T1610T-8T

T1610T-8T Datasheet 16 A 800 V logic level Triac in TO-220AB package Features A2 • • • G Medium current Triac Three quadrants ECOPACK2 compliant Applications A1 A2 G A2 A1 • • • • • • General purpose AC line load switching Motor control circuits Small home appliances Lighting Inrush current limiting circuits Overvoltage crowbar protection Description TO-220AB Available in through-hole package, the T1610T-8T Triac can be used for the on/off or phase angle control function in general purpose AC switching. This device can be directly driven by a microcontroller due to its 10 mA gate current requirement. Product status link T1610T-8T Product summary Order code T1610T-8T Package TO-220AB IT(RMS) 16 A VDRM/VRRM 800 V VDSM/VRSM 900 V IGT 10 mA DS10472 - Rev 3 - September 2019 For further information contact your local STMicroelectronics sales office. www.st.com T1610T-8T Characteristics 1 Characteristics Table 1. Absolute maximum ratings (limiting values) Symbol Value Unit Tc = 129 °C 16 A F = 50 Hz t = 20 ms 120 F = 60 Hz t = 16.7 ms 126 tp = 10 ms 95 Tj = 150 °C 600 Tj = 125 °C 800 Non repetitive surge peak off-state voltage tp = 10 ms 900 V dl/dt Critical rate of rise of on-state current IG = 2 x IGT, tr ≤ 100 ns F = 100 Hz 100 A/µs IGM Peak gate current Tj = 150 °C 4 A Tj = 150 °C 1 W Storage junction temperature range -40 to +150 °C Tj Operating junction temperature range -40 to +150 °C TL Maximum lead temperature soldering during 10 s 260 °C IT(RMS) ITSM I2t Parameter On-state RMS current (full sine wave) Non repetitive surge peak on-state current (Tj initial = 25 °C) I2t value for fusing, (Tj initial = 25 °C) VDRM, VRRM Repetitive surge peak off-state voltage VDSM, VRSM PG(AV) Tstg tp = 20 µs Average gate power dissipation A A2s V Table 2. Electrical characteristics (Tj = 25 °C unless otherwise specified) Symbol Test conditions Value Min. 0.5 Max. 10 I - II - III Max. 1.3 V I - II - III Min. 0.2 V Max. 15 mA IGT VD = 12 V, RL = 30 Ω I - II - III VGT VD = 12 V, RL = 30 Ω VGD VD = VDRM, RL = 3.3 kΩ , Tj = 125 °C (1) IH IL dV/dt(1) IT = 500 mA IG = 1.2 x IGT I - III II VD = VR = 536 V, gate open Tj = 125 °C VD = VR = 402 V, gate open Tj = 150 °C (dV/dt)c = 0.1 V/μs (dI/dt)c(1) (dV/dt)c = 10 V/μs Unit Max. Min. Tj = 125 °C Tj = 150 °C Tj = 125 °C Tj = 150 °C 20 25 250 170 mA mA V/µs 21.6 Min. 15.1 11.3 A/ms 5 1. For both polarities of A2 referenced to A1 DS10472 - Rev 3 page 2/11 T1610T-8T Characteristics Table 3. Static characteristics Symbol VT(1) Test conditions Value Unit ITM = 22.6 A, tp = 380 µs Tj = 25 °C Max. 1.55 VTO Threshold voltage Tj = 150 °C Max. 0.85 Rd(1) Dynamic resistance Tj = 150 °C Max. 27 mΩ 7.5 µA (1) IDRM, IRRM Tj = 25 °C VD = VR = 800 V Tj = 125 °C VD = VR = 600 V Tj = 150 °C V Max. Max. 1.0 mA 3.0 1. For both polarities of A2 referenced to A1 Table 4. Thermal parameters Symbol DS10472 - Rev 3 Parameter Value Unit Rth(j-c) Junction to case (AC) 1.1 °C/W Rth(j-a) Junction to ambient 60 °C/W page 3/11 T1610T-8T Characteristics (curves) 1.1 Characteristics (curves) Figure 1. Maximum power dissipation versus on-state RMS current I (A) 18 T(RMS) P(W) 20 Figure 2. On-state RMS current versus case temperature 18 16 16 14 14 12 12 10 10 8 8 6 6 4 4 180 ° 2 α 2 IT(RMS)(A) α 0 0 2 4 6 8 10 12 14 16 Figure 3. On-state RMS current versus ambient temperature (free air convection) I (A) 3 T(RMS) Tc(°C) 0 0 75 50 25 100 150 125 Figure 4. Relative variation of thermal impedance versus pulse duration K = [Z / R ] th th 1.0E+00 Zth(j-c) 2.5 Zth(j-a) 2 1.5 1.0E-01 1.0 0.5 tP(s) Ta(°C) 0 0 75 50 25 100 125 150 Figure 5. Relative variation of gate trigger voltage and current versus junction temperature (typical values) I V [ T ] / IGT, VGT [ Tj = 25 °C] 3.0 GT, GT j 1.0E-02 1.0E-03 1.0E-02 1.0E-01 1.0E+00 1.0E+01 1.0E+02 