VN330SP

® VN330SP QUAD HIGH SIDE SMART POWER SOLID STATE RELAY T YPE VN330SP * per Channel ** at TJ = 85 oC s s V dema g * R DS(on) * V CC -55V 0.32 Ω ** I OUT * 0.7 A V CC 36 V s s s s s OUTPUT CURRENT: 0.7A PER CHANNEL DIGITAL INPUTS CLAMPED AT 32V MINIMUM VOLTAGE SHORTED LOAD AND OVERTEMPERATURE PROTECTIONS BUILT-IN CURRENT LIMITER UNDER VOLTAGE SHUT DOWN OPEN DRAIN DIAGNOSTIC OUTPUT FAST DEMAGNETIZATION OF INDUCTIVE LOADS 10 1 Power SO-10 TM DESCRIPTION The VN330SP is a monolithic device made using STMicroelectronics VIPower Technology, intended for driving four indipendent resistive or inductive loads with one side connected to ground. BLOCK DIAGRAM Active current limitation avoids dropping the system power supply in case of shorted load. Built-in thermal shut-down protects the chip from over temperature and short circuit. The open drain diagnostic output indicates short circuit and overtemperature conditions. February 1999 1/9 VN330SP ABSOLUTE MAXIMUM RATING Symb ol VCC -V CC I OUT IR I IN I DIAG V ESD E AS P tot Tj T s tg Power Supply Voltage Reverse Supply Voltage Output Current (cont.) Reverse Output Current (per channel) Input Current (per channel) DIAG Pin Current Electrostatic Discharge (1.5 k Ω, 100 pF) Single Pulse Avalanche Energy per Channel Not Symultaneously (see figure 1) Power Dissipation at T c ≤ 25 C Junction Operating Temperature Storage Temperature o Parameter Value 45 -0.3 Internally Limited -6 ± 10 ± 10 2000 400 Internally Limited Internally Limited -55 to 150 Unit V V A A mA mA V mJ W o o C C CONNECTION DIAGRAM CURRENT AND VOLTAGE CONVENTIONS 2/9 VN330SP THERMAL DATA R t hj-ca se R t hj- amb Thermal Resistance Junction-case (1) Thermal Resistance Junction-ambient ($) Max Max 2 50 o o C/W C/W (1) All channels ON ($) When mounted using minimum recommended pad size on FR-4 board ELECTRICAL CHARACTERISTICS (10 V < VCC < 36 V; -25 oC < TJ < 125 oC unless otherwise specified) POWER Symb ol VCC R on IS V demag Parameter Supply Voltage On State Resistance Supply Current Output Voltage at Turn-Off I OUT = 0.5 A I OUT = 0.5 A T J = 125 C T J = 85 o C o Test Cond ition s Min. 10 Typ . Max. 36 0.4 0.32 1 10 Un it V Ω Ω mA mA V All Channels O ff o On State (Tj =125 C) I out1 .. Io ut4 =0 I out = 0.5A LLOAD = 1 mH V CC -65 VCC -55 V CC -45 SWITCHING (VCC = 24 V) Symb ol t d(on) Parameter Turn-on Delay Time Of Output Current Test Cond ition s I OUT = 0.5 A Resistive Load Input Rise T ime < 0.1 µ s o T j = 25 C o T j = 125 C I OUT = 0.5 A Resistive Load Input Rise T ime < 0.1 µ s T j = 25 o C o T j = 125 C Min. Typ . Max. Un it 30 40 60 µs µs tr Rise Time O f O utput Current 50 100 115 µs µs t d(of f) Turn-off Delay Time O f I OUT = 0.5 A Resistive Load Output Current Input Rise T ime < 0.1 µ s T j = 25 o C o T j = 125 C Fall T ime Of Output Current I OUT = 0.5 A Resistive Load Input Rise T ime < 0.1 µ s o T j = 25 C o T j = 125 C I OUT = 0.5 A I OUT = I lim I OUT = 0.5 A I OUT = I lim Tj = 25 C Tj = 25 C o o 20 30 40 