NCV5504DTRKG

NCP5504, NCV5504 Linear Regulator - Dual Output, Low Dropout 250 mA The NCP5504/NCV5504 are dual output low dropout linear regulators with ±2.0% accuracy over the operating temperature range. They feature a fixed output voltage of 3.3 V (contact factory for other fixed output voltage options) and an adjustable output that ranges from 1.25 V to 5.0 V. It is available in a 5 pin DPAK Pb−Free package. The NCP5504/NCV5504 employs an architecture that offers low noise without a bypass capacitor for the fixed output. This device along with a ripple rejection of 75 dB and a dropout of 250 mV @ 250 mA, suits post−regulation and power sensitive battery−operated applications. Features • • • • • • • • • • • • • • • One Fixed and One Adjustable Output Pin 250 mA Each Output Adjustable Output Voltage from 1.25 V to 5.0 V Low Dropout Voltage of 250 mV typical at 250 mA Low Quiescent Current of 370 mA typical Ripple Rejection of 75 dB Temperature Range of NCP5504 −25°C to +85°C Temperature Range of NCV5504 −40°C to +125°C Low Noise Without Bypass Capacitor; 90 mVrms Line Regulation < 15 mV Load Regulation; Vout1 < 15 mV, Vout2 < 10 mV Accuracy of ±2% Overtemperature Range Thermal Protection and Current Limit Short Circuit Protection NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable These are Pb−Free Devices http://onsemi.com DPAK−5 DT SUFFIX CASE 175AA MARKING DIAGRAM 5504G ALYWW A L Y WW G Pin 1. Adjust for Vout 2. Vout2 3. GND 4. Vin 5. Vout1 = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet. Typical Applications • • • • • Audio Visual Equipment Battery Powered Consumer Products Instrumentation Computing and Networking Applications Automotive Electronics © Semiconductor Components Industries, LLC, 2013 October, 2019 − Rev. 4 1 Publication Order Number: NCP5504/D NCP5504, NCV5504 PIN FUNCTION DESCRIPTION Pin No. Pin Name 1 Adjust for Vout2 Description This pin is connected to the resistor divider on the output. For a 1.25 V output, connect directly to the Vout2 pin. 2 Vout2 Adjustable Regulated Output Voltage. 3 GND Power Supply Ground 4 Vin 5 Vout1 Positive Power Supply Input Voltage. Fixed Regulated Output Voltage. See selector guide for options. MAXIMUM RATINGS Rating Symbol Value Unit Input Voltage Vin 18 V Operating Input Voltage for Power Considerations Vin 9.0 V Output Pin Voltage Vout −0.3 to Vin +0.3 V Adjust Pin Voltage Vadj −0.3 to Vin +0.3 Maximum Junction Temperature NCP5504 NCV5504 TJ Operating Ambient Temperature NCP5504 NCV5504 TA Package Thermal Resistance Thermal Resistance, Junction−to−Air Thermal Resistance, Junction−to−Case 125 150 −25°C to +85°C −40°C to +125°C V °C °C RqJA RqJC 100 8 °C/W Storage Temperature Range Tstg −55 to +150 °C Electrostatic Discharge Sensitivity Human Body Model (HBM) Machine Model (MM) Charge Device Model (CDM) ESD Latchup Performance (JESD78) Positive Negative ILatchup 2000 200 2000 100 100 V mA Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. http://onsemi.com 2 NCP5504, NCV5504 NCP5504 ELECTRICAL CHARACTERISTICS (Vin = Vout + 1.0 V, where Vout is the larger of Vout1 or Vout2, TA = 25°C, unless otherwise