TPD1038F

TPD1038F Toshiba Intelligent Power Device TPD1038F Silicon Monolithic Power MOS Integrated Circuit Motor, Solenoid, Lamp Drivers High-side Power Switch The TPD1038F is a monolithic power IC for high-side switches. The IC has a vertical MOS FET output which can be directly driven from a CMOS or TTL logic circuit (e.g., an MPU). The device offers intelligent self-protection and diagnostic functions. Features • A monolithic power IC with a structure combining a control block (Bi-CMOS) and a vertical power MOS FET on a single chip. One side of load can be grounded to a high-side switch. Can directly drive a power load from a microprocessor. Built-in protection short-circuiting. against overheating and load SOP8-P-1.27A Weight：0.08g(typ.) • • • • • • • Incorporates a diagnosis function that allows diagnosis output to be read externally at load short-circuiting, opening, or overheating. Up to -(50-VDD)～ -(60-VDD) of counterelectromotive force from an L load can be applied. Low on-resistance : RDS(ON)=120mΩ(max) ( @ VDD = 12 V、Ta = 25℃、Io = 2 A) 8-pin SOP package for surface mounting that can be packed in tape Pin Assignment OUT 1 8 VDD Marking GND 2 7 VDD TPD1038 F Part No. (or abbreviation code) Lot No. A line indicates lead (Pb)-free package or lead (Pb)-free finish. DIAG 3 6 VDD IN 4 (TOP VIEW) 5 VDD Due to its MOS structure, this product is sensitive to static electricity. 1 2006-10-31 TPD1038F Block Diagram Bandgap 5V regulator VDD charge pump IN driver MOSFET (π-MOSⅤ) current detection overheat detection DIAG OUT GND Pin Description Pin No. 1 2 3 4 5,6,7,8 Symbol OUT GND DIAG IN VDD Function Output pin. When the load is short-circuited and current in excess of the detection current (3A min) flows to the output pin, the output automatically turns on or off. Ground pin. Self-diagnosis detection pin.Goes low when overheating is detected or when output is short circuit with input on (high). N-channel open drain. Input pin. Input is CMOS compatible, with pull down resistor connected. Even if the input is open, output will not accidentally turn on. Power pin. 2 2006-10-31 TPD1038F Timing Chart Input signal Hysteresis 5℃ (typ.) Tch Channel temperature Overcurrent detection Overheating detection 150℃(min) Load open Output current Output signal Diagnostic output Thermal shutdown Load open detection Current limit Normal Truth Table Input signal H L H L H L H L H L Diagnosis output H L L L L L H H L H Output signal H L L L L L H H L H Output state on off current limit (switching) off off off on off off off Overheating Operating state Normal Load short Load open Overheating and load open 3 2006-10-31 TPD1038F Absolute Maximum Ratings (Ta = 25°C) Characteristics Drain-source voltage Supply voltage DC Pulse DC Pulse Symbol VDS VDD(1) VDD(2) VIN(1) VIN(2) VDIAG IO IIN IDIAG PD(1) PD(2) Topr Tch Tstg Rating 60 25 60(RS=1Ω,τ=250ms) －0.5～12 VDD(1)+1.5(t=100ms) －0.5～25 Internally limited ±10 5 1.1 0.425 －40～110 150 －55～150 Unit V V V V V V A mA mA W W °C °C °C Input voltage Diagnosis output voltage Output current Input current Diagnosis current Power dissipation (Note 1-a) Power dissipation (Note 