3Northway Lane North Latham,New York 12110.
Tollfree:1.800.984.5337 Phone:1.518.956.2980 Fax:1.518.785.4725 Http://www.marktechopto.com
SPECIFICATION
PART NO. : MT5470-BL 5.2×4.6mm OVAL LED LAMP
ATTENTION
OBSERVE PRECAUTION FOR HANDLING ELECTRO STATIC SENSITIVE DEVICES
MT5470-BL
Description
5.2×4.6mm OVAL LED LAMP
This blue lamp is made with InGaN/Sapphire chip and blue diffused epoxy resin.
4.6 0.5 MAX.
5.2
2.54±0.1
A
1.5 TYP.
K
Notes: 1. All dimensions are in mm. 2. Tolerance is ± 0.25mm unless otherwise noted.
Description
LED Chip Part No.
Material InGaN/Sapphire Emitting Color Blue
24.0 MIN.
7.8
Lens Color
MT5470-BL
Blue diffused
VER.: 01 Date: 2007/03/22 Page: 1/5
MT5470-BL
Absolute Maximum Ratings at Ta=25℃
Parameter
Power Dissipation Reverse Voltage D.C. Forward Current Reverse (Leakage) Current Peak Current(1/10Duty Cycle,0.1ms Pulse Width.) Operating Temperature Range Storage Temperature Range Soldering Temperature(1.6mm from body) Electrostatic discharge
5.2×4.6mm OVAL LED LAMP
Symbol
PD VR If Ir If(Peak) Topr. Tstg. Tsol. ESD.
Rating
100 5 25 50 100 -40 to +95 -40 to +100
Unit
mW V mA μA mA ℃ ℃
Dip Soldering : 260℃ for 5 sec. Hand Soldering : 350℃ for 3 sec. 6000 V
Electrical and Optical Characteristics:
Parameter
Luminous Intensity Forward Voltage Dominant Wavelength Reverse (Leakage) Current Vertical ViewingAngle Horizontal Spectrum Line Halfwidth 2θ1/2 If=20Ma If=20Ma 55 26 nm
Symbol
IV Vf λd Ir 2θ1/2
Condition
If=20mA If=20Ma If=20Ma Vr=5V If=20Ma
Min.
550
Typ.
950 3.2
Max.
Unit
mcd
4.0 475 50
V nm µA
465
470
35 deg
∆λ
Notes: 1. The datas tested by IS tester. 2. Customer’s special requirements are also welcome.
VER.: 01 Date: 2007/03/22 Page: 2/5
MT5470-BL
5.2×4.6mm OVAL LED LAMP
Typical Electrical / Optical Characteristics Curves :
Forward Current IF(mA)
40 30 20 10
Relative Luminous Intensity(mcd)
2.6 3.0 3.4 3.8 4.2
50
1500 1200 900 600 300 20.0
2.2
0.0
10.0
30.0
Applied Voltage (V) FORWARD CURRENT VS.APPLIED VOLTAGE
Forward Current (Ma)
FORWARD CURRENT VS. LUMINOUS INTENSITY
50 40
R j-pin=260℃/W
HORIZONTAL
0°
10°
20° 30°
VERTICAL
Forward Current IF(mA)
30
40° 1.0 50° 60° 70° 80° 90° 0.5 0.3 0.1 0.2 0.4 0.6
20 10
R j-a=490 ℃/W
0.9 0.8
0
20 40 60 Temperature (℃)
80
100
0.7
FORWARD CURRENT VS. AMBIENT TEMPERATURE
RADIATION DIAGRAM
VER.: 01 Date: 2007/03/22 Page: 3/5
MT5470-BL
Specifications for Bin Grading: Iv(mcd) BIN R S T MIN. 550 770 1100
5.2×4.6mm OVAL LED LAMP
MAX. 770 1100 1520
Specifications for Vf Group: Vf(V) Group V6 V7 V8 V9 V10 V11 V12 MIN. 2.6 2.8 3.0 3.2 3.4 3.6 3.8 MAX. 2.8 3.0 3.2 3.4 3.6 3.8 4.0
*Majority VF bins are highlighted in Yellow.
Specifications for Wavelength Group: λD(nm) @20mA Group X4 X5 MIN. 465 470 MAX. 470 475
VER.: 01 Date: 2007/03/22 Page: 4/5
MT5470-BL
5.2×4.6mm OVAL LED LAMP
Precautions:
TAKE NOTE OF THE FOLLOWING IN USE OF LED 1. Temperature in use Since the light generated inside the LED needs to be emitted to outside efficiently, a resin with high light transparency is used; therefore, additives to improve the heat resistance or moisture resistance (silica gel , etc) which are used for semiconductor products such as transistors cannot be added to the resin. Consequently, the heat resistant ability of the resin used for LED is usually low; therefore, please be careful on the following during use. Avoid applying external force, stress, and excessive vibration to the resins and terminals at high temperature. The glass transition temperature of epoxy resin used for the LED is approximately 120-130℃. At a temperature exceeding this limit, the coefficient of liner expansion of the resin doubles or more compared to that at normal temperature and the resin is softened. If external force or stress is applied at that time, it may cause a wire rupture. 2. Soldering Please be careful on the following at soldering. After soldering, avoided applying external force, stress, and excessive vibration until the products go to cooling process (normal temperature), (1) (2) (3) 3. 4. Soldering measurements: Distance between melted solder side to bottom of resin shall be 1.6mm or longer. Solder dip: Preheat: 90℃ max. (Backside of PCB), Within 60 seconds Solder bath: 260±5℃ (Solder temperature), Within 5 seconds Soldering iron : 350℃ max. (Temperature of soldering iron tip), Within 3 seconds
Insertion Pitch of the LED leads and pitch of mounting holes need to be same Others Since the heat resistant ability of the LED resin is low, SMD components are used on the same PCB, please mount the LED after adhesive baking process for SMD components. In case adhesive baking is done after LED lamp insertion due to a production process reason, make sure not to apply external force, stress, and excessive vibration to the LED and follow the conditions below. Baking temperature: 120℃ max. Baking time: Within 60 seconds If soldering is done sequentially after the adhesive baking, please perform the soldering after cooling down the LED to normal temperature.
VER.: 01 Date: 2007/03/22 Page: 5/5
很抱歉,暂时无法提供与“MT5470-BL”相匹配的价格&库存,您可以联系我们找货
免费人工找货