noted) Characteristic Symbol Output Voltage NCP5504 (TA = −25°C to 85°C), IO = 250 mA Min Typ Max Vout Vout1 Vout2 Adjustable Pin Current Unit V −2% −2% 3.30 1.25 +2% +2% Iadj − 50 100 nA Line Regulation (Vout + 1.0 V < Vin < 7.0 V), IO = 250 mA Regline − 5 15 mV Load Regulation (1.0 mA < IO< 250 mA) for Vout1 Load Regulation (1.0 mA < IO < 250 mA) for Vout2 Regload − 10 5 15 10 mV mV VDO − 250 400 mV − − 75 60 − − Dropout Voltage (IO = 250 mA) Ripple Rejection Ratio (IO = 250 mA) RR 120 Hz 1 kHz dB Quiescent Current (IO1, IO2 = 0 mA) Iq − 370 450 mA Fixed Output Noise Voltage (10 Hz − 100 kHz Vout = 3.3 V, IO = 100 mA, CO = 1.0 mF) Vn − 90 − mVrms Ground Current (IO1, IO2 = 250 mA) Ignd − 10 20 mA TJmax 150 165 − °C Ilim 350 450 − mA Thermal Shutdown (Guaranteed by design) Current Limit on Vout1 and Vout2 NCV5504 ELECTRICAL CHARACTERISTICS (Vin = Vout + 1.0 V, where Vout is the larger of Vout1 or Vout2, −40°C ≤ TJ ≤ 150°C, −40°C ≤ TA ≤ 125°C, unless otherwise noted) Symbol Characteristic Output Voltage NCV5504, IO = 250 mA Min Typ Max Vout Vout1 Vout2 Unit V −2% −2% 3.30 1.25 +2% +2% Iadj − 50 100 nA Line Regulation (Vout + 1.0 V < Vin < 7.0 V), IO = 250 mA Regline − 5 15 mV Load Regulation (1.0 mA < IO< 250 mA) for Vout1 Load Regulation (1.0 mA < IO < 250 mA) for Vout2 Regload − 10 5 15 10 mV mV VDO − 250 400 mV − − 75 60 − − Adjustable Pin Current Dropout Voltage (IO = 250 mA) Ripple Rejection Ratio (IO = 250 mA) RR 120 Hz 1 kHz dB Quiescent Current (IO1, IO2 = 0 mA) Iq − 370 450 mA Fixed Output Noise Voltage (10 Hz − 100 kHz Vout = 3.3 V, IO = 100 mA, CO = 1.0 mF) Vn − 90 − mVrms Ground Current (IO1, IO2 = 250 mA) Ignd − 10 20 mA TJmax 150 165 − °C Ilim 320 450 − mA Thermal Shutdown (Guaranteed by design) Current Limit on Vout1 and Vout2 http://onsemi.com 3 NCP5504, NCV5504 NCP5504/ NCV5504 NCP5504/ NCV5504 Adj Vout2 GND Vin Vout1 1 2 3 4 5 Adj Vout2 GND Vin Vout1 1 2 3 4 5 Vout1 Vin Cout2 Cin Vout1 Vin Vout2 Cn Cout1 Vout2 R2 Cout2 Cin Cout1 R1 GND GND Figure 1. Application Schematic, Fixed Output Version. Vout1 = 3.3 V, Vout2 = 1.25 V NOTE: Figure 2. Application Schematic, Adjustable Version. Vout1 = 3.3 V, Vout2 = 1.25 V to 5.0 V, Where Vout2 = 1.25 V * (1+R2/R1) Please note that in order to maintain high accuracy on the adjustable output (Vout2), use R1 values < 30 kW in the resistor divider. The recommended capacitor type and values are as follows: Cin (Tantalum or Aluminum Electrolytic) = 4.7 mF to 100 mF Cout1, Cout2 = Low ESR, 1.0 mF to 22 mF Cn = 200 pF to 1.0 nF. http://onsemi.com 4 NCP5504, NCV5504 TYPICAL CHARACTERISTICS 1.30 Vin = 4.3 V 3.295 Vin = 4.3 V Vout2, OUTPUT VOLTAGE (V) Vout1, OUTPUT VOLTAGE (V) 3.30 3.29 3.285 3.28 3.275 3.27 3.265 3.26 0 50 100 150 200 250 1.28 1.26 1.24 1.22 1.20 0 50 Iout, OUTPUT CURRENT (mA) 200 250 Figure 4. Output Voltage vs. Output Load Current for Vout2 16 300 IO1 = 250 mA IGND, GROUND CURRENT (mA) VDO, DROPOUT VOLTAGE (mV) 150 Iout, OUTPUT CURRENT (mA) Figure 3. Output Voltage vs. Output Load Current for Vout1 250 200 150 100 50 0 −40 100 −20 0 20 40 60 80 100 12 10 8 6 4 2 0 −40 120 IO1 = IO2 = 250 mA 14 −20 0 20 40 60 80 