1-b) Operating temperature Channel temperature Storage temperature Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Thermal Resistance Characteristic Thermal resistance Symbol Rth(ch-a) Rating 113.5 (Note1-a) 294.0 (Note1-b) Unit °C /W Note 1: 1-a : Mounted on glass epoxy board (a) 1-b : Mounted on glass epoxy board (b) FR-4 25.4×25.4×0.8 (Unit：mm) FR-4 25.4×25.4×0.8 (Unit：mm) 4 2006-10-31 TPD1038F Electrical Characteristics (Ta=25°C) Characteristics Operating supply voltage Current dissipation H-level input voltage L-level input voltage H-level input current On resistance Output leakage current Diagnosis output voltage Diagnosis output current “L”-level “H”-level Symbol VDD(OPR) IDD VIH VIL IIH RDS(ON) IOL VDL IDH IOC(1)(Note2) IOC(2)(Note3) TOT Rop ton toff tDLH tDHL Vclamp Test circuit － － － － － － － － － 1､2 3 － － 4 5 － Test condition － VDD=12V, VIN=0V, RL=10Ω VDD=12V VDD=12V VDD=12V, VIN=5V VDD=12V, IO=2A VDD=12V VDD=12V, VIN=0V, IDL=1mA RL=10Ω VDD=12V, VIN=5V, RL=10Ω, VDH=12V VDD=12V VDD=12V, RL=0.1Ω VDD=12V VDD=12V, VIN=0V VDD=12V, RL=10Ω VDD=12V, RL=10Ω VDD=12V, VIN=0V, IO=1A, L=10mH min 6 － 3.5 － － － － － － 3 － 150 5 － － － － -(60VDD) typ. 12 － － － － － － － － － － － 17 － － 70 22 － max 18 3 － 1.5 200 0.12 1 0.4 10 9 10 200 － 100 40 － － -(50VDD) Unit V mA V V μA Ω mA V μA A A ℃ kΩ μs μs μs μs Ｖ Over current detection Overheating detection Load open detection (Note4) Switching time Diagnosis delay time Output clamp voltage (Note 2) Over-current detection (Note 3) Peak current @ current limit function (Note 4) Load open detection function : VDD = 8 ～ 18V Test Circuit 1 Over current detection IOC(1) ：Over current detection when load current is increased while VIN = "H" 5V 2.5kΩ VDIAG OUT DIAG VDD=12V IOC(1) 0 IO RL VDIAG 0V 5V IO TPD1038F 5V VIN ＜0.4V VDL 5 2006-10-31 TPD1038F Test Circuit 2 Over current detection IOC(1) ：Over current detection when load is short circuit and VIN = "L" → "H" 5V 2.5kΩ VDIAG OUT DIAG VDD=12V IOC(1) 0 IO RL VDIAG 0V 5V IO TPD1038F P.G VIN ＜0.4V VDL Test Circuit 3 Over current detection IOC(2) 5V 2.5kΩ VDIAG OUT DIAG VDD=12V VIN TPD1038F IO RL=0.1Ω IO IOC(2) P.G VIN Test Circuit 4 Switching time ton, toff VDD=12V VIN DIAG OUT ≦0.1μs 90% 10% VOUT RL=10Ω VOUT 90% ≦0.1μs 90% 5V 10% ≒12V 10% TPD1038F P.G VIN ton toff Test Circuit 5 Diagnosis delay time tDLH, tDHL 5V 5kΩ VDIAG OUT VDD=12V VIN ≦0.1μs 90% 10% ≦0.1μs 90% 5V 10% 5V RL=10Ω VDIAG 0V tDLH tDHL 50% 50% TPD1038F P.G VIN 6 2006-10-31 TPD1038F 2.5 I - V DD IDD DD – VDD Tch=25°C 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 VDS(ON) I I V DS(ON) - –OO VDD=12V CURRENT DISSIPATION I (mA) CURRENT DISSIPATION IDDDD(mA) 2 LOAD OPEN，VIN=5V 1.5 RL=10Ω，VIN=0V 1 0.5 LOAD OPEN，VIN=0V 0 0 4 8 12 16 20 ON VOLTAGE VDS(ON) ((V) ON VOLTAGE DS(ON) V) Tch=25°C 0 0.5 1 1.5 2 2.5 3 3.5 4 SUPPLY VOLTAGE VDD (V) SUPPLY VOLTAGE DD V) OUTPUT CURRENT IO A) OUTPUT CURRENT IO ((A) RDS(ON) – T RDS(ON) - Tchch 0.2 0.2 RDS(ON) – VDD RDS(ON) - V DD IO=2A ON RESISTANCE RDS(ON) ( Ω) ) ON RESISTANCE RDS(ON) (Ω 0.16 IO=2A ON RESISTANCE RRDS(ON)( Ω(Ω) ON RESISTANCE DS(ON) ) VDD=12V 0.16 Tch=25°C 0.12 0.12 0.08 0.08 0.04 0.04 0 -80 0 -40 0 40 80 