STB6NK60Z-1

STB6NK60Z - STB6NK60Z-1 STP6NK60ZFP - STP6NK60Z N-channel 600 V - 1 Ω - 6 A - TO-220/TO-220FP/D2PAK/I2PAK Zener-Protected SuperMESH™ Power MOSFET Features Type VDSS RDS(on) ID PW STB6NK60Z 600 V < 1.2 Ω 6A 110 W STB6NK60Z-1 600 V < 1.2 Ω 6A 110 W STP6NK60ZFP 600 V < 1.2 Ω 6A 30 W STP6NK60Z 600 V < 1.2 Ω 6A 110 W ■ Extremely high dv/dt capability ■ 100% avalanche tested ■ 3 1 2 3 1 D²PAK TO-220 3 3 12 Gate charge minimized I²PAK 1 2 TO-220FP Application ■ Switching applications Figure 1. Internal schematic diagram Description The SuperMESH™ series is obtained through an extreme optimization of ST’s well established strip-based PowerMESH™ layout. In addition to pushing on-resistance significantly down, special care is taken to ensure a very good dv/dt capability for the most demanding applications. Table 1. Device summary Order codes Marking Package Packaging STB6NK60Z B6NK60Z D²PAK Tape & reel STB6NK60Z-1 B6NK60Z I²PAK Tube STP6NK60ZFP P6NK60ZFP TO-220FP Tube STP6NK60Z P6NK60Z TO-220 Tube November 2007 Rev 8 1/17 www.st.com 17 Contents STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 Electrical characteristics (curves) ............................ 6 3 Test circuit 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5 Packing mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2/17 ................................................ 9 STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z 1 Electrical ratings Electrical ratings Table 2. Absolute maximum ratings Value Symbol Parameter Unit TO-220/D²/I²PAK TO-220FP VDS Drain-source voltage (VGS = 0) 600 V VGS Gate-source voltage ± 30 V ID Drain current (continuous) at TC = 25 °C 6 6 (1) A ID Drain current (continuous) at TC = 100 °C 3.8 3.8 (1) A IDM (2) Drain current (pulsed) 24 24 (1) A PTOT Total dissipation at TC = 25 °C 110 30 W Derating factor 0.88 0.24 W/°C VESD(G-S) G-S ESD (HBM C=100 pF, R=1.5 kΩ) dv/dt(3) Peak diode recovery voltage slope VISO Insulation withstand voltage (DC) Tj Tstg Operating junction temperature Storage temperature 3500 V 4.5 V/ns -- 2500 -55 to 150 V °C 1. Limited only by maximum temperature allowed 2. Pulse width limited by safe operating area 3. ISD ≤ 6 A, di/dt ≤ 200 A/µs, VDD = 80% V(BR)DSS Table 3. Thermal data Value Symbol Parameter Unit TO-220/D²/I²PAK TO-220FP Rthj-case Thermal resistance junction-case max Rthj-amb Thermal resistance junction-amb max Tl Table 4. Symbol Maximum lead temperature for soldering purpose 1.14 4.2 °C/W 62.5 °C/W 300 °C Value Unit 6 A 210 mJ Avalanche characteristics Parameter IAR Avalanche current, repetitive or not-repetitive (pulse width limited by Tj max) EAS Single pulse avalanche energy (starting TJ= 25 °C, ID= IAR, VDD= 50 V) 3/17 Electrical characteristics 2 STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z Electrical characteristics (TCASE=25°C unless otherwise specified) Table 5. On/off states Symbol Parameter V(BR)DSS Drain-source breakdown voltage IDSS Zero gate voltage drain current (VGS = 0) IGSS Test conditions ID = 1 mA, VGS = 0 Min. Typ. Max. Unit 600 V VDS = Max rating VDS = Max rating, TC = 125 °C 1 50 µA µA Gate-body leakage current (VDS = 0) VGS = ± 20 V ±10 µA VGS(th) Gate threshold voltage VDS = VGS, ID = 100 µA 3.75 4.5 V RDS(on) Static drain-source on resistance VGS = 10 V, ID = 3 A 1 1.2 Ω Typ. Max. Unit Table 6. Symbol gfs (1) Ciss Coss Crss Dynamic