STTH506B

STTH506 Turbo 2 ultrafast high voltage rectifier Datasheet - production data Description The STTH506 is developed using ST’s Turbo 2 600 V technology. It is well-suited for use in switching power supplies and industrial applications. . $ . Table 1. Device summary $ 72$& . . . Value IF(AV) 5A VRRM 600 V trr (max) 30 ns Tj (max) 175 °C VF (typ) 1.1 V $ $ 1& Symbol '3$. 1& Features  Ultrafast switching  Low reverse current  Low thermal resistance  Reduces conduction and switching losses  ECOPACK®2 compliant component for DPAK on demand November 2016 This is information on a product in full production. DocID12380 Rev 4 1/11 www.st.com Characteristics 1 STTH506 Characteristics Table 2. Absolute ratings (limiting values at 25° C, unless otherwise specified) Symbol Parameter VRRM Repetitive peak reverse voltage IF(RMS) RMS forward current IF(AV) Average forward current,  = 0.5, square wave. Tc = 145° C IFSM Surge non repetitive forward current tp = 10 ms Sinusoidal Tstg Storage temperature range Tj Value Unit 600 V TO-220AC 20 A DPAK 10 A TO-220AC DPAK 5 A TO-220AC 70 A DPAK 55 A -65 to +175 °C 175 °C Maximum operating junction temperature Table 3. Thermal parameters Symbol Parameter Rth(j-c) Max. value Unit 3.5 ° C/W Junction to case Table 4. Static electrical characteristics Symbol Parameter Test conditions IR(1) Reverse leakage current VF(2) Forward voltage drop Tj = 25° C Tj = 150° C Tj = 25° C Tj = 150° C VR = VRRM IF = 5 A 1. Pulse test: tp = 5 ms,  < 2% 2. Pulse test: tp = 380 µs,  < 2% To evaluate the conduction losses, use the following equation: P = 1.07 x IF(AV) + 0.066 x IF2(RMS) 2/11 DocID12380 Rev 4 Min. Typ - 5 13 - Max. 130 1.85 1.10 1.40 Unit µA V STTH506 Characteristics Table 5. Dynamic characteristics Symbol trr IRM Parameter Test conditions Reverse recovery time Tj = 25° C Qrr Reverse recovery charges tfr Forward recovery time VFP Forward recovery voltage IF = 0.5 A Irr = 0.25 A IR = 1 A - IF = 1 A VR = 30 V dIF/dt = -50 A/µs - 35 50 - 3.5 5 - 175 Tj = 125° C IF = 5 A VR = 400 V dIF/dt = -100 A/µs Tj = 25° C IF = 5 A VFR = 1.1 x VFmax dIF/dt = 100 A/µs Reverse recovery current DocID12380 Rev 4 Min. Typ Max. Unit 30 ns - nC 180 4 A ns V 3/11 11 Characteristics STTH506 Figure 1. Conduction losses versus average current  3)$9 : į  į   į  Figure 2. Forward voltage drop versus forward current  į  ,)$  7 M ƒ&  į   PD[LPXPYDOXHV    7 M  ƒ&  W\LFDOYDOXHV    PD[LPXPYDOXHV   7   į WS7  7 M ƒ&          ,)$9 $ WS      = 5  WKMF WKMF           Figure 4. Peak reverse recovery current versus dIF/dt (typical values) ,50$  72$& '3$. 6LQJOHSXOVH  9)9  Figure 3. Relative variation of thermal impedance junction to case versus pulse duration   95 9 7M ƒ&  ,) [,)$9      ,) ,)$9  ,) [,)$9      ,) [,)$9      W3V  ( GO)GW$—V  ( ( ( Figure 5. Reverse recovery time versus dIF/dt (typical values)  WUUQV  ,) [,)$9     95 9 7M ƒ& ,) [,)$9      ,) ,)$9    ,) [,)$9     GO)GW$—V GO)GW$—V   4/11  ,) [,)$9   ,) ,)$9   4UUQ&    Figure 6. Reverse recovery charges versus dIF/dt (typical values)  95 9 7M ƒ&              DocID12380 Rev 4           STTH506 Characteristics Figure 7. Softness factor versus dIF/dt (typical values) Figure 8. Relative variations of dynamic parameters versus junction temperature 6IDFWRU  ,) [,)$9 95 9 7M ƒ&   ,) ,)$9 95 9 5HIHUHQFH7M ƒ&      6IDFWRUDQG,   50  4 UU    7 ƒ& GO)GW$—V M                   Figure 9. Transient peak forward voltage versus Figure 10. Forward recovery time versus dIF/dt dIF/dt (typical values) (typical values) 9)39    ,) ,)$9 7M ƒ& ,) ,)$9 9)5 [9)PD[ 7M ƒ&                    WIUQV    GO)GW$—V GO)GW$—V       Figure 11. Junction capacitance versus reverse voltage applied (typical values) &S)    ) 0+] 926& P9506 7  ƒ& M      Figure 12. Thermal resistance junction to ambient versus copper surface under tab  5WKMDƒ&: (SR[\SULQWHGERDUG)5FRSSHUWKLFNQHVV —P   '3$.          959    6 FPð &8     DocID12380 Rev 4         5/11 11 Package Information 2 STTH506 Package Information  Epoxy meets UL94, V0  Cooling method: by conduction (C)  Recommended torque value: 0.55 Nm for TO-220AC  Maximum torque value: 0.7 Nm for TO-220AC In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 2.1 DPAK package information Figure 13. DPAK package outline ( $ E F 7KHUPDOSDG ( / ' ' 5 + / $ E H H 5 F $ / /  Note: 6/11 9 *DXJH SODQH This package drawing may slightly differ from the physical package. However, all the specified dimensions are guaranteed. DocID12380 Rev 4 STTH506 Package Information Table 6. DPAK package mechanical data Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A 2.18 2.40 0.085 0.094 A1 0.90 1.10 0.035 0.043 A2 0.03 0.23 0.001 0.009 b 0.64 0.90 0.025 0.035 b4 4.95 5.46 0.194 0.214 c 0.46 0.61 0.018 0.024 c2 0.46 0.60 0.018 0.023 D 5.97 6.22 0.235 0.244 D1 4.95 5.60 0.194 0.220 E 6.35 6.73 0.250 0.264 E1 4.32 5.50 0.170 0.216 e 2.28 0.090 e1 4.40 4.70 0.173 0.185 H 9.35 10.40 0.368 0.409 L 1.00 1.78 0.039 0.070 L2 1.27 0.050 L4 0.60 1.02 0.023 0.040 V2 -8° +8° -8° 8° Figure 14. Footprint (dimensions in mm)      % 7KHGHYLFHPXVWEHSRVLWLRQHGZLWKLQ DocID12380 Rev 4 $   $ % 7/11 11 Package Information 2.2 STTH506 TO-220AC package information Figure 15. TO-220AC package outline $ + ‘, & / / / / ) ' / / ) 0 ( * 8/11 DocID12380 Rev 4 STTH506 Package Information Table 7. TO-220AC package mechanical data Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A 4.40 4.60 0.173 0.181 C 1.23 1.32 0.048 0.051 D 2.40 2.72 0.094 0.107 E 0.49 0.70 0.019 0.027 F 0.61 0.88 0.024 0.034 F1 1.14 1.70 0.044 0.066 G 4.95 5.15 0.194 0.202 H2 10.00 10.40 0.393 0.409 L2 16.40 typ. 0.645 typ. L4 13.00 14.00 0.511 0.551 L5 2.65 2.95 0.104 0.116 L6 15.25 15.75 0.600 0.620 L7 6.20 6.60 0.244 0.259 L9 3.50 3.93 0.137 0.154 M Diam. I 2.6 typ. 3.75 0.102 typ. 3.85 DocID12380 Rev 4 0.147 0.151 9/11 11 Ordering Information 3 STTH506 Ordering Information Table 8. Ordering information 4 Order code Marking Package Weight Base qty Delivery mode STTH506B-TR STTH 506B DPAK 0.30 g 2500 Tape and reel STTH506B STTH 506B DPAK 0.30 g 75 Tube STTH506D STTH506D TO-220AC 1.86 g 50 Tube Revision history Table 9. Document revision history 10/11 Date Revision Description of Changes 14-Oct-2008 1 First issue. 08-Aug-2014 2 Updated DPAK package information and removed TO-220AB package. 26-Nov-2014 3 Updated Figure 13 and Figure 14. 03-Nov-2016 4 Updated DPAK package information and reformatted to current standard. DocID12380 Rev 4 STTH506 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved DocID12380 Rev 4 11/11 11