120 160 0 4 8 12 16 20 OPERATING TEMPERATURE ch °C) CHANNEL TEMPERATURE Tch ((°C) SSUPPLYVOLTAGE VDD (V) UPPLY VOLTAGE V DD ( V) V - – VDD V IH IH V DD H-LEVEL INPUT VOLTAGE V IH ( V) H-LEVEL INPUT VOLTAGE VIH (V) 5 5 V ILV- V DDDD IL – V Tch=25°C L -LEVEL INPUT VOLTAGE V IL V) L-LEVEL INPUT VOLTAGE VIL ((V) Tch=25°C 4 4 3 3 2 2 1 1 0 0 4 8 12 16 20 0 0 4 8 12 16 20 SUPPLY VOLTAGE VDD (( V) SUPPLY VOLTAGE V DD V) SUPPLY VOLTAGE VDD (V) SUPPLY VOLTAGE DD V) 7 2006-10-31 TPD1038F 12 IOCOC Tch ch I - –T VDD=12V 200 V DLDL Tchch V - –T VDD=12V OVER CURRENT DETECTION IOC OVER CURRENT PROTECTION (A) (A) 10 8 DIAGNOSIS OUTPUT VOLTAGE (mV) IOC(2) VDL 160 120 IDL=2mA 80 IDL=1mA 40 160 0 -80 6 IOC(1) 4 2 0 -80 -40 0 40 80 120 -40 0 40 80 120 160 CHANNEL TEMPERATURE Tch ( °C) OPERATING TEMPERATURE ch °C) CHANNEL TEMPERATURE Tch ( °C) OPERATING TEMPERATURE ch (°C) -80 Vclamp – T V clamp - Tch ch VDD=12V VIN=0V SWITCHING CHARACTERISTICS SWITCHING CHARACTERISTICS 160 RL=10Ω Vclamp OUTPUT CLAMP VOLTAGE (V) -60 IO=1A L=10mH SSWITCHING TIME ((μs) WITCHING TIME μs) Tch=25°C 120 -40 80 tON -20 40 tOFF 0 -80 0 -40 0 40 80 120 160 0 4 8 12 16 20 OPERATING TEMPERATURE Tch (°C) CHANNEL TEMPERATURE Tch (°C) SSUPPLYVOLTAGE VDD (V) UPPLY VOLTAGE V DD V) tDLH T Tch tDLH－– ch 200 40 RL=10Ω 160 tDHL T Tch tDHL - – ch DIAGNOSIS DELAY TIME ttDHL ( μμs) DIAGNOSIS DELAY TIME DHL ( s) RL=10Ω tDLH (μs) 30 VDD=18V VDD=12V DIAGNOSIS DELAY TIME 120 VDD=18V 80 VDD=12V 40 VDD=6V 20 VDD=6V 10 0 -80 -40 0 40 80 120 160 0 -80 -40 0 40 80 120 160 OPERATING TEMPERATURE CHANNEL TEMPERATURE Tch (°C) CHANNEL TEMPERATURE Tch ((°C) °C) OPERATING TEMPERATURE 8 2006-10-31 TPD1038F LOAD OPEN DETECTION ROP (kΩ LOAD OPEN DETECTION ROP ( kΩ) ) 160 tDLH－ V DDVDD ,tDHL – Tch=25°C RL=10Ω 100 RROP – DD OP - V VDD Tch=25°C DIAGNOSIS DELAY TIME DIAGNOSIS DELAY TIME ( μs) tDLH,tDHL (μs) 120 (k op R オ ー プ ン 検 出 抵 80 ROPH:LOAD OPEN DETECTION RESITANCE ROPL:LOAD OPEN DETECTION RESET RESISTANCE tDLH 80 60 ROPH 40 ROPL 20 40 tDHL 0 0 4 8 12 16 20 0 0 4 8 12 16 20 SUPPLY VOLTAGE VDD (V) SUPPLY VOLTAGE V DD (V) SUPPLY VOLTAGE VDD ((V) SUPPLY VOLTAGE V DD V) 電源電圧 V D (V) D ROP T T ROP - –chch LOAD OPEN DETECTION ROP ( kΩ) ) LOAD OPEN DETECTION ROP (kΩ 50 VDD=12V 40 ROPH:LOAD OPEN DETECTION RESITANCE 30 ROPL:LOAD OPEN DETECTION RESET RESISTANCE ROPH 20 1.6 PDP- Ta Ta D– (1)MOUNTED ON GLASS EPOXY BOARD (a) (2)MOUNTED ON GLASS EPOXY BOARD(b) (1) POWER DISSIPATION P ( ( POWER DISSIPATION PD DW) W) 1.2 0.8 (2) 0.4 10 ROPL 0 -80 -40 0 40 80 120 160 0 -40 0 40 80 120 160 COPERATING TEMPERATURE Tch (°C) HANNEL TEMPERATURE Tch ( °C) AMBIENT TEMPERATURE Ta °C) AMBIENT TEMPERATURE Ta ((°C) rth(ch-a) - tW 1000 TRANSIENT THERMAL RESISTANCE (1)MOUNTED ON GLASS EPOXY BOARD(a) (2)MOUNTED ON GLASS EPOXY BOARD(b) SINGLE PULSE,Ta=25℃ (2) 100 r th(ch-a) (°C/W) (1) 10 1 0.1 0.001 0.01 0.1 1 10 100 1000 PULSE WIDTH tw (s) 9 2006-10-31 TPD1038F Package Dimensions Weight: 0.08g (typ.) 10 2006-10-31 TPD1038F RESTRICTIONS ON PRODUCT USE • The information contained herein is subject to change without notice. 20070701-EN • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 11 2006-10-31