Parameter Forward transconductance Input capacitance Output capacitance Reverse transfer capacitance Coss eq(2). Equivalent output capacitance Qg Qgs Qgd 3 Total gate charge Gate-source charge Gate-drain charge Test conditions VDS = 8 V, ID = 3 A VDS = 25 V, f = 1 MHz, VGS = 0 Min. 5 56 VDD = 480 V, ID = 6 A, 33 6 17 (see Figure 18) pF pF pF 905 115 25 VGS = 0, VDS = 0 to 480 V VGS = 10 V S pF 46 nC nC nC 1. Pulsed: pulse duration=300µs, duty cycle 1.5% 2. Coss eq. is defined as a constant equivalent capacitance giving the same charging time as Coss when VDS increases from 0 to 80% VDSS 4/17 STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z Table 7. Symbol td(on) tr td(off) tf Table 8. Symbol Electrical characteristics Switching times Parameter Turn-on delay time Rise time Turn-off delay time Fall time Test conditions Min. Typ. Max. 14 14 47 19 VDD = 300 V, ID = 3 A RG = 4.7 Ω VGS = 10 V (see Figure 17) Unit ns ns ns ns Source drain diode Max Unit Source-drain current 6 A ISDM(1) Source-drain current (pulsed) 24 A VSD(2) Forward on voltage ISD = 6 A, VGS = 0 1.6 V Reverse recovery time Reverse recovery charge Reverse recovery current VDD = 50 V, Tj = 150 °C ISD trr Qrr IRRM Parameter Test conditions Min ISD = 6 A, di/dt = 100 A/µs Typ. 445 2.7 12 (see Figure 19) ns µC A 1. Pulse width limited by safe operating area 2. Pulsed: pulse duration= 300 µs, duty cycle 1.5% Table 9. Symbol BVGSO(1) Gate-source zener diode Parameter Gate-source breakdown voltage Test conditions Min. Eggs± 1 mA (open drain) 30 Typ. Max. Unit V 1. The built-in back-to-back Zener diodes have specifically been designed to enhance not only the device’s ESD capability, but also to make them safely absorb possible voltage transients that may occasionally be applied from gate to source. In this respect the Zener voltage is appropriate to achieve an efficient and cost-effective intervention to protect the device’s integrity. These integrated Zener diodes thus avoid the usage of external components. 5/17 Electrical characteristics STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z 2.1 Electrical characteristics (curves) Figure 2. Safe operating area for TO-220/ I²PAK/ D²PAK Figure 3. Thermal impedance for TO-220/ I²PAK/ D²PAK Figure 4. Safe operating area for TO-220FP Figure 5. Thermal impedance for TO-220FP Figure 6. Output characteristics Figure 7. Transfer characteristics 6/17 STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z Figure 8. Transconductance Figure 9. Electrical characteristics Static drain-source on resistance Figure 10. Gate charge vs gate-source voltage Figure 11. Capacitance variations Figure 12. Normalized gate threshold voltage vs temperature Figure 13. Normalized on resistance vs temperature 7/17 Electrical characteristics STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z Figure 14. Source-drain diode forward characteristics Figure 16. Maximum avalanche energy vs temperature 8/17 Figure 15. Normalized BVDSS vs temperature STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z 3 Test circuit Test circuit Figure 17. Switching times test circuit for resistive load Figure 18. Gate charge test circuit Figure 19. Test circuit for inductive load Figure 20. Unclamped Inductive load test switching and diode recovery times circuit Figure 21. Unclamped inductive waveform Figure 22. Switching time waveform 9/17 Package mechanical data 4 STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 10/17 STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z Package mechanical data TO-220 mechanical data mm inch Dim Min A b b1 c D D1 E e e1 F H1 J1 L L1 L20 L30 ∅P Q Typ 4.40 0.61 1.14 0.49 15.25 Max Min 4.60 0.88 1.70 0.70 15.75 0.173 0.024 0.044 0.019 0.6 10.40 2.70 5.15 1.32 6.60 2.72 14 3.93 0.393 0.094 0.194 0.048 0.244 0.094 0.511 0.137 1.27 10 2.40 4.95 1.23 6.20 2.40 13 3.50 Max 0.181 0.034 0.066 0.027 0.62 0.050 16.40 28.90 3.75 2.65 Typ 0.409 0.106 0.202 0.051 0.256 0.107 0.551 0.154 0.645 1.137 3.85 2.95 0.147 0.104 0.151 0.116 11/17 Package mechanical data STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z TO-220FP MECHANICAL DATA mm. DIM. MIN. A 4.4 inch TYP MAX. MIN. TYP. 4.6 0.173 0.181 MAX. 0.106 B 2.5 2.7 0.098 D 2.5 2.75 0.098 0.108 E 0.45 0.7 0.017 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.7 0.045 0.067 F2 1.15 1.7 0.045 0.067 G 4.95 5.2 0.195 0.204 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 L2 16 0.630 L3 28.6 30.6 1.126 1.204 L4 9.8 10.6 .0385 0.417 L5 2.9 3.6 0.114 0.141 L6 15.9 16.4 0.626 0.645 9 9.3 0.354 0.366 Ø 3 3.2 0.118 0.126 B D A E L7 L3 L6 F2 H G G1 F F1 L7 L2 12/17 L5 1 2 3 L4 STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z Package mechanical data TO-262 (I2PAK) MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 A1 2.40 2.72 0.094 0.107 b 0.61 0.88 0.024 0.034 b1 1.14 1.70 0.044 0.066 c 0.49 0.70 0.019 0.027 c2 1.23 1.32 0.048 0.052 D 8.95 9.35 0.352 0.368 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.194 0.202 E 10 10.40 0.393 0.410 L 13 14 0.511 0.551 L1 3.50 3.93 0.137 0.154 L2 1.27 1.40 0.050 0.055 13/17 Package mechanical data STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z D2PAK MECHANICAL DATA TO-247 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 4.4 4.6 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.7 0.93 0.027 0.036 B2 1.14 1.7 0.044 0.067 C 0.45 0.6 0.017 0.023 C2 1.23 1.36 0.048 0.053 D 8.95 9.35 0.352 0.368 D1 E 8 10 E1 0.315 10.4 0.393 8.5 0.334 G 4.88 5.28 0.192 0.208 L 15 15.85 0.590 0.625 L2 1.27 1.4 0.050 0.055 L3 1.4 1.75 0.055 0.068 M 2.4 3.2 0.094 0.126 R 0º 0.015 4º 3 V2 0.4 1 14/17 STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z 5 Packing mechanical data Packing mechanical data D2PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA DIM. mm inch MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 B0 15.7 15.9 0.618 0.626 D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 F 11.4 11.6 0.449 0.456 K0 4.8 5.0 0.189 0.197 P0 3.9 4.1 0.153 0.161 P1 11.9 12.1 0.468 0.476 P2 1.9 2.1 0.075 0.082 inch MAX. MIN. MAX. 330 12.992 13.2 0.504 0.520 26.4 0.960 1.039 0.059 0795 3.937 30.4 1.197 BASE QTY BULK QTY 1000 1000 MAX. R 50 1.574 T 0.25 0.35 0.0098 0.0137 W 23.7 24.3 0.933 0.956 * on sales type 15/17 Revision history 6 STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z Revision history Table 10. 16/17 Document revision history Date Revision Changes 14-Jan-2004 4 Initial electronic version 23-Aug-2005 5 Inserted ecopack label 04-Oct-2005 6 Modified header 23-May-2007 7 Added Figure 16: Maximum avalanche energy vs temperature 22-Nov-2007 8 Figure 11: Capacitance variations has been updated STB6NK60Z - STB6NK60Z-1 - STP6NK60ZFP - STP6NK60Z Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 17/17