1.0E+03 Figure 6. Relative variation of holding current and latching current versus junction temperature (typical values) 2.0 IH, IL [ Tj ] / IH, IL [ Tj = 25 °C] 2.5 I 2.0 I GT GT Q3 1.5 Q1-Q2 1.5 1.0 1.0 VGT I L 0.5 0.5 I H Tj(°C) 0.0 -40 DS10472 - Rev 3 -25 0 25 50 75 100 125 150 0.0 -50 Tj(°C) -25 0 25 50 75 100 125 150 page 4/11 T1610T-8T Characteristics (curves) Figure 7. Surge peak on-state current versus number of cycles I (A) 130 TSM 120 Non repetitive Tj initial = 25 °C 110 100 90 80 70 60 50 40 Repetitive T = 129 °C c 30 20 10 Number of cycles 0 10 100 1 10000 ITSM(A) dl/dt limitation: 100 A/µs Tj initial = 25 °C ITSM 20 ms 1000 One cycle 100 Tp(ms) 10 0.01 1000 Figure 9. On-state characteristics (maximum values) 1000 Figure 8. Non repetitive surge peak on-state current 0.10 1.00 10.00 Figure 10. Relative variation of critical rate of decrease of main current versus junction temperature (typical values) ITM(A) Tj max: Vto= 0.85 V Rd = 27 mΩ 8 (dI/dt)c[Tj] / (dI/dt)c[Tj = 150 °C] (dV/dt)c = 10 V/µs 7 6 100 5 4 10 3 2 Tj = 150 °C 1 0.0 0.5 Tj = 25 °C 1.0 1.5 2.0 2.5 3.0 VTM(V) 1 3.5 0 25 4.0 Figure 11. Relative variation of static dV/dt immunity versus junction temperature (typical values) 5 Tj(°C) 75 50 125 100 150 Figure 12. Relative variation of critical rate of decrease (di/dt)c of main current versus reapplied (dV/dt)c (maximum values) dV/dt [Tj] / dV/dt [Tj= 150 °C] 3 (dI/dt)c [ (dV/dt)c ] / specified (dI/dt)c VD = VR = 402 V; 150 (°C) 4 2 3 Tj = 150 (°C) 2 1 1 0 25 DS10472 - Rev 3 Tj = 125 (°C) Tj (°C) 50 75 100 125 150 0 0.1 (dV/dt)c (V/µs) 1.0 10.0 100.0 page 5/11 T1610T-8T Characteristics (curves) Figure 13. Relative variation of leakage current versus junction temperature for different values of blocking voltage (typical values) 1.0E+00 IDRM, IRRM [ Tj; VDRM, VRRM] / IDRM, IRRM V =V = 800 V DRM RRM 1.0E-01 V DRM =V RRM = 600 V 1.0E-02 V DRM 1.0E-03 1.0E-04 25 DS10472 - Rev 3 =V RRM = 400 V [T = 125 °C; 800 V] j [T = 150 °C; 600 V] j Tj (°C) 50 75 100 125 150 page 6/11 T1610T-8T Package information 2 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. 2.1 TO-220AB package information • • • Epoxy resin is halogen free and meets UL94 flammability standard, level V0 Lead-free plating package leads Recommended torque: 0.4 to 0.6 N·m Figure 14. TO-220AB package outline DS10472 - Rev 3 page 7/11 T1610T-8T TO-220AB package information Table 5. TO-220AB package mechanical data Dimensions Ref. Millimeters Min. A Typ. 15.20 a1 Inches Max. Min. 15.90 0.5984 3.75 Typ. Max. 0.6260 0.1476 a2 13.00 14.00 0.5118 0.5512 B 10.00 10.40 0.3937 0.4094 b1 0.61 0.88 0.0240 0.0346 b2 1.23 1.32 0.0484 0.0520 C 4.40 4.60 0.1732 0.1811 c1 0.49 0.70 0.0193 0.0276 c2 2.40 2.72 0.0945 0.1071 e 2.40 2.70 0.0945 0.1063 F 6.20 6.60 0.2441 0.2598 I 3.73 3.88 0.1469 0.1528 L 2.65 2.95 0.1043 0.1161 I2 1.14 1.70 0.0449 0.0669 I3 1.14 1.70 0.0449 0.0669 I4 15.80 16.80 0.6220 M 16.40 2.6 0.6457 0.6614 0.1024 1. Inch dimensions are for reference only. DS10472 - Rev 3 page 8/11 T1610T-8T Ordering information 3 Ordering information Figure 15. Ordering information scheme T 16 10 T - 8 T Triac Current 16 = 16 A Gate sensitivity 10 = 10 mA Specific application T = Increased (dI/dt) and dV/dt producing reduced ITSM Voltage 8 = 800 V Package T = TO-220AB Table 6. Ordering information DS10472 - Rev 3 Order code Marking Package Weight Base qty. Delivery mode T1610T-8T T1610T-8T TO-220AB 2.0 g 50 Tube page 9/11 T1610T-8T Revision history Table 7. Document revision history DS10472 - Rev 3 Date Version Changes 23-Oct-2014 1 Initial release. 17-Sep-2019 2 Updated Figure 14 and Table 5. 23-Sep-2019 3 Updated Table 2. page 10/11 T1610T-8T IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2019 STMicroelectronics – All rights reserved DS10472 - Rev 3 page 11/11