µs µs tf 8 15 20 0.5 2 2 4 µs µs A/ µ s A/ µ s A/ µ s A/ µ s (di/dt) on (di/dt) off Turn-on Current Slope Turn-off Current Slope 3/9 VN330SP ELECTRICAL CHARACTERISTICS (continued) LOGIC INPUT (Each Channel) Symb ol VI L VI H V I(hyst.) I IN I LGND V ICL Parameter Input Low Level Voltage Input High Level Voltage (see note 1) Input Hysteresis Voltage Input Current Output Current in Ground Disconnection Input Clamp Voltage (see note 1) V I N = 0 to 30 V V I N = 0 to 2 V V CC = V I NX = G ND = DIAG = 24 V o T J = 25 C I IN = 1 mA I IN = -1 mA 32 36 -0.7 25 25 3.5 0.5 600 Test Cond ition s Min. Typ . Max. 2 Un it V V V µA µA mA V V note 1 : The input voltage is internally clamped at 32V minimum, it is possible to connect the input pins to an higher voltage via an external resistor calculate to not exceed 10 mA. PROTECTION AND DIAGNOSTICS Symb ol V STAT (• ) V SCL ( • ) V USD V OL I LIM I OVPK I DI AGH I LOAD t SC T TSD TR Parameter Status Voltage Output Low Status Clamp Voltage Under Voltage Shut Down Low State Out Voltage DC Short Circuit Current Peak Short Circuit Current Leakage on diag pin in high state Output Leakage Current Delay Time of Current Limiter Thermal Shut-down Temperature Reset Temperature 150 135 170 155 V I N = VI Lj V CC = 24 V R LOAD ≥ 10 M Ω R L OAD < 10 mΩ 0.7 Test Cond ition s I STAT = 5 mA (F ault Condition) I STAT = 1 mA I STAT = -1 mA 32 5 36 -0.7 8 1.5 2.5 4 100 VIN = V IL 50 100 Min. Typ . Max. 1 Un it V V V V V A A µA µA µs o V CC = 24 V V in =30V R LOAD < 10 m Ω (see figure 2) V DIAG = 24 V V CC = 10 to 36V C C o ( •) Status determination > 100 µs after the switching edge. Note: If INPUTn pin is left floating the corresponding channel will automatically switch off. If GND pin is disconnetted, all channels will switch off provided VCC does not exceed 36V 4/9 VN330SP FIGURE 1: Avalanche Energy Test Circit FIGURE 2: Peak Short Circuit Current Test Circit 5/9 VN330SP TRUTH TABLE I NPUTn Normal Operation O ver-temperature Under-voltage Shorted Load (current limitation) L H L H L H L H OUT PUT n L H L L L L L H DIAG NO STIC H H H L H H H H FIGURE 3: Switching Waveforms 6/9 VN330SP SWITCHING PARAMETERS TEST CONDITIONS DRIVING CIRCUIT 7/9 VN330SP PowerSO-10 MECHANICAL DATA DIM. MIN. A A1 B c D D1 E E1 E2 E3 E4 e F H h L q α 0 o mm TYP. MAX. 3.65 0.10 0.60 0.55 9.60 7.60 9.50 7.40 7.60 6.35 6.10 1.27 1.25 13.80 0.50 1.20 1.70 8o 1.80 0.047 1.35 14.40 0.049 0.543 MIN. 0.132 0.000 0.016 0.013 0.370 0.291 0.366 0.283 0.283 0.240 0.232 3.35 0.00 0.40 0.35 9.40 7.40 9.30 7.20 7.20 6.10 5.90 inch TYP. MAX. 0.144 0.004 0.024 0.022 0.378 0.300 0.374 0.291 0.300 0.250 0.240 0.050 0.053 0.567 0.002 0.071 0.067 B 0.10 A B 10 = H = A F A1 = 6 = = = E = 1 5 e 0.25 M = E2 E3 E1 E4 = = A = SEATING PLANE DETAIL ”A” Q B C h D = D1 = = = SEATING PLANE = A1 L DETAIL ”A” α 0068039-C 8/9 VN330SP Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics © 1999 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. http://www.st.com . 9/9