100 TJ, JUNCTION TEMPERATURE (°C) TJ, JUNCTION TEMPERATURE (°C) Figure 5. Dropout Voltage vs. Temperature for Vout1 http://onsemi.com 5 Figure 6. Ground Current vs. Temperature 120 NCP5504, NCV5504 450 450 400 Ilim, SHORT CIRCUIT LIMIT (mA) 500 400 350 300 250 200 150 100 50 RR, RIPPLE REJECTION (dB) 0 −40 −20 0 20 40 60 80 100 350 300 250 200 150 100 50 0 −40 120 90 80 70 60 IO = 10 mA 50 10 0 0.1 40 60 80 100 Figure 8. Short Circuit Current Limit vs. Temperature for Vout2 100 20 20 Figure 7. Short Circuit Current Limit vs. Temperature for Vout1 90 30 0 TJ, JUNCTION TEMPERATURE (°C) 100 40 −20 TJ, JUNCTION TEMPERATURE (°C) RR, RIPPLE REJECTION (dB) Iim, SHORT CIRCUIT LIMIT (A) TYPICAL CHARACTERISTICS Vin = 5.0 V Vout1 = 3.3 V Cin = 4.7 mF Cout = 1.0 mF TJ = 25°C 1.0 IO = 250 mA 10 100 1000 120 80 70 60 IO = 10 mA 50 40 30 20 10 0 0.1 F, FREQUENCY (kHz) Vin = 5.0 V Vout2 = 1.25 V Cin = 4.7 mF Cout = 1.0 mF TJ = 25°C 1.0 IO = 250 mA 10 100 1000 F, FREQUENCY (kHz) Figure 9. Ripple Rejection vs. Frequency for Vout1 Figure 10. Ripple Rejection vs. Frequency for Vout2 http://onsemi.com 6 NCP5504, NCV5504 TYPICAL CHARACTERISTICS 600 Vin = 5.0 V Vout1 = 3.3 V IO = 10 mA Cin = 4.7 mF Cout = 4.7 mF TA = 25°C 500 400 300 200 100 0 START: 100 Hz NOISE DENSITY (nVrms/ǨHz) NOISE DENSITY (nVrms/ǨHz) 600 400 300 200 100 0 STOP: 100 kHz Vin = 5.0 V Vout1 = 3.3 V IO = 250 mA Cin = 4.7 mF Cout = 4.7 mF TA = 25°C 500 START: 100 Hz Figure 11. Noise Density vs. Frequency Figure 12. Noise Density vs. Frequency 250 Vin = 5.0 V Vout2 = 1.25 V IO = 10 mA Cin = 4.7 mF Cout = 4.7 mF TA = 25°C 250 200 150 100 50 START: 100 Hz NOISE DENSITY (nVrms/ǨHz) NOISE DENSITY (nVrms/ǨHz) 300 0 STOP: 100 kHz 200 150 50 0 STOP: 100 kHz Vin = 5.0 V Vout2 = 1.25 V IO = 250 mA Cin = 4.7 mF Cout = 4.7 mF TA = 25°C 100 START: 100 Hz Figure 13. Noise Density vs. Frequency STOP: 100 kHz Figure 14. Noise Density vs. Frequency http://onsemi.com 7 NCP5504, NCV5504 Vout 100 mV/Div IO = 10 mA to 250 mA IO = 1.0 mA to 250 mA TIME (100 mS/Div) Figure 15. Load Transient Response for Vout1 Figure 16. Load Transient Response for Vout1 Vout 50 mV/Div TIME (100 mS/Div) Vin = 5.0 V Vout2 = 1.25 V Cin = 4.7 mF Cout = 4.7 mF TA = 25°C IO = 10 mA to 250 mA IO 100 mA/Div IO 100 mA/Div Vin = 5.0 V Vout1 = 3.3 V Cin = 4.7 mF Cout = 4.7 mF TA = 25°C IO 100 mA/Div Vin = 5.0 V Vout1 = 3.3 V Cin = 4.7 mF Cout = 4.7 mF TA = 25°C Vout 50 mV/Div IO 100 mA/Div Vout 100 mV/Div TYPICAL CHARACTERISTICS TIME (100 mS/Div) IO = 1.0 mA to 250 mA TIME (100 mS/Div) Figure 18. Load Transient Response for Vout2 Vin 1.0 V/Div Vin 1.0 V/Div Figure 17. Load Transient Response for Vout2 DVin = 1.0 V Vout1 = 3.3 V IO = 250 mA Tr = Tf = 1.0 ms Cout = 4.7 mF TA = 25°C Vout 50 mV/Div Vout 50 mV/Div Vin = 5.0 V Vout2 = 1.25 V Cin = 4.7 mF Cout = 4.7 mF TA = 25°C TIME (40 mS/Div) DVin = 1.0 V Vout2 = 1.25 V IO = 250 mA Tr = Tf = 1.0 ms Cout = 4.7 mF TA = 25°C TIME (40 mS/Div) Figure 19. Line Transient Response for Vout1 Figure 20. Line Transient Response for Vout2 http://onsemi.com 8 NCP5504, NCV5504 APPLICATION INFORMATION Introduction will reduce device sensitivity and enhance the output transient response time. The PCB layout is very important and in order to obtain the optimal solution, the Vin and GND traces should be sufficiently wide to minimize noise and unstable operation. For the adjustable output pin, Cn ranges from 200 pF and 1.0 nF. The output capacitor range is between 1.0 mF and 22 mF. For PCB layout considerations, place the capacitor close to the output pin and keep the leads short. The NCP5504/NCV5504 are high performance dual output, 250 mA linear regulators suitable for post regulation and power sensitive battery−operated applications. They feature ±2.0% accuracy over the operating temperature range. With one fixed output voltage at 3.3 V, and one adjustable output voltage ranging from 1.25 V to 5.0 V, the dropout voltage is 250 mV typical. Additional features, such as an architecture that allows for low noise on the fixed output without a bypass capacitor, provides for an attractive LDO solution for audio visual equipment, instrumentation, computing and networking applications, and automotive electronics. It is thermally robust and is offered in a 5 pin DPAK Pb−Free package. Adjustable Output Operation The application circuit for the adjustable output version is shown in Figure 2. Vout2 is calculated based on the following equation: Capacitor Selection ǒ Ǔ Vout2 + 1.25 V * 1 ) R2 R1 The recommended input capacitor types are tantalum and aluminum electrolytic ranging from 4.7 mF to 100 mF. It is especially required if the power source is located more than a few inches from the NCP5504/NCV5504. This capacitor In order to maintain high accuracy on the adjustable output, R1 values should be < 30 kW. ORDERING INFORMATION Package Shipping† NCP5504DTRKG DPAK (Pb−Free) 2500 / Tape and Reel NCV5504DTRKG* DPAK (Pb−Free) 2500 / Tape and Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable http://onsemi.com 9 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS DPAK−5, CENTER LEAD CROP CASE 175AA ISSUE B DATE 15 MAY 2014 SCALE 1:1 −T− C B V NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. SEATING PLANE E R R1 Z A S 12 3 4 5 U K F J L H D G 5 PL 0.13 (0.005) M T 2.2 0.086 0.34 5.36 0.013 0.217 5.8 0.228 10.6 0.417 0.8 0.031 SCALE 4:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. DOCUMENT NUMBER: DESCRIPTION: 98AON12855D INCHES MIN MAX 0.235 0.245 0.250 0.265 0.086 0.094 0.020 0.028 0.018 0.023 0.024 0.032 0.180 BSC 0.034 0.040 0.018 0.023 0.102 0.114 0.045 BSC 0.170 0.190 0.185 0.210 0.025 0.040 0.020 −−− 0.035 0.050 0.155 0.170 MILLIMETERS MIN MAX 5.97 6.22 6.35 6.73 2.19 2.38 0.51 0.71 0.46 0.58 0.61 0.81 4.56 BSC 0.87 1.01 0.46 0.58 2.60 2.89 1.14 BSC 4.32 4.83 4.70 5.33 0.63 1.01 0.51 −−− 0.89 1.27 3.93 4.32 GENERIC MARKING DIAGRAMS* RECOMMENDED SOLDERING FOOTPRINT* 6.4 0.252 DIM A B C D E F G H J K L R R1 S U V Z XXXXXXG ALYWW AYWW XXX XXXXXG IC Discrete XXXXXX A L Y WW G = Device Code = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “ G”, may or may not be present. Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. DPAK−5 CENTER LEAD CROP PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative