTICS Zero Gate Voltage Drain Current Gate−to−Source Leakage Current ON CHARACTERISTICS Drain−to−Source On Resistance Forward Transconductance RDS(on) gFS CHARGES, CAPACITANCES & GATE RESISTANCE Input Capacitance CISS Output Capacitance COSS − 80 − Reverse Transfer Capacitance CRSS − 6.5 − Total Gate Charge QG(tot) − 56 − − 11 − Gate−to−Source Charge QGS Gate−to−Drain Charge QGD Gate Resistance VGS = −5/20 V, VDS = 600 V, ID = 20 A nC − 12 − RG f = 1 MHz − 1.7 − W td(on) VGS = −5/20 V, VDS = 800 V, ID = 20 A, RG = 4.7 W, Inductive Load − 13 − ns − 20 − td(off) − 22 − SWITCHING CHARACTERISTICS Turn-On Delay Time Rise Time Turn−Off Delay Time tr Fall Time tf − 10 − Turn-On Switching Loss EON − 258 − Turn-Off Switching Loss EOFF − 52 − Total Switching Loss ETOT − 311 − mJ DRAIN−SOURCE DIODE CHARACTERISTICS Continuous Drain−to−Source Diode Forward Current ISD VGS = −5 V, TJ = 25_C − − 18 A Pulsed Drain−to−Source Diode Forward Current (Note 2) ISDM VGS = −5 V, TJ = 25_C − − 132 A Forward Diode Voltage VSD VGS = −5 V, ISD = 10 A, TJ = 25_C − 4 − V Reverse Recovery Time tRR − 16 − ns Reverse Recovery Charge QRR VGS = −5/20 V, ISD = 20 A, dIS/dt = 1000 A/ms − 62 − nC Reverse Recovery Energy EREC − 5 − mJ Peak Reverse Recovery Current IRRM − 8 − A Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. www.onsemi.com 2 NTHL080N120SC1 ID, DRAIN CURRENT (A) 70 NORMALIZED DRAIN TO SOURCE ON−RESISTANCE TYPICAL CHARACTERISTICS TJ = 25°C unless otherwise noted VGS = 20 V VGS = 15 V VGS = 19 V 56 VGS = 16 V VGS = 18 V VGS = 17 V 42 PULSE DURATION = 80 m s DUTY CYCLE = 0.5% MAX 28 VGS = 10 V 14 VGS = 8 V 0 0 4 8 12 16 20 8 VGS = 8 V 6 VGS = 10 V 4 2 0 VGS = 15 V VGS = 16 V 10 20 SOURCE ON-RESISTANCE (m W) 1.4 1.2 1.0 0.8 100 IS, REVERSE DRAIN CURRENT (A) ID, DRAIN CURRENT (A) 8 TJ = 175 oC oC 14 TJ = −55 oC 9 12 10 12 14 16 18 20 Figure 4. On−Resistance vs. Gate−to−Source Voltage VDS = 20 V 6 TJ = 25 oC VGS, GATE TO SOURCE VOLTAGE (V) PULSE DURATION = 80 ms DUTY CYCLE = 0.5% MAX 3 TJ = 150 oC 90 0 70 0 70 ID = 20 A 180 Figure 3. Normalized On Resistance vs. Junction Temperature TJ = 25 60 270 0.6 −75 −50 −25 0 25 50 75 100 125 150 175 TJ, JUNCTION TEMPERATURE (oC) 28 50 PULSE DURATION = 80 ms DUTY CYCLE = 0.5% MAX 360 1.6 rDS(on), DRAIN TO NORMALIZED DRAIN TO SOURCE ON−RESISTANCE 450 ID = 20 A VGS = 20 V 42 40 Figure 2. Normalized On−Resistance vs. Drain Current and Gate Voltage 2.0 0 30 ID, DRAIN CURRENT (A) Figure 1. On Region Characteristics 56 VGS = 18 V VGS = 17 V VGS = 19 V VGS = 20 V 0 VDS, DRAIN TO SOURCE VOLTAGE (V) 1.8 PULSE DURATION = 80 m s DUTY CYCLE = 0.5% MAX TJ = 150 oC TJ = 25 o C 10 TJ = −55 oC 1 0.1 15 VGS = 0 V VGS, GATE TO SOURCE VOLTAGE (V) 0 2 4 6 8 VSD, BODY DIODE FORWARD VOLTAGE (V) Figure 5. Transfer Characteristics Figure 6. Source−to−Drain Diode Forward Voltage vs. Source Current www.onsemi.com 3 NTHL080N120SC1 TYPICAL CHARACTERISTICS TJ = 25°C unless otherwise noted 10000 ID = 20 A Ciss VDD = 400 V 15 CAPACITANCE (pF) VGS, GATE TO SOURCE VOLTAGE (V) 20 VDD = 600 V VDD = 800 V 10 5 0 1000 Coss 100 Crss 10 f = 1 MHz VGS = 0 V 0 10 20 30 40 50 1 0.1 60 Figure 7. Gate Charge Characteristics 100 800 40 RqJC = 0.84 o C/W ID, DRAIN CURRENT (A) IAS, AVALANCHE CURRENT (A) 10 Figure 8. Capacitance vs. Drain−to−Source Voltage 30 TJ = 25 o C 10 TJ = 150 oC 1 0.001 0.01 0.1 1 30 VGS = 20 V 20 10 0 10 25 tAV, TIME IN AVALANCHE (ms) 75 100 125 150 175 Figure 10. Maximum Continuous Drain Current vs. Case Temperature 1000 P(PK), PEAK TRANSIENT POWER (W) 50000 100 10 m s 10 THIS AREA IS LIMITED BY rDS(on) 1 100 m s SINGLE PULSE TJ = MAX RATED 0.1 0.01 50 TC, CASE TEMPERATURE ( o C) Figure 9. Unclamped Inductive Switching Capability ID, DRAIN CURRENT (A) 1 VDS, DRAIN TO SOURCE VOLTAGE (V) Qg, GATE CHARGE (nC) 1 ms 10 ms RqJC = 0.84 oC/W 100 ms TC = 25 oC 0.1 1 10 100 1000 5000 SINGLE PULSE RqJC = 0.84 oC/W TC = 25 oC 10000 1000 100 0.00001 0.0001 0.001 0.01 0.1 t, PULSE WIDTH (sec) VDS, DRAIN to SOURCE VOLTAGE (V) Figure 11. Forward Bias Safe Operating Area Figure 12. Single Pulse Maximum Power Dissipation www.onsemi.com 4 NTHL080N120SC1 r(t), NORMALIZED EFFECTIVE TRANSIENT THERMAL RESISTANCE TYPICAL CHARACTERISTICS TJ = 25°C unless otherwise noted 2 DUTY CYCLE−DESCENDING ORDER 1 D = 0.5 0.2 0.1 0.05 0.02 0.01 0.1 PDM t1 t2 NOTES: 0.01 ZqJC(t) = r(t) x RqJC RqJC = 0.84 oC/W Peak TJ = PDM x ZqJC(t) + TC Duty Cycle, D = t1 / t2 SINGLE PULSE 0.001 0.00001 0.0001 0.001 0.01 0.1 t, RECTANGULAR PULSE DURATION (sec) Figure 13. Junction−to−Case Transient Thermal Response Curve PACKAGE MARKING AND ORDERING INFORMATION Part Number Top Marking Package Packing Method Reel Size Tape Width Quantity NTHL080N120SC1 NTHL080N120SC1 TO−247 Long Lead Tube N/A N/A 30 Units www.onsemi.com 5 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS TO−247−3LD CASE 340CX ISSUE A DATE 06 JUL 2020 GENERIC MARKING DIAGRAM* XXXXXXXXX AYWWG DOCUMENT NUMBER: DESCRIPTION: XXXXX A Y WW G = Specific Device Code = Assembly Location = Year = Work Week = Pb−Free Package *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “ G”, may or may not be present. Some products may not follow the Generic Marking. 98AON93302G TO−247−3LD Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2018 www.onsemi.com onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative